cell2 AK Standard LED Light Bars Instructions

cell2 AK Standard LED Light Bars

INSTRUCTION MANUAL

WIRING & FUNCTIONS

(BL/BO-Single/Dual Color -SAE) I (BE/BF -Single/Dual Color-ECE R65/R10)

Proper installation of the product requires the installer to have a good understanding of automotive electronics, systems and procedures. Different applications may require different functions. For optimum efficiency, it is highly recommended to determine, configure and test the required functions prior to installation.

LIGHTBAR WIRING

POWER CABLE

1. Route power wires to the vehicle firewall towards the battery.
2. Install a fuse (user-supplied) to the end of the RED wire and connect it to the battery. (for correct fuse rating, refer to the Lightbar Specs.)
3. Connect the BLACK wire to the vehicle chassis-ground next to the battery.

NOTE: Ensure that all wires of the power cable are firmly connected to the power source.

WARNING

• DO NOT USE THE POWER WIRE(S) AS THE LIGHTBAR ACTIVATION SWITCH. USE ONLY THE FUNCTION WIRE(S) TO SWITCH AND ACTIVATE.
• ENSURE THE POWER WIRE(S) ARE PROPERLY CONNECTED BEFORE ACTIVATING ANY FUNCTION WIRE(S).
• FAULTY CONNECTIONS MAY CAUSE THE LIGHTBAR TO MALFUNCTION AND/ OR RESET TO ITS DEFAULT SETTINGS.
• DO NOT USE A HIGH PRESSURE POWER WASHER TO CLEAN YOUR LIGHTBAR; THIS MAY DAMAGE YOUR LIGHTBAR AND VOID ITS WARRANTY.

FUNCTION WIRES (Input)

Connect each individual function wire to its switch.

WARNING MODE 1 & MODE 2 & MODE 3

1. Activate the desired Mode by applying +VDC to BROWN, ORANGE or WHITE wire.
■ BROWN wire for Warning Mode 3.
■ ORANGE wire for Warning Mode 2.
■ WHITE wire for Warning Mode 1 (Cruise Mode).

NOTE: If the lightbar is equipped with Dual Color lightheads, Warning Mode 2 will display in Color 2.

2. Each of the Warning Modes can select and store one pattern from the built- in flash patterns.
To change flash pattern:
i. While a Warning Mode is activated, tap +VDC to YELLOW wire:
a. Once to next pattern. (refer to Flash Pattern chart)
b. Quick 3 times to FP#1.
3. If a steady-bum pattern (cruise mode) is selected, number of activated lightheads can be set differently based on the user’s application requirment. (by default, only Corner Section will be activated)
To change the activated lightheads during a cruise mode:
i. Activate a Warning Mode with its flash pattern selected to an steady-burn (cruise mode) pattern.
ii. While the Warning Mode is activated, tap +VDC to GRAY wire quickly once to progressively scroll through different number of lightheads.

Flash Patterns

TAKE-DOWN & ALLEY LIGHT

Activate Take-Down & Alley(Corner) Lights in High Power steady-burn by applying the GREEN wire to +VDC. By default, Take-Down Lights are set at the second lightheads from the center of the lightbar. Alley lights are set at all three corner lights.

NOTE: If the lightbar is equipped with Dual Color lightheads,

Take-down and Alley will display in Color 2.
To re-designate preferred Illuminated areas, tap +VDC to YELLOW wire while the Take-Down & Alley (Corner) Lights mode is on.

• Quick once to the next Illuminated areas. (refer to Illuminated Area chart).
• Quickly 3 times to reset to IA#1.

TRAFFIC ARROW

Activate rear Traffic Arrow function by applying

• BLUE wire to +VDC for Left Arrow.
• PURPLE wire to +VDC for Right Arrow.
• Above 2 wires together to +VDC for Centre-out Arrow.

NOTE: If the lightbar is equipped with rear Dual Color lightheads,

Traffic Arrow will display in Color 2.
To configure the Traffic Arrow flash pattern, tap +VDC to YELLOW wire while in a Traffic Arrow mode:
a. Once to next pattern. (refer to Traffic Arrow Pattern chart).
b. Quick 3 times to TP#1.

LOW POWER OPERATION I MANUAL DIM FUNCTION

Activate warning mode Low Power Operation by continuously applying +VDC to GRAY wire.

NOTE: Dim Mode is not applicable for flash patterns with ICAO, steady and pulsing pattern marked with * in Flash Pattern table.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>