ALL LED ASC-WIFI-RMT-CCT 4 Zone CCT Remote Control User Manual
- June 29, 2024
- ALL LED
Table of Contents
ASC-WIFI-RMT-CCT 4 Zone CCT Remote Control
“`html
Technical Specifications
- Product Code: ASC/WIFI/RMT/CCT
- Output Power Supply: N/A
- Operating Temperature: N/A
- Dimensions:
- Front view: 137mm x 39mm x 15mm
- Side view: 98mm
- Range: N/A
Safety & Warnings
Ensure power supply is off when handling any electrical
equipment. For further advice, contact ALL LED.
Installation Guide
RF CCT Controller
Pair with RF Receiver
-
Step 1: Install the RF receiver according to the wiring
diagram. -
Step 2: Click the Learning Key button on RF receiver.
-
Step 3: Choose and click a zone number (e.g., zone 4).
-
Step 4: Click any of the four buttons CW WW (e.g., WW), LED
lights connected with the RF receiver flicker once, indicating
successful pairing with zone 4.
RF Signal
RF LED Receiver
Learning Key
Note: One receiver can be paired with a maximum of 8 remote
controls.
Function Introduction
-
On/Off: Control the receiver’s CW channel.
Press and hold down to adjust light intensity. -
Color/Scene Setting: Press and hold down to
save color/scene, click to recall the saved. -
Light Intensity Adjustment: Press and hold
down to increase light intensity smoothly. -
Control WW Channel: Press and hold down to
adjust light intensity. -
Running Mode: Click to play/pause running mode
from Warm White to Cool White. -
Zones: 4 zones, click to choose a zone, press
and hold down to turn ON/OFF corresponding zone.
Troubleshooting Guide
| Problem | Cause(s) | Solution(s) |
|---|---|---|
| No power to drive components. | A qualified installer/electrician should check |
the Primary
voltage side of the product to check the input voltage.| N/A
No Light Coming From LED’s| Loose connection on primary side.
Loose or switched connection/polarity on secondary side.| Ensure continuous
and correct connection between
terminals.
Ensure the polarity is correct; (Red = +, Black = -).
No output from the driver.| Driver may be faulty and require replacement.| N/A
LED’s Flashing| Overvoltage may have caused damage to the sensitive LED drive
components.
Unstable or incorrect input voltage.| Please only use a stable voltage supply
as stipulated earlier
for this product. Failure to do so will void the warranty.
Frequently Asked Questions (FAQ)
Q: How many remote controls can be paired with one
receiver?
A: One receiver can be paired with a maximum of 8 remote
controls.
Q: What should I do if the LED lights are not pairing with the
RF receiver?
A: Ensure that you follow the pairing steps correctly and that
there are no obstructions interfering with the signal between the
remote and the receiver.
“`
Safety
· Do not cover the ground contact. · Do not place any material over the lens
or LED diode/chip. · Do not insert objects into the luminaire. · Do not clean
using any solvent based abrasive or aggressive product. · Do not pull any
cables connected to the product. · Do not direct the luminaire into a persons
eyes, as this unit may have an intense light output,
which if incorrectly used may cause eye damage. · Light engines/LED’S and
other light sources may heat up, please take care when handling the
products. · The manufacturer will not be deemed liable or held responsible for
any damages caused by
faults or manufacturing defects that may be present in any of its products or
the misuse or incorrect installation of this device. Please refer to our
trouble shooting guide for further information. · The manufacturer will not be
held liable for any death(s) or injuries caused by misuse or poor installation
or any unreported faults of this product version or versions thereof. · LED’s
are sensitive to electrostatic discharge. Do not touch the surface of the LED
module. · Do not connect to a temporary electricity supply, this may damage
the electronics. · Light fittings with an integrated emergency option are with
a separate installation and wiring leaflet. Please refer to this manual for
further details. If the manual is unavailable please contact an ALL LED
representative for assistance.
Returns & Faulty Items
· If any problem is encountered during or after installation, please call ALL
LED technical department to get the problem resolved ASAP.
· Please do not just return the item to the outlet you purchased it from, as
you are only entitled to a replacement or refund after the unit has undergone
testing and the unit has been confirmed as having a manufacturing
defect/fault. Your statutory rights are not affected.
· The manufacturer will not be deemed liable or held responsible for any
damages caused by faults or manufacturing defects that may be present in any
of its products or the misuse or incorrect installation of this device. Please
refer to our trouble shooting guide for further information.
· All goods are supplied under the terms and conditions of ALL LED LTD, a copy
of which may be obtained upon written request.
Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice
G
………… E …………
3UARANTE
…. YEAR
This product supplied with a limited 3 year guarantee, subject to terms and
conditions. The manufacturer will not be deemed liable or held responsible for
any damages caused by faults or manufacturing defects that may be present in
any of its products or the misuse
or incorrect installation of this device Your statuatory rights are not
affected.
….
INSTALLATION GUIDE & USER MANUAL ASC/WIFI/RMT/CCT
!
PLEASE READ BEFORE USE!
WARNING
ENSURE POWER SUPPLY IS OFF WHEN HANDLING ANY ELECTRICAL EQUIPMENT
· This product may need to be installed by a qualified electrical installer. ·
Please read this guide in its entirety to fully understand the products before
attempting any
install. · All electrical work should be completed in accordance with the
latest IET regulations, and/
or any other relevant rules, regulations or laws of the country in which it is
being installed. · The item must be installed in isolation from any insulating
material and is adequately
ventilated to prevent premature failure. · Ensure power supply is isolated
prior to installation, maintenance or performing any other
form of electrical work. · In the event of incorrect or improper function with
specific regard to any of ALL LED’s
products and contact ALL LED for further advice.
Technical Specifications
Product Code
Output Power Supply Operating Temperature Dimensions Range
ASC/WIFI/RMT/CCT
RF Signal 3V (1x CR2025 battery) 0-40°C 137 x 39 x 11mm 30m Uninterrupted
Safety & Warnings
· Stored and dispose of properly. · DO NOT expose the device to moisture. · DO
NOT use near or through Metal Mesh as it may effect range.
Dimensions
137mm
39mm
15mm
98mm
Front view
Side view
1
RF CCT Controller
Pair with RF Receiver
Step 1: Install the RF receiver according to wiring diagram (please refer to
the instruction of RF receiver that you would like to pair with.
Step 2: Click the “Learning Key” button on RF receiver
Step 3: Choose and click a zone number (e.g. zone 4)
Step 4: Click any of the four buttons CW WW (e.g. WW), LED lights connected
with the RF receiver flicker once means the receiver is paired with zone 4
successfully.
RF SIGNAL
RF LED Receiver
Leaning Key
Note: one receiver can be paired with max 8 remote controls.
Operate the remote after pairing Click the paired zone number/numbers, then click the other buttons to do the controlling
Function introduction
On/Off Control the receiver’s cw channel, Press and hold down to
increase/decrease light intensity
Press and hold down to save color/scene, click to recall the saved
Press and hold down to increase light intensity smoothly
Control the receiver’s ww channel, Press and hold down to increase/ decrease
light intensity
Press and hold down to decrease light intensity smoothly Click to play/pause
running mode from Warm White to Cool White
4 zones, click to choose a zone, press and hold down to turn ON/OFF corresponding zone
Front side Back side
Note: Before the first use, please remove the protective film on. the battery.
Troubleshooting Guide
PROBLEM
CAUSE(S)
SOLUTION(S)
No power to drive components.
A qualified installer/electrician should check the Primary voltage side of the product to check the input voltage.
No Light Coming From LED’s
Loose connection on primary side.
Ensure continuous and correct connection between terminals.
Loose or switched connection/ polarity on secondary side.
Ensure continuous and correct connection between terminals. Ensure the polarity is correct; (Red = +, Black = -).
No output from the driver.
Driver may be faulty and require replacement.
LED’s Flashing
Over voltage may have caused damage to the sensitive LED drive components.
These cases are rare and the item may need replacement and/or investigation as to the cause of failure.
Unstable or incorrect input voltage.
Please only use a stable voltage supply as stipulated earlier for this product. Failure to do so will void the warranty.
LED driver may be connected to a dimmer switch
Please remove the dimmer switch. Use of this product on a dimmer will void the warranty. This product is supplied nondimmable as standard.
Loose connection on primary side.
Ensure continuous and correct connection between the terminals.
Loose connection on secondary side.
Ensure continuous and correct connection between terminals. Ensure the polarity is correct; (Red = +, Black = -).
ATTENTION
IF ANY PROBLEMS PERSIST, PLEASE CALL THE ALL LED TECHNICAL DEPARTMENT FOR
FURTHER ASSISTANCE.
3
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>