ALL LED AIQ DWC WH IQ Intelligent Smart Control Wireless Door Window Sensor Installation Guide
- September 12, 2024
- ALL LED
Table of Contents
AIQ DWC WH IQ Intelligent Smart Control Wireless Door Window Sensor
“`html
Technical Specifications
- Product Code: AiQ/DWC/WH
- Radio Frequency: IQ Intelligent Smart Control Wireless
- Power Supply: Not specified
- Operating Temperature: Not specified
Product Information
The AiQ/DWC/WH IQ Intelligent Smart Control Wireless Door/Window
Sensor is designed to provide smart control and monitoring of doors
and windows.
Installation Guide
-
Connecting Sensor to Smart Hub:
-
Enter Pairing mode on your smart Hub and follow
instructions. -
Installation Instructions:
-
Stick the double-sided tape on the Sensor and magnet.
-
Peel the protective layer from double-sided tape and stick the
sensor on to the door/window. -
Peel the protective layer from double-sided tape and stick the
magnet on to the door/window. Make sure the magnet is within 10mm
from sensor. -
Press and hold the program button for 5 seconds until the LED
indicator flashes three times. If the sensor has connected
successfully to your smart hub, the LED indicator will rapidly
flash. -
Once connected, the sensor will need to be set up in the Alexa
app under routines or scenes to work with other smart devices.
Please follow Smart Hub instructions.
Factory Reset
- Press and hold the program button for 5 seconds until the LED
indicator flashes three times.
FAQ
Q: What should I do if the LED indicator does not flash
as expected during setup?
A: If the LED indicator does not flash as
expected, please ensure that the sensor is within range of the
smart hub and follow the pairing instructions carefully. You may
also try resetting the sensor and reattempting the setup
process.
“`
Returns & Faulty Items
· If any problem is encountered during or after installation, please call the
All LED technical department to get the problem resolved as soon as possible.
· Please do not just return the item to the outlet you purchased it from, as
you are only entitled to a replacement or refund after the unit has undergone
testing and the unit has been confirmed as having a manufacturing
defect/fault. Your statutory rights are not affected.
· The manufacturer will not be deemed liable or held responsible for any
damages caused by faults or manufacturing defects that may be present in any
of its products or the misuse or incorrect installation of this device. Please
refer to our troubleshooting guide for further information.
· All goods are supplied under the terms and conditions of All LED LTD, a copy
of which may be obtained upon written request.
General Information
· Interference may occur with other products on the same frequency of 2.4Ghz ·
Product may differ in colour from image on box · Range signal can be reduced
when using within materials such as concrete & metal
INSTALLATION GUIDE
AiQ/DWC/WH IQ Intelligent Smart Control Wireless Door/Window Sensor
Technical Specifications
Product Code Radio Frequency Power Supply Operating Temperature
AiQ/DWC/WH 2.4Ghz 3VDC (2x CR2450 Batteries) 0°C ~ +40°C
!
PLEASE READ BEFORE USE!
Dimensions
ALL LED LTD 42 Sedgwick Road,
Luton, LU4 9DT
Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice
www.allledgroup.com sales@allledgroup.com Tel: +44 (0)208 841 9000
The manufacturer will not be deemed liable or held responsible for any damages
caused by faults or manufacturing defects that may be present in any of its products
or the misuse or incorrect installation of this device
Your statutory rights are not affected.
1
Connecting Sensor to Smart Hub
1. Enter Pairing mode on your smart Hub and follow instructions.
Installation Instructions
1. Stick the double-sided tape on the Sensor and magnet. 2. Peel the
protective layer from double sided tape and stick the sensor on to the
door/window 3. Peel the protective layer from double sided tape and stick the
magnet on to the door/window.
Make sure the magnet is within 10mm from sensor.
2. Press and hold the program button for 5 seconds until the LED indicator
flashes three times. If the sensor has connected successful to your smart hub
the LED indicator will rapidly flash.
3. Once connected the sensor will need to be setup in the Alexa app under
routines or scenes to work with other smart devices. Please follow Smart Hub
instructions.
Factory Reset
1. Press and hold the program button for 5s until the LED indicator flashes
three times.
2
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>