ALL LED AiQ-RLY400B-LN Intelligent Lighting Control Installation Guide
- June 28, 2024
- ALL LED
Table of Contents
INSTALLATION GUIDE
Smart-E
AiQ/RLY400B/LN
Technical Specifications
| Product Code | AiQ/RLY400B/LN |
|---|---|
| Operating Voltage (V) | 100-240VAC |
| Input Current (A) | 1.78A |
| Max Output Power (W) | 400W (HALOGEN); 250W (LED) |
| Output Current (Max) | 1.8A max |
| Output Voltage (Max) | 100-240VAC |
| PF | 0.99 |
| Efficiency % | 94% |
| Network Standby Power (W) | 0.1W |
| Class | II |
| Body Material | White Polymer |
| Ingress Protection | IP20 |
| Ambient Operating Temperature (°C) | -20°C ~ +50°C |
| Guarantee | 5 Years |
| Minimum Load | <1W |
Returns & Faulty Items
- If any problem is encountered during or after installation, please call the ALL LED technical department to get the problem resolved as soon as possible.
- Please do not just return the item to the outlet you purchased it from, as you are only entitled to a replacement or refund after the unit has undergone testing and the unit has been confirmed as having a manufacturing defect/fault. Your statutory rights are not affected.
- The manufacturer will not be deemed liable or held responsible for any damages caused by faults or manufacturing defects that may be present in any of its products or the misuse or incorrect installation of this device. Please refer to our troubleshooting guide for further information.
- All goods are supplied under the terms and conditions of ALL LED LTD, a copy of which may be obtained upon written request.
General Information
- Interference may occur with other products on the same frequency of 2.4Ghz
- Product may differ in colour from image on box
- Range signal can be reduced when using within materials such as concrete & metal
Pairing Instructions
Initial programming of an entire system can be done as simply as: Fusebox
Lighting Breakers OFF (5 Seconds), then ON.
Say “Alexa, add a device” or search on relevant app.
After the device has been added to a network successfully, a 3 minute window
will open for find and bind (for remotes)
Network Mode: 60 Seconds
Find and Bind (for remotes): 3 Minutes
If the 1 minute window elapses, simply switch the module on and off. It will
enter network pairing mode again.
Network Pairing Mode:
This will automatically happen when the product is first switched on.
This mode enables the user to connect the smart module to a network
hub/gateway. This mode will last 1 minute or until a connection has been
established. If successful, the lights will flash. Once the time limit has
elapsed, the module will go into a normal state, with a 3 minute window to
pair any remotes. Once added to a network, the module must be factory reset if
the network must be changed.
Find and Bind Pairing Mode (Remote Control):
Note: If using the items on a smart device, you MUST pair the module and
remote to the hub
PRIOR to pairing with any remote control.
If using the module directly with a remote, you may proceed as below.
To set to this mode toggle the switch rapidly 4 times
From ON – OFF>ON>OFF>ON
Or push the program button on the module 4 times.
The pairing mode enables the user to connect or to disconnect from a remote
device such as a handheld remote. The mode will only last up to 3 minutes or
until the connection has been established. If successful, the lights will
flash.
Factory Reset:
To set to this mode toggle the switch rapidly 7 times
From ON – OFF>ON>OFF>ON>OFF>ON>OFF
Or push the program button on the module 7 times.
Factory reset mode will remove all paired connections to the module. If
successful, the lights will flash. After the reset has completed the module
automatically goes into network pairing mode.
Dimensions
Wiring Diagram
Environmental Protection Waste electrical products should not be disposed of
with household waste. Please recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice
ISOLATE MAINS SUPPLY BEFORE HANDLING ANY ELECTRICAL PRODUCTS The manufacturer
will not be deemed liable or held responsible for any damages caused by faults
or manufacturing defects that may be present in any of its products or the
misuse or incorrect installation of this device
Your statutory rights are not affected.
https://qr.page/g/3TvJf8wf5Oh
ALL LED LTD
42 Sedgwick Road,
Luton, LU4 9DT
www.allledgroup.com
sales@allledgroup.com
Tel: +44 (0)208 841 9000
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>