PDi PD196-428R3 Arm Mounted TV Installation Guide

September 28, 2024
PDi

PD196-428R3 Arm Mounted TV

“`html

Specifications:

  • Model Number: Arm Mounted PDi TV

  • Document Number: PD196-428R3

  • Manufacturer: PDi Communication Systems, Inc.

  • Location: Springboro, Ohio, USA

  • Website: www.pdiarm.com and
    www.mymedTV.com

  • Phone: 800.628.9870

Product Usage Instructions:

Installation:

  1. Remove PDi TV from the box, keeping the foam inserts and box
    for potential returns.

  2. Remove screw PDISHCS252075 and discard washer PD220-002.

  3. If present, remove the nose covers for the PDi swing arm.

  4. Slide the PDi TV into the nose ensuring proper fit and
    alignment, then install screw PDISHCS252075.

  5. Remove the safety brake pin by loosening the nuts on each end
    and store it in the swing arm for easy access.

  6. Connect cables from the arm to the PDi TV following safety
    procedures.

Mounting:

  1. Place spacers PD242-686 in the four holes in the rear
    cabinet.

  2. Hold the TV against the mounting plate and insert mounting
    screws through the VESA mounting plate, threading them into the
    bracket inside the TV through the spacers.

  3. Start by installing the top two screws first and finger
    tighten, ensuring cables do not get pinched.

FAQ:

Q: What tools are needed for installation?

A: You will need a 3/16 hex wrench and safety
glasses/goggles.

Q: How do I ensure safety during
installation?

A: Always wear safety glasses/goggles, disable
power to the TV following facility procedures, and keep the safety
brake pin in place to prevent arm recoil.

“`

MODEL NUMBER:
Arm Mounted PDi TV
Installation Instructions

Document Number:
PD196-428R3
Page 1 of 4

INTRODUCTION
This document provides the information to install any low voltage PDi TV. These instructions cover the standard design of the arm mounted PDi TV with top mount or rear mount and any customizations incorporated may not be specifically outlined in these instructions.
Note: See the specific Installation Instruction for the VESA mount for additional details for Rear Mounted TV’s.
SAFETY
1. Always wear safety glasses/goggles to prevent injury from debris. 2. Follow the installation/removal instructions for your existing products. 3. Prior to installing or removing the TV, ensure power to the TV has been disabled according to the safety
procedures of the facility.
DANGER: ARM RECOIL HAZARD. The safety brake pin must remain in the SAFETY BRAKE PIN HOLE whenever the television set is removed from the arm or when the arm is removed from the wall bracket to prevent the arm from springing open.

INSTALLATION ­ TOP MOUNTED UNIT
Tools needed 3/16″ hex wrench Safety glasses/goggles
1. Remove PDi TV from the box. Be sure to save the foam inserts and the box as they will be needed if you ever need to return your PDi TV. Note: Store the monitor as shown when not mounted on the arm.

PDi Communication Systems, Inc. 40 Greenwood Ln Springboro, Ohio 45066 USA www.pdiarm.com and www.mymedTV.com Phone 800.628.9870

MODEL NUMBER:
Arm Mounted PDi TV
Installation Instructions

Document Number:
PD196-428R3
Page 2 of 4

2. Remove screw PDISHCS252075 and retaining washer PD220-002. Discard the washer PD220-002 and place screw PDISHCS252075 to the side.

3. If they have been installed, remove the nose covers for the PDi swing arm. See Arm Installation Instructions for additional details.
4. Slide the PDi TV into the nose so that mounting washer fits inside the slot in the nose, the retainer plate rests inside the nose and the hole in the retainer plate aligns with the mounting hole of the nose. Install screw PDISHCS252075 in the mounting hole, and tighten with 3/16″ hex wrench.

PDi Communication Systems, Inc. 40 Greenwood Ln Springboro, Ohio 45066 USA www.pdiarm.com and www.mymedTV.com Phone 800.628.9870

MODEL NUMBER:
Arm Mounted PDi TV
Installation Instructions

Document Number:
PD196-428R3
Page 3 of 4

5. The safety brake pin can now be removed by removing one of the nuts installed on each end of the safety pin. After removing the safety pin, re- install the nut and store the safety pin in the nose of the swing arm. This will allow for convenient access if there is a need to remove the TV.
6. Ensure that power is safely removed from the power supply to the TV and arm. Connect the cables from the arm to the PDi TV as required, be sure to follow all appropriate safety procedures for working with the cables.
7. Re-install the covers for the PDi swing arm. See Arm Installation Instructions for additional details. INSTALLATION ­ REAR MOUNTED UNIT Tools needed #2 Phillips screwdriver Safety glasses/goggles
1. Remove PDi TV from the box. Be sure to save the foam inserts and the box as they will be needed if you ever need to return your PDi TV.
2. Place the spacers, PD242-686, in the four holes in the rear cabinet. 3. Holding the TV against the mounting plate, insert the mounting screws through the VESA mounting plate
and thread them into the bracket inside the TV, through the spacers. It is recommended to install the top two screws first, and finger tighten. See figure below. Note: Be sure that the cables coming out the rear of the TV do not get pinched between the TV and the mounting plate.
PDi Communication Systems, Inc. 40 Greenwood Ln Springboro, Ohio 45066 USA www.pdiarm.com and www.mymedTV.com Phone 800.628.9870

MODEL NUMBER:
Arm Mounted PDi TV
Installation Instructions

Document Number:
PD196-428R3
Page 4 of 4

4. After all four screws are installed, use the screwdriver to tighten the screws. 5. Ensure that power is safely removed from the power supply to the TV and arm. Connect the cables from
the arm to the PDi TV as required, be sure to follow all appropriate safety procedures for working with the cables. WARRANTY PDi Communication Systems, Inc., (“PDi”) standard warranty information is found at pdiarm.com. For information regarding authorized servicing and all other information pertaining to this warranty, please contact PDi COMMUNICATION SYSTEMS, INC. at 40 Greenwood Ln, Springboro, Ohio 45066 or phone 800628-9870 and ask for the PDi ProServices team.
PDi Communication Systems, Inc. 40 Greenwood Ln Springboro, Ohio 45066 USA www.pdiarm.com and www.mymedTV.com Phone 800.628.9870

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals