Cell2 BB Raiden Fit Instruction Manual

: September 24, 2024
: Cell2

Table of Contents

Cell2 BB Raiden Fit
Product Information
Product Usage Instructions
FAQ
WIRING & FUNCTIONS
Flash Patterns
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Cell2 BB Raiden Fit

Product Information

Specifications

Model: AL-SAE / AE-ECE R65
Power Supply: +VDC
Color Coding: RED (+VDC), BLACK (Chassis Ground), WHITE (Warning Mode), YELLOW (Dim Mode/Cruise Mode)

Product Usage Instructions

Wiring Instructions

Route the power cable’s RED wire to the battery and install the appropriate fuse close to the battery end.
Connect the BLACK wire to the vehicle chassis ground.
Pass control wires through the firewall, ensuring no damage to components.
Route control wires to a switch panel in the dash area and connect as needed.
Ensure all power cable wires are securely connected to the power source.

Warning:

Do not use power wires as the lightbar activation switch.
Use only the function wires to switch and activate to prevent malfunction or resetting to default settings. Avoid using high-pressure power washers for cleaning.

Warning Mode Activation:

To activate Warning Mode, apply +VDC to the WHITE wire. Change flash patterns by tapping +VDC to the YELLOW wire while Warning Mode is ON.

Dim Mode / Manual Dim:

Apply +VDC constantly to the YELLOW wire while in Warning Mode for dimming functionality.

Cruise Mode Activation:

Activate Cruise Mode by applying +VDC constantly to the YELLOW wire. Cruise Mode can only be triggered when Warning Mode is OFF.

FAQ

Q: What should I do if the lightbar malfunctions?
- A: Check for faulty connections and ensure correct wiring. Avoid using high-pressure power washers for cleaning as it may damage the lightbar.

WIRING & FUNCTIONS

WIRING & FUNCTIONS (AL-SAE / AE-ECE R65)

Proper installation of the product requires the installer to have a good understanding of automotive electronics, systems and procedures. Different applications may require different functions. For optimum efficiency, it is highly recommended to determine, configure and test the required functions prior to Installation.

LIGHTBAR WIRING

[Px] = Order of Precedence. When more than one wire are activated at the same time, the wire with the higher precedence will override/affect the performance of the lower precedence wire. P1 being the highest order.

WIRING

Route power cable’s RED wire to battery and make sure the fuse (user-supplied) is properly installed on the red wire close to the battery end.
Connect the BLACK wire to the vehicle chassis ground.
Follow factory wiring harness through the firewall. It may be necessary to drill a hole in the firewall. Ensure that there is no component that could be damaged from the drilling.
Route control wires towards the dash area to a switch panel (user-supplied). Connect the required wires to the switch panel.
Make sure that all wires of power cable are securely connected to power source.

WARNING

DO NOT USE THE POWER WIRE(S) AS THE LIGHTBAR ACTIVATION SWITCH. USE ONLY THE FUNCTION WIRE(S) TO SWITCH AND ACTIVATE.
FAULTY CONNECTIONS MAY CAUSE THE LIGHTBAR TO MALFUNCTION AND / OR RESET TO ITS DEFAULT SETTINGS.
DO NOT USE A HIGH PRESSURE POWER WASHER TO CLEAN YOUR LIGHTBAR; THIS MAY DAMAGE YOUR LIGHTBAR AND VOID ITS WARRANTY.

WARNING MODE

Activate Warning Mode by applying +VDC to WHITE wire.
To change flash pattern, tap +VDC to YELLOW wire while Warning Mode is ON.
- Quick once to the next pattern.
- Quick 3 times to reset to default flash pattern.

DIM MODE/ MANUAL DIM

Apply YELLOW wire to +VDC constantly while a warning mode is ON.

CRUISE MODE

Active Cruise Mode by applying +VDC constantly to YELLOW wire ; all lightheads will steady burn in low power.

NOTE:

The cruise mode can only be triggered when WARNING MODE is OFF.
When turning ON warning mode in Day time, make sure to check if cruise mode is OFF correctly. Otherwise the warning mode will be triggered in dim mode.

Flash Patterns

FP#| SAE (AL Version)| Grouping| FP#| ECE (AE Version)| Grouping
1| Single [SAE, CA13] (Default)| All| 1| Double (Corners) [R65] (Default)| Corners
2| Double [SAE]| All| 2| Double [2Hz]| All
3| Quad [SAE]| All| 3| Quad [2Hz]| All
4| Quint [SAE]| All| 4| Single [2Hz]| All
5| Mega| All| 5| Triple [2Hz]| All
6| Ultra [SAE]| All| 6| Double [2Hz]| Left-Right
7| Single-Quad| All| 7| Quad [2Hz]| Left-Right
8| Single H/L| All| 8| Single [2Hz]| Left-Right
9| Single-Triple-Quint| All| 9| Triple [2Hz]| Left-Right
10| Single| Left-Right| 10| ICAO Single | Corners
11| Double| Left-Right| 11| Single [1.25Hz] | All
12| Quad| Left-Right|

Dim Mode is not applicable.

NOTE

Actual approval is based on the configuration of the model ordered.

AUTO-DIMMING LIGHT SENSOR

This lightbar is equipped with an Auto-Dimming Light Sensor, Low Power Operation will automatically activate when the ambient brightness is below the set-value (e.g. night time) and deactivate once prior condition is removed. The Auto-Dimming Light Sensor takes precedence over all other function wires.