itel Vision 3 Smartphone User Manual
- October 30, 2023
- itel
Table of Contents
Vision 3
User Manual
Explosion diagram specification
| 1 | CTP LCM ASSEMBLY | 2 | FRONT SHELL ASSEMBLY |
|---|---|---|---|
| 3 | F CAM RUBBER | 4 | FRONT CAMERA |
| 5 | RECEIVER | 6 | REC CON FB |
| 7 | F CAM COP FOIL | 8 | MAIN PCB |
| 9 | LCM WATERPROOF RUBBER | 10 | BAT FPC CONN RUBBER |
| 11 | R MAIN CAM CON FOAMS | 12 | R CAM CON FB 8W |
| 13 | FM SUPPORT MYLAR | 14 | FM CON FOAMS |
| 15 | FM | 16 | FP SEAL SILICONE LOOP |
| 17 | CAM FF 8M | 18 | CAM FF 8W |
| 19 | R VICE CAM RUBBER | 20 | UP FRAME ASM |
| 21 | UP FRAMEWATERPROOF MYLAR | 22 | R MAIN CAM LENS |
| 23 | R VICE CAM LENS | 24 | R VICE CAM LENS2 |
| 25 | MC SCREW SILVER GIUE | 26 | CARD HOLDER |
| 27 | BAT COVER ASM | 28 | R CAMDECO ASM |
| 29 | MACHINE SCREW BLACK | 30 | SPK FRAMEWATERPROOF MYLAR |
| 31 | USB RUBBER | 32 | EAR PHONE RUBBER |
| 33 | SPK FRAME ASM | 34 | MOTOR |
| 35 | COAXIAL CABLE | 36 | SPK |
| 37 | PCBA SUB | 38 | FPC SIDE KEY |
| 39 | BAT |
Know your phone
- Front camera
- Volume + key
- Volume – key
- Power key
SIM/SD card installation
- Power off mobile.
- Refer to the following picture for SIM / SD card installation.
Charging the phone
You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone).
- Please remind the front and back of the plug.
- Use only itel charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty.
FCC Caution
Labelling requirements.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference. (2) This device must accept any interference received, including
interference that may cause undesired operation.
Information to user.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information:
This mobile phone meets the government’s requirements for exposure to radio
waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluation
of scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6
W/kg averaged over one gram of tissue. Device types: S661LP (FCC ID: 2AJMN-
S661LP) has also been tested against this SAR limit. The highest SAR value
reported under this standard during product certification for use at the ear
is 1.16 W/kg and when properly worn on the body is 0.58 W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of .0 cm must be
maintained between the user’s body and the handset, including the antenna.
Third- party belt-clips, holsters, and similar accessories used by this device
should not contain any metallic components. Body-worn accessories that do not
meet these requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or an approved antenna.
Operating System：Android™
Android is a trademark of Google LLC.