itel A667L Android Mobile Smart Phone User Manual

September 24, 2024
itel

A667L Android Mobile Smart Phone

“`html

Specifications:

  • Operating System: AndroidTM 14 (Go edition)
  • Display components: LCD
  • Front Camera: X MP
  • Rear Camera: X MP
  • Processor: X GHz Quad-core
  • RAM: X GB
  • Storage: X GB, expandable up to X GB with microSD

Product Usage Instructions:

1. Know your phone:

The phone features a front camera, volume buttons, and a power
button.

2. SIM/SD card installation:

  1. Power off your phone.
  2. Refer to the provided picture for the correct installation of
    the SIM/SD card.

3. Charging the phone:

You can charge your phone using a charger or by connecting it to
a computer with the USB cable provided.

  1. Plug in the cable in the correct orientation.
  2. Use only itel chargers and cables to avoid damaging the phone
    and voiding its warranty.

FCC Caution:

This device complies with Part 15 of the FCC Rules. Any changes
not approved may void the user’s authority to operate the
equipment.

Body-worn Operation:

Maintain a minimum separation distance of 1.0cm between the
user’s body and the handset, including the antenna, for RF exposure
compliance.

Use only supplied or approved antennas to meet RF exposure
requirements.

FAQ:

Q: Can I use any charger to charge my phone?

A: It is recommended to use only itel chargers and cables to
prevent damage to the phone and maintain warranty validity.

Q: How do I install a SIM/SD card?

A: Power off your phone and refer to the provided picture for
correct installation steps.

“`

A667L
User Manual
1

Exploded diagram specification

1 Display components

2 Receiver decoration

3 Shell component

4 Receiver

5 Front camera silicone cover

6 Front Camera

7 Rear camera

8 SIM card holder conductive

sponge

9 Main board

10 Front camera support foam

Myra

11 Main board screws

12 Camera grounding conductive

sponge

13 Front camera support foam

14 SIM card holder

15 Middle frame component

16 Flash cover lens

17 Main camera lens

18 Shell screws

19 Composite board battery cover 20 Fingerprint

21 Rear auxiliary camera

22 Speaker

23 Battery 25 Sub pcba 27 coaxial line 29 Side key FPC
31 Rear auxiliary camera conductive cloth

24 motor 26 USB silicone sleeve 28 Earphone silicone case 30 Rear main camera conductive
sponge 32 Rear secondary camera lens

2

Know your phone

1. Front camera 2. Volume + button 3. Volume – button

4. Power button 3

SIM/SD card installation
1. Power off your phone.
2. Refer to the following picture for SIM/SD card installation.

Charging the phone
You can charge your phone with a charger or by connecting it to a computer using a USB cable (comes with the phone).
1. Please plug in the correct orientation.
2. Use only itel chargers and cables. Other chargers or cables may damage the phone and invalidate its warranty.

FCC Caution
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information: This mobile phone meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: A667L (FCC ID: 2AJMN-A667L) has also been tested against this SAR limit. The highest SAR

value reported under this standard during product certification for use at the ear is 0.807 W/kg and when properly worn on the body is 0.712 W/kg.
Body-worn Operation This device was tested for typical body-worn operations. To
comply with RF exposure requirements, a minimum separation distance of 1.0cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
Operating System: AndroidTM 14 (Go edition) Android is a trademark of Google LLC.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals