ALL LED AIQ-4Z-RMT Mono 4 Zone Smart Remote Control Installation Guide

: September 28, 2024
: ALL LED

Table of Contents

AIQ-4Z-RMT Mono 4 Zone Smart Remote Control
Specifications:
Product Usage Instructions:
Quick Install Guide:
- Option 1: Connecting Your Remote to a Smart Home Hub
- Option 2: Connecting Your Remote to Intelligent Lighting
Factory Reset Remote:

AIQ-4Z-RMT Mono 4 Zone Smart Remote Control

“`html

Specifications:

Product Code: AiQ/4Z/RMT
Protocol: ZigBee 3.0
Operating Voltage: 3VDC
Battery Type: CR2032 x1
Transmission Frequency: 2.4 GHz
Transmission Range (Uninterrupted): 30 m
Ingress Protection: IP20

Product Usage Instructions:

Quick Install Guide:

To use the remote with your Smart Home Hub and lighting devices,
follow either Option 1 or Option 2. If using the remote directly
with your lighting control devices without a Hub, follow Option
2.

Option 1: Connecting Your Remote to a Smart Home Hub

From your smart home hub interface, select to add a device and
enter pairing mode.
Press and hold down the All On button until the LED indicator
turns on.
Immediately press the All Off button. The LED indicator will
flash. After 20 seconds, the remote will time out. A quick triple
blink indicates successful pairing.

Option 2: Connecting Your Remote to Intelligent Lighting

Control Devices

Set the receiving device to Find and Bind mode. The lights will
flash to indicate active mode for 3 minutes.
Bring the remote within 10 cm of the lighting device within the
active duration.
Short press the ON button of the desired group (1-4) to select
a group for pairing.
Press and hold down the All ON button until the LED indicator
turns on.
Immediately press group 1 ON button to start pairing. The LED
indicator will flash fast for 3 seconds, then flash slowly six
times to indicate successful pairing.

Factory Reset Remote:

If unsuccessful in pairing, factory reset the remote by pressing
and holding down the All ON button until LED indicator turns on,
then pressing All Off button.

FAQ:

Q: What should I do if the LED indicator does not blink as

expected during pairing?

A: If the LED indicator does not blink as expected during
pairing, perform a factory reset of the remote and try again.

Q: How many scenes can I save per group with this remote?

A: You can save up to 2 scenes per group using this remote.

Q: What is the transmission range of this remote?

A: The uninterrupted transmission range of this remote is 30
meters.

“`

Dimensions

Returns & Faulty Items
· If any problem is encountered during or after installation, please call the All LED technical department to get the problem resolved as soon as possible.
· Please do not just return the item to the outlet you purchased it from, as you are only entitled to a replacement or refund after the unit has undergone testing and the unit has been confirmed as having a manufacturing defect/fault. Your statutory rights are not affected.
· The manufacturer will not be deemed liable or held responsible for any damages caused by faults or manufacturing defects that may be present in any of its products or the misuse or incorrect installation of this device. Please refer to our troubleshooting guide for further information.
· All goods are supplied under the terms and conditions of All LED LTD, a copy of which may be obtained upon written request.

Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice

The manufacturer will not be deemed liable or held responsible for any damages caused by faults or manufacturing defects that may be present in any of its products
or the misuse or incorrect installation of this device Your statutory rights are not affected.

ALL LED LTD 42 Sedgwick Road,
Luton, LU4 9DT
www.allledgroup.com sales@allledgroup.com Tel: +44 (0)208 841 9000

INSTALLATION GUIDE MONO SMART REMOTE
AiQ/4Z/RMT 4 Zone Smart Remote Control

!
PLEASE READ BEFORE USE!

All ON Button: Click to turn on all paired lighting devices.
Press and hold down to search and pair to Smart Home Hub or to factory reset the remote.

All OFF Button: Click to turn off all paired lighting devices.

Group 1-4 ON buttons, click to turn on all the paired lighting devices to this group, press and hold down to dim lights up.
Note: This remote supports 4 groups for binding a max. of 30 lighting devices and enables saving 2 scenes per group.

Group 1-4 OFF buttons, click to turn off all the paired lighting devices to this group, press and hold down to dim light down.
2 scene buttons. Press and hold down to save a scene or click to recall the saved scene.

Product Code Protocol Operating Voltage Battery Type Transmission Frequency Transmission Range (Uninterrupted) Ingress Protection

Front Side
AiQ/4Z/RMT ZigBee 3.0 3VDC CR2032 x1 2.4 GHz 30 m IP20

Magnetic Bracket

Note: Before the first use, please remove the protective film on the battery
1

Quick Install Guide
To be able to use a remote with your Smart Home Hub and intelligent lighting devices follow (Option 1 and Option 2). If you would like to use your remote directly with your intelligent lighting control devices without a Hub, follow instructions (Option 2). Remove protective film on battery before first use.
Option 1: Connecting Your Remote to a Smart Home Hub e.g. Alexa Echo LED Indicator
Step 1: From your smart home hub interface, choose to add a device or accessory and enter pairing mode as instructed below.
Step 2: Press and hold down All On button until LED indicator turns on.
Step 3: Immediately short press the All Off button. The LED indicator will flash. After 20 seconds the remote will time out. LED indicator will then blink x3 quickly for successful pairing.

Note: If unsuccessful, factory reset (as below) and try again.

Option 2) Connecting your remote to Intelligent lighting control devices.

Step 1: Set receiving device to Find and Bind mode. Lights will flash indicating Find and Bind mode active: Duration 3 minutes.

LED Indicator
Step 2: Bring the remote within 10 cm of the intelligent lighting device. 3 minutes until timeout.

Step 3: Short press the ON button of group 1, 2, 3 or 4 to choose a group that you would like to pair the device to. CARE: Select Zone First Step 4: Press and hold down All ON button until LED indicator turns on.
Factory Reset Remote

Step 5: Immediately short press group 1 ON button to start pairing the remote. The LED indicator will flash fast for 3 seconds to start find and bind pairing and then flash x6 slowly to indicate successful pairing to the device.
Note: If unsuccessful, factory reset (as below) and try again.

Step 1: Press and hold down the ALL ON button until LED indicator turns on.

Step 2: Immediately short press the same button x5 continuously, LED indicator will flash x3 quickly to indicate successful reset.

LED Indicator
Note: All configuration parameters will be reset after the remote is reset or removed from the network.
2

Remove Paired Devices

Removing An Intelligent Lighting Control Device From Your Remote

Step 1: Set receiving device to Find and Bind mode. Lights will flash indicating Find and Bind mode active: Duration 3 minutes.

LED Indicator
Step 2: Bring the remote within 10 cm of the intelligent lighting device. 3 minutes until timeout.

Step 3: Short press the ON button of group 1, 2, 3 or 4 to choose a group that you would like to pair the device to. CARE: Select Zone First
Step 4: Press and hold down All ON button until LED indicator turns on.

Step 5: Immediately short press group 1 ON button twice to start pairing the remote. The LED indicator will flash fast for 3 seconds to start find and unbind pairing and then flash x6 slowly to indicate successful unpairing to the device.

Scenes
How To Save Scenes
Step 1: Make sure that lighting devices have already been paired to any of the 4 groups that you would like to save scenes for.
Step 3: Press and hold down a scene button (e.g. S1) until LED indicator flashes to confirm the brightness for this group has been saved. CARE: Select Zone First

LED Indicator
Step 2: Press and hold the ON or OFF button of the desired group to adjust the brightness for each individual group.
Step 4: Repeat Step 3 if you want to save another scene to (S2).

How to Recall Saved Scenes Step 1: Short press either the S1 or S2 buttons to recall a saved scene for each individual group.