HYUNDAI HSL122407 Solar Square Pathway Light User Manual
- September 18, 2024
- HYUNDAI
Table of Contents
- PACKAGE CONTENTS
- PLANNING FOR A SUCCESSFUL ASSEMBLY
- CHOOSING THE RIGHT LOCATION
- HOW SOLAR WORKS
- ASSEMBLY AND INSTALLATION
- MAINTENANCE
- CHARGING THE BATTERY
- TROUBLESHOOTING
- CARE & CLEANING
- TECHNICAL SPECIFICATIONS:
- PATENT PENDING
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
HYUNDAI HSL122407 Solar Square Pathway Light User Manual
PACKAGE CONTENTS
A. Solar head with bulb x 2
B. AA 1.2V 1000mAh Ni-Mh rechargeable battery (pre-installed) x 2
C. Housing x 2
D. Post x 6
E. Post connector x 4
F. Stake x 2
PLANNING FOR A SUCCESSFUL ASSEMBLY
- Read all instructions before assembly and installation.
- Inspect each part for defects that may have occurred during shipping.
- Keep your receipt these instructions for proof of purchase.
CHOOSING THE RIGHT LOCATION
Install your solar light in a location with full, direct sunlight. Do not install in shaded areas as these areas will not allow the batteries to fully charge and will reduce the nighttime operating hours for your light. Ensure that the installation location is away from other nighttime light sources such as street or porch lamps. These light sources may prevent your solar light from automatically turning on.
HOW SOLAR WORKS
The solar light has a solar panel that converts sunlight into electricity.
During the day, the converted electricity is stored in the rechargeable
batteries. At night, the solar light is powered by the batteries using the
electricity stored during the day.
The operating time depends on geographical location, daily weather conditions,
and season. For optimal performance during the evening, allow the batteries to
charge for 6 to 7 hours in direct sunlight.
ASSEMBLY AND INSTALLATION
-
Preparing For Installation
NOTE : The solar panel will automatically turn the light on at dusk.- FOR FIRST TIME USE: Twist and remove the solar head (A) from the housing (C).
- Push the button (a) to the ON position.
- Replace the solar head (A) on the housing (C), twist to lock into place.
- Put the housing (C) connector into the post (D), put the post connector (E) into the post (D). Repeat to get the desired height of torch.
- Firmly slide the stake (F) into the post (D).
-
Installing the solar light in the ground
NOTE : Do not use a hammer. If the ground is hard, use water to soften it or a trowel to loosen the soil.- Push the assembly firmly into the ground.
- Choose the desired height of the post to assembly
MAINTENANCE
Replacing the battery
- CAUTION : When replacing the battery, use one 1000 mAh NiMH AA 1.2V rechargeable battery.
- IMPORTANT: Dispose of the batteries in accordance with local, state, and federal regulations.
- NOTE : For best performance, replace with a rechargable 1.2V AA NiMH battery of 1000 mAh or greater every 3 years or when performance diminishes.
1. Remove the screws on the solar head (A) to remove.
2. Replace the old battery (B) with a fresh AA NiMH 1000 mAh rechargable battery.
3. Put solar head (A) back together and replace the screws that were removed in first step.
CHARGING THE BATTERY
- For optimum performance, it is best to install the solar light in full sunlight and let it charge for 6-7 hours.
- Allow the light to run at least 8-12 entire charging and discharging cycles to reach the maximum capacity of the battery.
WINTER TIPS
- Keep debris and snow off the solar panel to allow the battery to recharge. If lights have been covered by snow for a long time, allow the battery to recharge in full, direct sunlight for at least 6-7 hours so it can maintain maximum capacity.
TROUBLESHOOTING
Problem | Solution |
---|---|
The nightly runtime for the lights is shorter. |
- The battery is not adequately charged. Locate the solar light in an area where it can receive the maximum amount of full, direct sunlight every day.
- The battery is reaching the end of its useful life. Replace the old battery with a new battery.
The lights do not turn on in the evening.|
- The solar panel is installed close to other light sources. Relocate the solar panel or eliminate the other light sources.
CARE & CLEANING
Clean the solar panel with a damp cloth. Do not use any chemicals or abrasives.
TECHNICAL SPECIFICATIONS:
Material: Iron & Plastic
Product Size : 123 x 123 x 1678 mm
Solar Panel : 0.4W/2V Poly crystalline
Battery : 1000mAh AA Ni-Mh battery
Light Source : 72 x SMD LED
Charging Hours: 6 – 8 hours
Working Time: 8 – 10 hours
© 2024 The Investment Company Europe B.V. HYUNDAI is a trademark of HYUNDAI Corporation holdings, Korea. Licensed to The Investment Company Europe B.V. All rights reserved.
Licensed by Hyundai Corporation Holdings, Korea. Imported/Distributed by The Investment Company Europe B.V. exclusively developed for sales in the Netherlands, Belgium, and Luxembourg.
PATENT PENDING
The artwork and design of this package are protected by European copyright law and may not be reproduced, distributed, displayed, published or used for any purpose without prior written permission. It is not permitted to alter, or reproduce any trademarks or copyright notice from this package.
NL / EN – www.alleenonline.nl
BE / FR – www.alleenonline.be
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>