DEFINITIVE TECHNOLOGY DC-80 MAX SUR Series Premium In Ceiling Surround

Speaker

Product Information

Specifications:

• Models: DC-65 PROTM, DC-65 PRO SITM, DC-80 PROTM, DC-65 MAXTM, DC-80 MAXTM, DC-80 MAX SURTM
• Speaker Sizes: DC-65 PRO / PRO SI – 109mm (4.3 in.), DC-65 MAX – 132mm (5.2 in.), DC-80 PRO – 128mm (5.01 in.), DC-80 MAX / MAX SUR – 137mm (5.4 in.)

Product Usage Instructions

1. Unpack
   Check the box contents: Grille, Speaker with frame, Cutout template, and Literature pack.

2. Mark Speaker’s Location
   Select a location for the speaker with sufficient clearance above the ceiling. Tape the cutout template to the ceiling and trace a line around it.

3. Cut Ceiling Opening
   Remove the cutout template and cut along the marked line to create the opening. Be careful not to cut too large of an opening.

4. Detach Speaker Frame
   Use a screwdriver to turn each spring-loaded screw a half turn until they pop up. Remove the speaker assembly from the frame. Turn the screws back to the original position before installing the frame.

5. Install Speaker Frame
   Ensure mounting clamps are retracted. Insert the frame into the opening until the flange contacts the ceiling. Rotate the mounting clamps outwards and pull them against the ceiling to securely clamp the frame.

6. Connect Speaker Cable
   Secure the speaker cable to the frame with a cable tie. Pull out a maximum of 1 meter of speaker cable. Insert the speaker wires matching amp polarity.

7. Install Speaker Assembly
   Align the locking tabs with the frame holes and insert the speaker assembly into the frame. Push each fastener head until it clicks and locks.

8. Aim Speaker
   Aim the speaker toward the primary listening position without pushing on the speaker cone to avoid damage.

9. Aim Tweeter
   Aim the pivoting tweeter toward the primary listening position without pushing on the tweeter diaphragm to avoid damage.

10. Set High Frequencies
    2dB for DC-65 MAX, DC-80 MAX, DC-80 MAX SUR models.

FAQ:

Q: Can I install these speakers in a bathroom or outdoor area?
A: These speakers are designed for indoor use only and should not be installed in areas exposed to moisture or extreme weather conditions.

Unpack

Check the box contents: (a) Grille, (b) Speaker with the frame, (c) Cutout template, and (d) Literature pack.

Mark Speaker Location

1. Select a location for the speaker that has sufficient clearance above the ceiling to avoid any interference with electrical wiring, plumbing, or other fixtures.
2. Tape the supplied cutout template to the ceiling and trace a line around the template onto the ceiling.

Cut Ceiling Opening

Remove the cutout template and cut along the marked line to create the opening. Be careful not to cut too large an opening.

Detach Speaker Frame

1. Use a screwdriver to turn each of the spring-loaded screws a half turn until they pop up.
2. Remove the speaker assembly from the frame.
3. Turn the screws back to the original position (so the surface of the screw head matches the contour of the speaker) before installing the frame in the ceiling.

Install Speaker Frame

1. Ensure the mounting clamps are in the retracted position.
2. Insert the frame into the opening until the flange contacts the ceiling.
3. While holding the frame in place, rotate the mounting clamps outwards, then pull them against the ceiling to securely clamp the frame.

Optional:
Secure the frame to a ceiling joist using a safety wire through one of the frame holes.

Connect Speaker Cable

1. Secure the speaker cable to the frame with a cable tie through the frame holes.
2. If the speaker cable is connected to an amplifier, turn off the amplifier.
3. Pull a maximum of 1 meter (3.28 ft.) of speaker cable out through the opening.
4. Push down the spring terminals; insert the speaker wires, matching amp polarity.

Note:
The DC-65 PRO SI model has two sets of terminals for stereo operation.

Install Speaker Assembly

1. Align the locking tabs with the holes in the frame, then insert the speaker assembly into the frame.
2. Push each fastener head in with your finger or a screwdriver until it clicks and locks.

Aim Speaker

DC-65 MAX / DC-80 MAX / DC-80 MAX SUR

Aim the speaker toward the primary listening position.

CAUTION:
Do not push on the speaker cone as this can damage it. Always push on the outer part of the speaker housing only.

Aim Tweeter

DC-65 PRO/DC-65 PRO SI/DC-80 PRO/DC-65 MAX/DC-80 MAX.

Aim the pivoting tweeter toward the primary listening position.

CAUTION:
Do not push on the tweeter diaphragm as this can damage it. Always push on the outer part of the tweeter housing only. Note: DC-65 PRO SI has dual tweeters mounted to one pod that pivot together.

Set High Frequencies

DC-65 MAX / DC-80 MAX / DC-80 MAX SUR

Set the High-Frequency (HF) selector for the desired high-frequency balance. The options are: -2dB high-shelf cut, 0dB (neutral), or +2dB high-shelf boost.

Paint Grille

Paint Grille (Optional)

If required, paint the grille before installing it. After painting the grille, make sure that the grille holes are not clogged.

Attach Grille

Attach the grille to the speaker. The grille is held in place magnetically and will attach securely to the speaker when held near the speaker.

Setup Is Complete

support.definitivetechnology.com

The speaker is now installed and ready for use. Scan the QR code or visit the URL for product support.

WHAT OBSESSION SOUNDS LIKE®
Share Photos

• Dymension

Sound United, LLC
dba Masimo Consumer 5541 Fermi Court Carlsbad, CA 92008 U.S.A.

• EU Contact:
  Sound United Europe, A division of D&M Europe B.V. Beemdstraat 11, 5653 MA Eindhoven, The Netherlands.

• UK Importer:
  D&M Audiovisual Ltd. Dale Road, Worthing, West Sussex BN11 2BH United Kingdom.

References

• Support Home Page

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>