BRESSER F004018 Photo tent with LED lighting Instruction Manual
- June 6, 2024
- BRESSER
Table of Contents
BR-PHT 160/200
Photo tent with LED lighting
INSTRUCTION MANUAL
Art. Nr. F004018 – F004019
GENERAL WARNINGS
DANGER OF BODILY INJURY! Do not use it in the presence of children or
animals. Store out of reach of children and animals.
RISK OF ELECTRIC SHOCK! This unit contains electronic parts that are
powered by a power source (AC adapter or batteries). Follow the instructions
carefully and do not attempt to power this device with anything other than the
power sources recommended in this instruction manual, otherwise, there is a
DANGER of an ELECTRIC SHOCK!
The glass body of a lamp can shatter when it reaches the end of its service
life. In this case, immediately disconnect the device from the power source
(pull out the mains plug). Even after disconnecting the mains plug, there is a
risk of electric shock due to residual charge!
Never bend, squeeze or pull power cables, connecting cables, extensions or
connectors. Protect cables from sharp edges and heat. Check this device,
cables, and connections for damage before use. Never attempt to operate a
damaged device or a device with damaged electrical parts! Damaged parts must
be replaced immediately by an authorized service agent.
Operate the device only in a completely dry environment and do not touch the
device with wet or damp body parts.
DANGER OF BLEND! Make sure that people and animals do not look into the
light. The high luminosity can blind the eyes and cause afterimages. This
impairment of vision can lead to accidents.
FIRE/EXPLOSION HAZARD! Always place the device in such a way that it
cannot tip over and ensure that it is stored in a reasonably safe place.
- Keep children and animals away from the device! You could knock the device over.
- Make sure that no one can trip over the connection cables of the device. The device could be knocked over.
- Do not expose the device to high temperatures. Use only the supplied AC adapter. Do not short-circuit the device or batteries or dispose of them in the fire! Excessive heat and improper handling can cause short circuits, fires, and even explosions!
IMPORTANT NOTE!
Do not disassemble the device! In the event of a defect, please contact your
dealer. They will contact the Service Center and can arrange the return of
this device for repair if necessary.
Disconnect the power supply by pulling the mains plug when the appliance is
not in use, in case of a longer interruption of operation, and before any
maintenance and cleaning work.
Place your device so that it can be disconnected from the power supply at any
time. The power outlet should always be near your appliance and should be
easily accessible, as the plug of the power cord serves as a disconnect device
from the main supply. To disconnect the unit from the mains, always pull the
mains plug and never pull the cable!
Do not subject the device to excessive vibrations.
SCOPE OF DELIVERY (FIG. 1)
- Long rods, 120cm (4x)
- Short rods, 100cm (12x)
- Large diffusion blanket (1x)
- Corner pieces (8x)
- Connecting pieces (4x)
- Background clips (3x)
- Power adapter (4x)
- LED lights w.Connection cable (4x)
- Diffusion blanket for lights (4x)
- Power cable w. switch (4x)
- Background paper (1x)
- Black cover (1x)
- Blue cover (1x)
GENERAL ASSEMBLY INSTRUCTIONS
Before assembly, remove all accessories from the package and lay them out on a
level surface.
Press the poles firmly into the corner pieces and connecting pieces during
assembly so that the cover later easier can be slipped over the frame!
MOUNTING (Fig. 2-11)
Step 1: Assemble the lower frame as shown. Assemble the vertical rods in the
corners of the lower frame.
Step 2: Assemble the upper frame as shown and place it on the vertical bars of
the lower frame.
Step 3: Open the straight zippers of the tent canvas so that it can be pulled
over the frame more easily.
Step 4: Close the straight zippers again. Raise the photo tent.
Step 5: Hook the background clips to the back top tent pole as shown.
Step 6: Attach the background paper to the background clips.
Step 7: Attach the magnetic LED lights to the tent poles in the corners at a
45-degree angle. Depending on the motif, the luminaires can be moved
individually.
TIP: 2 lamps per pole provide all-around lighting.
Step 8: (optional) Attach the diffusion cloths with hooks to the rods in front
of the LED lights.
TIP: The diffusion cloths create a softer, more even light.
Step 9: Lead the connection cables of the lights through the holes in the tent
canvas to the outside. Connect the connection cables to the mains adapters.
Connect the power cables to the power adapters.
Step 10: (optional) Attach the large diffusion cloth to the front (large opening) with Velcro.
COMMISSIONING
- Insert the Euro plug of the mains cable into the socket.
- Switch on the lights using the switch on the main cable.
WARRANTY www.bresser.de/warranty_terms
Errors and technical changes excepted.
Manual_F004018-F004019_BR-PHT_en_BRESSER_v122020a
Contact
Bresser GmbH Gutenbergstr. 2 46414
Rhede – Germany @BresserEurope
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>