BANWOOD x Bonton Collab Kids Balance Bike Pink Installation Guide
- June 1, 2024
- BANWOOD
Table of Contents
BANWOOD x Bonton Collab Kids Balance Bike Pink
Product Specifications
- Maximum Weight Capacity: 50kg / 110lbs
- Height: 0.95m / 3’1″
- Dimensions: XXcm XX
Product Usage Instructions
Assembly
Follow the provided assembly instructions to set up the First Go! product.
Maintenance
Apply a layer of beeswax regularly to maintain and protect the bike’s
lifespan. Lubricate moving parts with oil or grease periodically. Replace
worn-out parts immediately.
Safety Guidelines
Always adhere to safety guidelines while using the product. Ensure the
recommended weight limits are not exceeded. Use under adult supervision.
Certifications
The product meets safety standards such as 16 CFR 1203 / EN
1078:2012+A1:2012. It is CPSC and CE certified.
Frequently Asked Questions (FAQ)
-
Q: What is the maximum weight capacity of the First Go! product?
A: The maximum weight capacity is 50kg or 110lbs. -
Q: How often should I apply beeswax to the bike?
A: Beeswax should be applied regularly to maintain and protect the bike’s lifespan. -
Q: Are replacement parts available for the First Go! product?
A: Yes, replacement parts are available. Please contact info@banwood.com for assistance.
Website: www.banwood.com
Email: info@banwood.com
Products must be assembled by an adult – Children should be kept away from the
product during assembly due to possible risk of injury. Choking hazard to
children under the age of 3 years – contains small parts prior to assembly.
When unpacking the bicycle, properly dispose of all plastic wrappings.
Your bicycle is partially assembled. These instructions are designed to guide
you through the final assembly, as well as to adjust the bicycle. This guide
includes information on the parts that are disassembled and need to be
adjusted. All fasteners should be fully tightened. For further information,
please contact the Banwood customer service department at
info@banwood.com.
- A. Handlebar with grips, bell, stem.
- B. Assembled frame set & rear wheel.
- C. Front Wheel.
- D. Saddle with seat post.
- E. Basket.
Tools: Allen key (x2) 6mm – 5mm / Spanner (x1) 15mm.
HANDLEBAR ASSEMBLY
Insert the handlebar, ensuring it is fitted above the bar’s safety line. Using
the hex key provided, tighten the bolt at the top of the bar.
FRONT WHEEL ASSEMBLY
Place the wheel axle inside the fork. Slide a large washer over each of the
bolts and situate the inside of the axle to secure it. Please note that the
large washers must be pressed into the lowest safety hole of the fork ends and
between the bolt head and the fork. Using the spanner provided, tighten the
exterior bolts.
Please pay attention: Place the wheel axle within the fork dropouts.
SADDLE ASSEMBLY
Loosen the bolt head on the seat post bracket to allow the saddle to move.
Adjust the height so that your child’s feet rest flat and comfortably on the
floor with a slight band at the knee. BASKET ASSEMBLY
Attach the strap on the basket to the handlebar and adjust it to a suitable
position.
Recommended maximum weight: 25,4 kg (56 lb.). Recommended maximum basket
weight capacity: 5 kg (11lb.). – Excessive weight may cause a hazardous or
unstable condition.
Recommended age: 3-5 years
ATTENTION! Please keep these instructions for future reference.
WARNING! This toy must be used with caution as it requires great skill to
be able to avoid falls or collisions that could cause injury to the user or
third parties.
WARNING! It should only be used under direct adult supervision. Do not
use on public roads. The suitable surface for the correct use of the toy must
be flat, level and have good grip. It is necessary to carry out periodic
maintenance and checks of the fastening elements, such as screws, nuts, bolts,
etc. If these checks are not carried out, the toy may roll over or cause a
fall. Do not use in areas that may pose a threat to the driver, pedestrians,
or pets, such as steep slopes, steps, hills, streets, swimming pools or near
rivers. Protects your children’s head with an approved safety helmet and
appropriate clothing and closed shoes riding your First Go. Always wear a
properly fitted helmet that complies with U.S. Consumer Product Safety
Commission (CPSC) Standard 16 CFR 1203 / EN 1078:2012+A1:2012 and CE
certificated by European Union. Mounting the toy is recommended in any indoor
or outdoor area if it is on a smooth surface free of objects. This toy does
not have a braking system. The cyclist must stop the bicycle with their feet.
Always wear shoes when using the bicycle. This toy must be used with caution,
as it requires skill to be able to avoid collisions that could cause injury to
the user and to third parties. Never allow more than one rider.
CARE AND MAINTENANCE
Storage the bike inside and never leave your First Go! outside for long periods of time. After riding, remove any water or mud with a clean cloth. Keep your First Go! in a dry place when not in use. Check your tire pressure regularly. Applying a periodic coat of beeswax to maintain and protect the life of your bicycle. Oil or grease moving parts periodically. Any parts showing evidence of wear should bereplaced immediately.