DiXSG UCon 4G Solar Trail Camera User Guide
- June 12, 2024
- DiXSG
Table of Contents
**4G Solar Trail Camera
**
Ucon
User Guide
V1.0
Product Diagram
Product Instruction
- Signal strength indicator green-strong blue-medium red-weak
- Reset button: press and hold for 3S to enter reset pairing state (blue light flashing + prompt tone)
- Status indicator lights up red when powered on, the blue light is always on, you can scan the code to add the device
- Charging indicator the green light is always on during charging, and the light is off when fully charged
Application Description
APP INSTALLATION
- Scan the following QR codes or seach for ‘Mon” from the AppStore(for iOS devices) or Google Play Store (for Android smartphones) to download and install the app. http://app.ubianet.com/app/ucon
APP REGISTRATION
- Open the app then input your E-mail address then press ‘Register’. Check and select to agree the agreement then your E-mail box will get an verification code. ( For better user’s experience, please allow to open all permissions to avoid missing any notifications from the app.)
- Set the login password and confrim the login password. Then press ‘Register’ to next step. (For your password safety, the password requires more than 8 characters plus combination of letters)
- We send a verify mail to you, go to your mail box click the link to complete the verification.
- Enter your E-mail address, and password , click login . (APP will auto fill the account infomaion)
CONNECTION
- Press ‘Add Location’ then set the room or position as per reminders.
- Enter your family name and then press ‘Next’.
- Input the necessary information just like Country, Province, then press ‘Done’.
- Press ‘Add a device’ to add a smart device
- insert the SIM card into device then put the battery into the decice , and some of models need install antenna.
- After the power on the device, wait for about 1 minute the device bule LED light up , Then press next.
- If the device blue LED not light up, please check below config notes.
- Find the UID QR code on camera , then use APP scan the OR code.
- APP are search the device in intemet it may take 5-60 seconds.
- Select the name and device location then press ‘Done.’
- The device will enter to the device list automatically. Setup success! The device is ready to use.
- Notes about PIR detection The user can adjust the sensing distance by changing the FIR detection sensitivity..
•Lon: The detection distance can reach up to 9 meters. ‘Medium: The detection distance can reach up to 14 meters. ‘High: The detection distance can reach up to 20 meters.
USING THE APP
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, theuser is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving an tenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement: This equipment complies with FCC
radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.