itel P55 128GB + 8GB Smart Phone User Manual
- June 11, 2024
- itel
Table of Contents
itel P55 128GB + 8GB Smart Phone
Product Specifications
- Operating System: AndroidTM
- Front Camera
- Volume + key and Volume – key
- Power key & side fingerprint sensor
- NFC
Product Usage Instructions
SIM/SD Card Installation
- Power off the mobile phone.
- Refer to the provided picture for SIM/SD card installation.
Charging the Phone
To charge your device:
- Use a charger or connect it to a computer using the provided USB cable.
- Only use the itel charger and cables that come with the phone. Using other chargers or cables may cause damage and void the phone warranty.
FCC Caution
This device complies with Part 15 of the FCC Rules. Please adhere to the
following:
- The device should not cause harmful interference.
- The device must accept any interference received, including interference that may cause undesired operation.
- Any changes or modifications not approved by the responsible party could void the user’s authority to operate the equipment.
Specific Absorption Rate (SAR) information: This mobile phone meets the government’s requirements.
Note : AndroidTM is a trademark of Google LLC.
FAQ
-
Q: Can I use any charger to charge the phone?
A: No, only use the itel charger and cables provided with the phone to avoid damaging the device and voiding the warranty. -
Q: How do I insert a SIM or SD card?
A: Power off the phone, then refer to the provided picture for guidance on SIM/SD card installation.
P55
User Manual
Explosion diagram specification
1 | TP+LCD | 2 | RECEIVER DECORATING PART |
---|---|---|---|
3 | FRONT COVER FRAME | 4 | MAIN BOARD |
5 | F CAM | 6 | R CAM 1 |
7 | R CAM 2 | 8 | RECEIVER |
9 | COPPER FOIL D | 10 | COPPER FOIL B |
11 | COPPER FOIL A | 12 | R CAM FOAM |
13 | SIM CARD | 14 | PS LENS RUBBER |
15 | SIDE KEY | 16 | MIDDLE FRAME |
17 | SCREW L3.5 | 18 | BACK FLASHHOOD |
19 | BATTERY COVER FOAM | 20 | BATTERY COVER |
21 | BAT DECO | 22 | R CAM 1 DECORATING PART |
23 | R FLASH DECORATING PART | 24 | LENS 1 |
25 | LENS 3 | 26 | LENS 2 |
27 | R CAM 2 DECORATING PART | 28 | FINGERPRINT FPC |
29 | SCREW L3.2 | 30 | COAXIAL CABLE |
31 | SPEAKER | 32 | MOTOR |
33 | SUB BOARD | 34 | SPK RUBBER |
35 | USB RUBBER | 36 | BATTERY |
37 | SIDEKEY FPC | 38 | NFC |
Know your phone
- Front camera
- Volume + key
- Volume – key
- Power key & side fingerprint sensor
- NFC
SIM/SD card installation
- Power off mobile.
- Refer to the following picture for SIM / SD card installation.
Charging the phone
You can charge your device using a charger or by connecting it to the computer
using a USB cable (comes with the phone).
Use only itel charger and cables. Other chargers or cables may damage the
device. This will invalidate your phone warranty.
FCC Caution
Labelling requirements.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Information to user.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information
This mobile phone meets the government’s requirements for exposure to radio
waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluation
of scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue.
Device types:A666LN(FCC ID:2AJMN-A666LN) has also been tested against this SAR
limit. The highest SAR value reported under this standard during product
certification for use at the ear is 1.31W/kg and when properly worn on the
body is 0.93W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 1.0 cm must be
maintained between the user’s body and the handset, including the antenna.
Third-party belt-clips, holsters, and similar accessories used by this device
should not contain any metallic components. Body-worn accessories that do not
meet these requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or an approved antenna.
Operating System : AndroidTM
Android is a trademark of Google LLC.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>