ALL LED AiQ-WSW-4Z iQ Smart 4 Zone LED Wall Station Installation Guide
- September 27, 2024
- ALL LED
Table of Contents
AiQ-WSW-4Z iQ Smart 4 Zone LED Wall Station
“`html
Specifications
- Product: AiQ/WSW/4Z Smart-WS IQ Wall Station
- Product Code: AiQ/WSW/4Z
- Protocol: ZigBee 3.0
- Input Voltage: 100-240VAC
- Transmission Frequency: 2.4GHz
- Transmission Range (Uninterrupted): 30m
- Ingress Protection: IP20
- Dimensions: 86 x 86 x 30mm
Product Information
PLEASE READ BEFORE USE!
Environmental Protection: Waste electrical products should not
be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for
recycling advice.
The manufacturer will not be deemed liable or held responsible
for any damages caused by faults or manufacturing defects that may
be present in any of its products or the misuse or incorrect
installation of this device. Your statutory rights are not
affected.
Installation Guide
WARNING : Please wire to torpedo switch to make
connection to smart devices. Once connections have been
established, you can install switch on the wall.
Instructions
-
Group buttons: Click to choose a group, press and hold it down
to turn ON/OFF. -
LED Indicator: Press and hold down to increase/decrease light
intensity of the paired lighting devices. -
All ON/OFF button: Click to switch ON/OFF all paired lighting
devices. Press and hold down to search and pair to Smart Home Hub
or factory reset the dimmer switch. -
Click to play/pause 1 built-in color-changing effect. Press and
hold down to speed up/down effect. -
RGB color wheel: R, G, B, W Channels. Click to select
corresponding channel.
Quick Install Guide
When controlling RGB + CCT light devices, keep short pressing to
turn on CCT channels and get different color ratios. Press and hold
to adjust color temperature smoothly.
When controlling RGBW light devices, keep short pressing to turn
on the 4th channel W and adjust intensity. Press and hold to adjust
W Channel light intensity smoothly.
Usage Instructions
- Connecting Your Remote to a Smart Home Hub (if using a
hub)
-
Step 1: From Smart Home Hub App or Voice Control, add a device
or enter pairing mode. -
Step 2: Press and Hold power button until LED indicator turns
on. -
Step 3: Quickly short press R button. LED indicator will flash.
20 Seconds until timeout. LED indicator blinks x5 quickly for
successful pairing. -
Connecting Your Remote to Intelligent Lighting (without
a hub)-
Step 1: Set receiving device to Find and Bind mode. Lights will
flash indicating Find and Bind mode active for 3 minutes. -
Step 3: Short press 1, 2, 3, or 4 to choose a group that you
would like to pair the device to.
-
FAQ
Q: What should I do if my device is faulty?
A: If you encounter any faults with the product, please contact
our customer service for assistance with returns or
replacements.
“`
Returns & Faulty Items
· If any problem is encountered during or after installation, please call the
ALL LED technical department to get the problem resolved as soon as possible.
· Please do not just return the item to the outlet you purchased it from, as
you are only entitled to a replacement or refund after the unit has undergone
testing and the unit has been confirmed as having a manufacturing
defect/fault. Your statutory rights are not affected.
· The manufacturer will not be deemed liable or held responsible for any
damages caused by faults or manufacturing defects that may be present in any
of its products or the misuse or incorrect installation of this device. Please
refer to our troubleshooting guide for further information.
· All goods are supplied under the terms and conditions of ALL LED LTD, a copy
of which may be obtained upon written request.
General Information
· Interference may occur with other products on the same frequency of 2.4Ghz ·
Product may differ in colour from image on box · Range signal can be reduced
when using within materials such as concrete & metal
Dimensions
INSTALLATION GUIDE
AiQ/WSW/4Z Smart-WS
IQ Wall Station
Technical Specifications
Product Code Protocol Input Voltage Transmission Frequency Transmission Range
(Uninterrupted) Ingress Protection Dimensions
AiQ/WSW/4Z ZigBee 3.0 100-240VAC 2.4GHz 30m IP20 86 x 86 x 30mm
!
PLEASE READ BEFORE USE!
Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice
The manufacturer will not be deemed liable or held responsible for any damages
caused by faults or manufacturing defects that may be present in any of its
products
or the misuse or incorrect installation of this device Your statutory rights
are not affected.
ALL LED LTD 42 Sedgwick Road,
Luton, LU4 9DT
www.allledgroup.com sales@allledgroup.com Tel: +44 (0)208 841 9000
WARNING
Please wire to torpedo switch to make connection to smart devices. Once
connections have been established you can install switch on the wall.
1
Instructions
Group buttons, click to choose a group, press and hold it down to turn ON/OFF
LED Indicator
Press and hold down to increase/decrease light intensity
of the paired lighting devices
All ON/OFF button, click to switch ON/OFF all paired lighting devices.
Press and hold down to search and pair to Smart Home Hub or factory reset the
dimmer switch.
Click to play/ pause 1 built in colour changing effect, press and hold down to
speed up/ down effect
RGB colour wheel
R, G, B, W Channels, click to select corresponding channel
Quick Install Guide
When controls RGB + CCT light devices, keep short pressing to turn on CCT channels and get 25% ww+75% CW, 50% ww+50% CW, 75% WW+25% CW, 100% ww+0%, 0% WW+100% CW one by one. Press and hold to adjust colour temperature smoothly.
When controls RGBW light devices, keep short pressing to turn on the 4th channel W and get 15%, 50%, 75%, 100%, 0% intensity one by one. Press and hold to adjust W Channel light intensity smoothly.
To be able to use a remote with your Smart Home Hub and Intelligent lighting follow (1 and 2). If you would like to use your remote directly with your Intelligent lighting without a Hub, follow Instructions (2).
- Connecting Your Remote to a Smart Home Hub Required if using a hub.
Step 1: From Smart Home Hub App or Voice Control; Add a device or enter pairing mode.
LED Indicator
Step 2: Press and Hold power button until LED indicator turns on.
Step 3: Quickly short press R button. LED indicator will flash. 20 Seconds
until timeout. LED indicator blinks x5 quickly for successful pairing.
Install Tip Care – Unit is supplied with a preflexed plug. Do not install in wall prior to programming. Unit must be in physical proximity to receiving devices. Recommended to set up devices prior to install.
2
- Connecting your Remote to Intelligent lighting.
Step 1: Set receiving device to Find and Bind mode. Lights will fl ash indicating Find and Bind mode active: Duration 3 minutes.
LED Indicator
Step 3: Short press 1, 2, 3 or 4 to choose a group that you would like to pair
the device to.
Step 5: Quickly short press G button to start Find and Bind pairing procedure.
LED indicator will flash for 3 seconds then flash x6 slowly to indicate
successful pairing.
Factory Reset Remote
LED Indicator
Step 1: Press and Hold power button until LED indicator turns on.
Step 2: Quickly short press power button x5. LED indicator flashes x3 quickly
to indicate successful reset.
Step 2: Bring the remote within 10cm of the intelligent lighting device.
Step 4: Press and Hold power button until LED indicator turns on.
Note: All configuration parameters will be reset after the remote is reset or
removed from the network.
Removing Intelligent Lighting from your Remote
Step 1: Set receiving device to Find and Bind mode. Lights will fl ash indicating Find and Bind mode active: Duration 3 minutes.
LED Indicator
Step 2: Bring the remote within 10cm of the intelligent lighting device.
Step 3: Short press 1, 2, 3 or 4 to choose a group to unpair.
Step 5: Quickly short press G button twice to start Find and Bind unpairing
procedure. LED indicator will flash for 3 seconds and then flash x6 slowly to
indicate successful unpairing.
Step 4: Press and Hold power button until LED indicator turns on.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>