CyberPower M140BUCR1 AC/DC Power Inverter Owner’s Manual

CyberPower M140BUCR1 AC/DC Power Inverter

Specifications

• Model: M140BUCR1
• Input Voltage: 13.8 Volts
• Output Peak Power: 140 Watts
• Output Continuous Power: 120 Watts
• AC Output: 120V/60Hz/Simulated Sine Wave
• USB-A Charging Output: 5V/2.4A Max
• USB-C Charging Output: 5V/15W Max
• Protection Features: Low Voltage, Overheat, Overload, Short Circuit

Product Usage Instructions

Important Safety Information
Before installing and using the CyberPower AC/DC Power Inverter, please read and follow these safety instructions:

1. Unplug the inverter from the DC power outlet.
2. Disassemble the DC plug as pictured.
3. Replace the 15 amp fuse.
4. Reassemble the DC plug as pictured.

Troubleshooting

into vehicle’s DC power
outlet.| Automotive electrical system requires ignition to be on.
No AC output power Over-heating.| Allow inverter to cool. Ensure that there is adequate
ventilation around the unit and load does not exceed the unit’s
Continuous Power rating (see specifications).| Vehicle’s battery voltage is below 11 volts. Unplug the
inverter and start the vehicle to charge the battery.

For More Information

Technical Support:

• Visit: CyberPowerSystems.com/support
• Toll-Free: 1-877-297-6937

Conformance Approvals
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment, installed and used in accordance with the instructions, may cause harmful interference to radio communications.

WARNING :
This product can expose you to chemicals including bisphenol A (BPA) and styrene (ABS), which is known to the State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov.

Contact Information:
Cyber Power Systems (USA), Inc. 4241 12th Avenue East, Suite 400 Shakopee, MN 55379 CyberPowerSystems.com

Features

• Power Plug
• AC Outlet (1)
• USB-A Charging Port (1)
• USB-C Charging Port (1)
• Cooling Fan Vents

Frequently Asked Questions (FAQ)

• Q: What should I do if my inverter is not providing AC output power?
  A: Allow the inverter to cool down and ensure proper ventilation. Check the vehicle’s battery voltage and start the vehicle if it’s below 11 volts.

• Q: How do I replace the fuse in the inverter?
  A: Unplug the inverter from the DC power outlet, disassemble the DC plug, replace the 15 amp fuse, and reassemble the DC plug as instructed in the manual.

• Q: Can I use both USB ports simultaneously?
  A: Yes, you can use both USB-A and USB-C ports simultaneously to charge multiple devices.

• Q: What are the protection features of this inverter?
  A: The inverter includes protection against low voltage, overheat, overload, and short circuit situations.

• Q: Is it safe to leave the inverter plugged into the vehicle’s DC power outlet when not in use?
  A: It is recommended to unplug the inverter when not in use to prevent draining the vehicle’s battery.

YOUR ULTIMATE ALLY IN POWER

AC/DC POWER INVERTER
(1 AC OUTLET & 2 USB PORTS)
M140BUCR1

FEATURES

1. Power Plug
2. AC Outlet (1)
3. USB-A Charging Port (1)
4. USB-C Charging Port (1)
5. Cooling Fan Vents

SPECIFICATIONS

• Model: M140BUCR1
• Input Voltage: 13.8 Volts
• Output Peak Power: 140 Watts
• Output Continuous Power : 120 Watts
• AC Output: 120 V/60 Hz/Simulated Sine Wave
• USB-A Charging Output : 5 V/2.4 A Max
• USB-C Charging Output: 5 V/15 W Max
• Protection Features: Low Voltage, Overheat, Overload, Short Circuit

WARNING: This product can expose you to chemicals including bisphenol A (BPA) and styrene (ABS), which is known to the State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov.

IMPORTANT SAFETY INFORMATION

BEFORE INSTALLING AND USING THE CYBERPOWER AC/DC POWER INVERTER, PLEASE READ AND FOLLOW THESE SAFETY INSTRUCTIONS:

• DO NOT operate the M140BUCR1 near flammable materials, flumes or gases.
• Always use the inverter where there is adequate ventilation.
• DO NOT obstruct the ventilation slots.
• Never immerse the unit in water.
• Proper cooling is essential when operating the inverter. Refrain from placing the inverter near the vehicle’s heat vent or in direct sunlight.
• Always turn the inverter off when not in use by removing it from the DC accessory port.
• Check the warning labels on battery chargers or adapters before connecting them to the inverter. DO NOT connect battery chargers or adapters that have warnings about using with inverters.

FUSE REPLACEMENT

1. Unplug the inverter from the DC power outlet.
2. Disassemble the DC plug as pictured.
3. Replace the 15 amp fuse.
4. Reassemble the DC plug as pictured.

TROUBLESHOOTING

inverter is securely plugged into vehicle’s DC power outlet.
Automotive electrical system requires ignition to be on.| Turn the vehicle ignition to the “Accessory” position.
Car’s DC power outlet fuse is blown.| Check the vehicle fuse panel and replace the damaged fuse.
Over-heating.| Allow inverter to cool. Ensure that there is adequate ventilation around the unit and load does not exceed the unit’s Continuous Power rating (see specifications).
Vehicle’s battery voltage is below 11 volts.| Unplug the inverter and start the vehicle to charge the battery.
Vehicle’s battery input voltage is higher than 15 volts.| Check your vehicle’s user guide for troubleshooting.
Inverter is overloaded.| Ensure load does not exceed the unit’s Continuous Power rating (see specifications).

FOR MORE INFORMATION

VisitCyberPowerSystems.com for more information regarding:

• Product information and certifications
• Product warranty
• Connected equipment guarantee

TECHNICAL SUPPORT

• Visit: CyberPowerSystems.com/support
• Toll-Free: 1-877-297-6937
  © 2024 Cyber Power Systems (USA), Inc. All rights reserved. All other trademarks are the property of their respective owners.

CONFORMANCE APPROVALS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

References

• CyberPower UPS Systems, Battery Backup, PDUs, USB Surge Protectors
• Support | CyberPower

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>