DENALI HMT.07007-01 Split Horn Mount Instruction Manual

September 23, 2024
DENALI

HMT.07007-01 Split Horn Mount

Product Information

Specifications

  • Bolt Size: M3, M4, M5, M6, M8, M10, M12
  • Torque Specifications:
    • in-lbs: 10.0, 23.0, 44.5, 78.0
    • ft-lbs: 3.5, 6.5, 13.5, 30.0, 52.0
    • Nm: 1.0, 2.5, 5.0, 9.0, 18.0, 41.0, 71.0

Product Usage Instructions

Installation Tips

We strongly recommend using medium strength liquid thread locker
on all screws, nuts, and bolts. Ensure all hardware is tightened to
the specified torque as per the owner’s manual.

Hardware Sizing Guide

Use the ruler provided to measure screws, bolts, spacers, etc.
Measure the length from the start of the mounting surface to the
end of the screw.

Kit Contents

Tools Required: Allen Key Set, Torx Bit set, 13mm Wrench, Torque
Wrench

Mounting Instructions

Mounting Location – Acoustic Unit

Step One: On the clutch side of the bike, 2nd
and 3rd fastener from the bottom. Remove the two T30 torx screws
from the engine case.

Assembling the Bracket

Step One: Using the supplied M6 x 35mm screws,
mount the acoustic unit bracket to the engine case. Torque these
screws to 36in-lbs or 4NM.

Mounting the Bracket and Horn

Step One: Mount the SoundBomb acoustic housing
to the bracket using the hardware supplied with the SoundBomb Horn
Kit.

Mounting Location

Step One: On the clutch side of the bike on the
rear of the clutch side cylinder head. Remove the T30 torx screw
from the engine case shown above.

Assembling the Bracket

Step One: Mount the Compressor Unit to the
bracket using the hardware supplied in the Sound Bomb Kit.

Mounting the Bracket and Horn

Step One: Using the supplied M6 x 45mm screw,
mount the Compressor Unit bracket to the engine case. Torque these
screws to 36in-lbs or 4NM.

FAQ

Q: What should I do if I encounter issues during

installation?

A: If you encounter any difficulties during installation or have
any questions, please contact our gear experts at 401.360.2550 or
visit our website at WWW.DENALIELECTRONICS.COM for assistance.

Instruction Rev00

DENALIELECTRONICS.COM

Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go the extra mile to make sure our instructions are clear and as easy to understand as possible. If you have any questions, comments, or suggestions don’t hesitate to give our gear experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. DENALI takes no responsibility for damages caused by improper installation. Caution: When installing electronics it is extremely important to pay close attention to how wires are routed, especially when mounting products to the front fender, front forks, or fairing of your motorcycle. Always be sure to turn the handlebars fully left, fully right, and fully compress the suspension to ensure the wires will not bind and have enough slack for your motorcycle to operate properly.

Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws, nuts, and bolts. It is also important to ensure that all hardware is tightened to the proper torque specifications as listed in your owner’s manual. For included accessory hardware please refer to the default torque specifications provided below. Inspect all hardware after the first 30 miles to ensure proper torque specifications are maintained.

Bolt Size
M3 M4 M5 M6 M8 M10 M12

in-lbs
10.0 in-lbs 23.0 in-lbs 44.5 in-lbs 78.0 in-lbs

ft-lbs
3.5 ft-lbs 6.5 ft-lbs 13.5 ft-lbs 30.0 ft-lbs 52.0 ft-lbs

Nm
1.0 Nm 2.5 Nm 5.0 Nm 9.0 Nm 18.0 Nm 41.0 Nm 71.0 Nm

Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc. Remember, the length of a screw or bolt is measured from the start of the “mounting
surface” to the end of the screw, so only include the screw head when measuring countersunk screws.

0mm

10

20

30

40

50

60

70

80

90

0in

1

2

3

(d) (a)
(c) (f)
(e) (b)

Kit Contents
(a) Horn Compressor bracket (HMT.07007-01)…………………………Qty 1 (b) M6x45mm Mounting Bolt………………………………………………Qty 1 (c) M6x35mm Mounting Bolt………………………………………………Qty 2 (d) Acoustic Unit Mounting Bracket (HMT.07.11200-02)…………….Qty 1 (e) M6 Washer……………………………………………………………….Qty 3 (f) M6 x 9.5mm spacer…………………………………………………….Qty 1

Tools Required: (a) Allen Key Set (b) Torx Bit set (c) 13mm Wrench (d) Torque Wrench

.

DENALIELECTRONICS.COM

1.1 – Mounting Location – Acoustic Unit
Step One: On the clutch side of the bike, 2nd and 3rd fastener from the bottom. Remove the two T30 torx screws from the engine case.

1.2 – Assembling the Bracket
Step One: Using the supplied M6 x 35mm screws, mount the acoustic unit bracket to the engine case. Torque these screws to 36in-lbs or 4NM.

1.3 – Mounting the Bracket and Horn
Step One: Mount the SoundBomb acoustic housing to the bracket using the hardware supplied with the SoundBomb Horn Kit.

.

DENALIELECTRONICS.COM

2.1 – Mounting Location
Step One: On the clutch side of the bike on the rear of the clutch side cylinder head. Remove the T30 torx screw from the engine case shown above.

2.2 – Assembling the Bracket
Step One: Mount the Compressor Unit to the bracket using the hardware supplied in the Sound Bomb Kit.

2.3 – Mounting the Bracket and Horn
Step One: Using the supplied M6 x 45mm screw, mount the Compressor Unit bracket to the engine case. Torque these screws to 36in-lbs or 4NM.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

DENALI User Manuals

Related Manuals