ALL LED AiQ-DIM400M-LL Intelligent Lighting Control Installation Guide
- June 5, 2024
- ALL LED
Table of Contents
ALL LED AiQ-DIM400M-LL Intelligent Lighting Control
Product Information
Technical Specifications
- Product Name: Smart-R AiQ/DIM400M/LL Dimmable Live/Live – Screw Terminal Module
- Manufacturer: ALL LED LTD
- Model: DIM400M/LL
Frequently Asked Questions
- Q: What should I do if my product is faulty?
- A: In case of a faulty product, please contact our customer support at +44 (0)208 841 9000 or email us at [email protected] for assistance with returns and replacements.
PLEASE READ BEFORE USE!
Technical Specifications
| Product Code | AiQ/DIM400M/LL |
|---|---|
| Operating Voltage (V) | 100-240VAC |
| Input Current (A) Max | 1.84A Max |
| Max Output Power (W) | 400W (Halogen); 250W (LED) |
| Output Voltage (Max) | 100-240VAC |
| PF | 0.99 |
| Efficiency % | 94% |
| Network Standby Power (W) | 0.37W |
| Class | II |
| Body Material | White Polymer |
| Ingress Protection | IP20 |
| Ambient Operating Temperature (°C) | -20°C ~ +50°C |
| Guarantee | 5 Years |
| Minimum Load* | 7W |
*May Require Load Stabiliser if <7W
Pairing Instructions
Initial programming of an entire system can be done as simply as: Fusebox
Lighting Breakers OFF (5 Seconds), then ON.
Say “Alexa, add a device” or search on relevant app.
After the device has been added to a network successfully, a 3 minute window
will open for find and bind (for remotes)
- Network Mode: 60 Seconds
- Find and Bind (for remotes): 3 Minutes
If the 1 minute window elapses, simply switch the module on and off. It will enter network pairing mode again.
Network Pairing Mode
This will automatically happen when the product is first switched on.
This mode enables the user to connect the smart module to a network
hub/gateway. This mode will last 1 minute or until a connection has been
established. If successful, the lights will flash. Oncethe time limit has
elapsed, the module will go into a normal state, with a 3 minute window to
pairany remotes. Once added to a network, the module must be factory reset if
the network must be changed.
Find and Bind Pairing Mode (Remote Control):
Note
- If using the items on a smart device, you MUST pair the module and remote to the hub PRIOR to pairing with any remote control.
If using the module directly with a remote, you may proceed as below
- To set to this mode toggle the switch rapidly 4 times
- From ON – OFF>ON>OFF>ON
- Or push the program button on the module 4 times.
- The pairing mode enables the user to connect or to disconnect from a remote device such as a handheld remote. The mode will only last up to 3 minutes or until the connection has been established. If successful, the lights will flash.
Factory Reset:
- To set to this mode toggle the switch rapidly 7 times
- From ON – OFF>ON>OFF>ON>OFF>ON>OFF
- Or push the program button on the module 7 times.
- Factory reset mode will remove all paired connections to the module. If successful, the lights will fl ash. After the reset has completed the module automatically goes into network pairing mode.
Dimensions
Wiring Diagrams
For Mains Wired Light Switch
**For Low Voltage Light Switch***
- This option should be used with 1 switch only.
- For 2 way switching follow mains option.
Returns & Faulty Items
- If any problem is encountered during or after installation, please call the All LED technical department to get the problem resolved as soon as possible.
- Please do not just return the item to the outlet you purchased it from, as you are only entitled to a replacement or refund after the unit has undergone testing and the unit has been confirmed as having a manufacturing defect/fault. Your statutory rights are not affected.
- The manufacturer will not be deemed liable or held responsible for any damages caused by faults or manufacturing defects that may be present in any of its products or the misuse or incorrect installation of this device. Please refer to our troubleshooting guide for further information.
- All goods are supplied under the terms and conditions of All LED LTD, a copy of which may be obtained upon written request.
General Information
- Interference may occur with other products on the same frequency of 2.4Ghz
- Product may differ in colour from image on box
- Range signal can be reduced when using within materials such as concrete & metal
Environmental Protection
Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice
Warning
- ISOLATE MAINS SUPPLY BEFORE HANDLING ANY ELECTRICAL PRODUCTS
Guarantee
- 5 year Guarantee
The manufacturer will not be deemed liable or held responsible for any damages
caused by faults or manufacturing defects that may be present in any of its
products or the misuse or incorrect installation of this device
Your statutory rights are not affected.
Contact
ALL LED LTD
- 42 Sedgwick Road, Luton, LU4 9DT
- www.allledgroup.com
- [email protected]
- Tel: +44 (0)208 841 9000
Scan
Documents / Resources
| ALL
LED AiQ-DIM400M-LL Intelligent Lighting
Control
[pdf] Installation Guide
AiQ-DIM400M-LL Intelligent Lighting Control, AiQ-DIM400M-LL, Intelligent
Lighting Control, Lighting Control, Control
---|---