PD196-428R2 Arm Mounted PDi TV Installation Guide

June 1, 2024
PDi

PD196-428R2 Arm Mounted PDi TV

PD196-428R2-Arm-Mounted-PDi-TV-PRODUCT

Specifications

  • Model Number: Arm Mounted PDi TV
  • Document Number: PD196-428R2
  • Installation: Top Mount

Product Usage Instructions

Safety Precautions

  1. Always wear safety glasses/goggles to prevent injury from debris.
  2. Follow the installation/removal instructions for your existing products.

Tools Required

  1. 3/16 hex wrench
  2. Safety glasses/goggles

Installation Steps

DANGER: ARM RECOIL HAZARD. Ensure the safety
brake pin remains in place to prevent accidents.

  1. Remove PDi TV from the box, retaining foam inserts and box for future use.
  2. Remove screw PDISHCS252075 and discard washer PD220-002.
  3. If nose covers are installed, remove them following additional instructions.
  4. Slide the PDi TV into the nose ensuring proper alignment and fasten with screw PDISHCS252075.
  5. Connect cables from the arm to the PDi TV following safety procedures.
  6. Re-install the covers for the PDi swing arm.

Warranty Information

  • PDi Communication Systems, Inc., provides warranty details on pdiarm.com. For servicing and warranty inquiries, contact PDi
  • COMMUNICATION SYSTEMS, INC. at 40 Greenwood Ln, Springboro, Ohio 45066 or call 800.628.9870 for assistance.

INTRODUCTION

This document provides the information to install any arm-mounted PDi TV with a top mount. These instructions cover the standard design of the arm-mounted PDi TV with top mount and any customizations incorporated may not be specifically outlined in these instructions.
Note : For rear-mounted TVs see the specific Installation Instructions for the mount.

SAFETY

  1. Always wear safety glasses/goggles to prevent injury from debris.
  2. Follow the installation/removal instructions for your existing products.

TOOLS REQUIRED

  1. 3/16” hex wrench
  2. Safety glasses/goggles

INSTALLATION

DANGER: ARM RECOIL HAZARD. The safety brake pin must remain in the SAFETY BRAKE pinhole whenever the television set is removed from the arm or when the arm is removed from the wall bracket to prevent the arm from springing open.

  1. Remove the PDi TV from the box. Be sure to save the foam inserts and the box as they will be needed if you ever need to return your PDi TV.
    Note: Store the monitor as shown when not mounted on the arm.

  2. Remove screw PDISHCS252075 and retaining washer PD220-002. Discard the washer PD220-002 and place screw PDISHCS252075 to the side.PD196-428R2-Arm-Mounted-PDi-TV-FIG-4

  3. If they have been installed, remove the nose covers for the PDi swing arm. See Arm Installation Instructions for additional details.

  4. Slide the PDi TV into the nose so that the mounting washer fits inside the slot in the nose, the retainer plate rests inside the nose and the hole in the retainer plate aligns with the mounting hole of the nose. Install screw PDISHCS252075 in the mounting hole.

  5. Connect the cables from the arm to the PDi TV as required, be sure to follow all appropriate safety procedures for working with the cables.

  6. Re-install the covers for the PDi swing arm. See Arm Installation Instructions for additional details.

WARRANTY

PDi Communication Systems, Inc., (“PDi”) standard warranty information is found at pdiarm.com. For information regarding authorized servicing and all other information about this warranty, please
contact PDi COMMUNICATION SYSTEMS, INC. at 40 Greenwood Ln, Springboro, Ohio 45066 or phone 800-628-9870 and ask for the PDi Pro Services team.

PDi Communication Systems, Inc.

FAQ

  • Q: What should I do if I encounter difficulties during installation?
    • A: If you face challenges during installation, refer to the specific installation instructions or contact PDi Communication Systems, Inc. for support at the provided contact details.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals