CREATIVE LABS EF1090 Creative Zen Air Lightweight True Wireless Sweatproof In Ears Instructions
- June 13, 2024
- CREATIVE LABS
Table of Contents
LABS EF1090 Creative Zen Air
Lightweight True Wireless Sweatproof In
Ears Instructions
EF1090 Creative Zen Air Lightweight True Wireless Sweatproof In Ears
Creative Zen Air Pro QSG
OVERVIEW
BATTERY CASE INDICATOR
CONTROLS
STREAMING MODES
Creative Zen Air Pro supports both Bluetooth® LE Audio with Ultra-low Latency
(ULL) Mode and Classic Bluetooth. The earbuds will attempt to pair in ULL mode
when a compatible device is used.
Unicast Mode (LC3)
Unicast mode lets the user wirelessly connect to a compatible Bluetooth LE
audio receiver to enjoy high-definition audio streaming on a one-to-one basis.
Broadcast Mode (LC3)
Broadcast mode lets the user broadcast wireless audio from an audio source to
an unlimited number of supported audio devices. The LED indicator will start
flashing white to indicate that it is currently broadcasting. Note that the
broadcast stream is unencrypted and any supported device can join the stream
if it is within range.
Ultra-low Latency Mode (LC3+)
ULL mode lets the users enjoy a smooth, lag-free, and consistent viewing
experience, great for time sensitive media such as movies and games. Visit
creative.com for more information on products
supporting ULL mode.
MASTER RESET
With both earbuds in the charging case, press and hold the multifunction
button on the charging case for 10 seconds to perform a Master Reset. The
charging case LED indicator will blink green and turn off upon completion.
Master Reset is reserved for cases where users encounter issues while earbuds
are in use or during situations such as: Bluetooth Pairing failure, failure to
pair secondary earbud with the main earbud, or to reset all data.
Common Connectivity Issues
This article highlights a phenomena and recommendation for music cutting out
and earbuds that do not stay connected. When pairing a smart mobile device
with the earbuds, the signal is strongest when there is a line-of-sight
between the pairing devices.
If the signal passes through the body, which is mostly made up of water fluid,
it may get absorbed, which may result in pairing difficulty. If the mobile
device is already connected to the earbuds, it may result in signal lost or
the earbuds may get disconnected.
Bluetooth Pairing
TECHNICAL SPECIFICATIONS
Headphone Drivers: 10 mm Neodymium drivers x 2
Frequency Response : 20–20,000 Hz
Microphone: Omni-directional MEMS x 6
Total Playtime:
- Up to 7 hours on a single charging
- Up to 27 hours total playtime
Bluetooth LE Audio Modes:
- Unicast (CIS) mode
- Broadcast (BIS) mode
Classic Bluetooth Version: Bluetooth 5.3
Classic Bluetooth Profiles:
- A2DP (Advanced Audio Distribution Profile)
- AVRCP (Audio / Video Remote Control Profile)
- HFP (Hands-free profile)
Supported Audio Codecs: LC3+ (ULL), LC3, AAC, SBC
Wireless Operating Range: Up to 10m / 33 ft measured in open space. Walls
and structures will affect range of device.
Max RF Output Power (For EU/UK)
• BT/BLE: 10dBm
Operating Frequency:
- Bluetooth: 2402–2480 MHz
- WPC: 121.0-134.6kHz (WPC H-field value:-10.57dBuA/m at 10m) Commented [LC(1]: Refer to draft report
Input Rating: 5V⎓1A
Operating Temperature: 0–45°C
IP Rating : IPX5 (Earbuds only)
Battery:
-
Earbuds: 3.7V 60mAh 0.222Wh Lithium-ion button battery
-
Charging case: Lithium-ion polymer battery: 3.7V 500 mAh 1.85 Wh
Charging interface: -
Qi-compatible wireless charging, USB-A to USB-C (Charging)
Note: Compliance marking are located at the bottom of the product.
Operating frequency for China translation only;
2400–2483.5 MHz
2402–2480 MHz
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>