BEA LZR-I30 Remote Control Instruction Manual

LZR-I30 Remote Control

“`html

Specifications

• Product Models: LZR-I30, LZR-S600, FALCON, FALCON EX, PHOENIX
  EX, IS40, IS40XL, IS40P, EAGLE ARTEK, EAGLE HIGH-MOUNT,
  BODYGUARD-T, LZR-FLATSCAN SW, LZR-FLATSCAN 3D SW, ULTIMO, IXIO-DT1,
  IXIO-DT1 IND, IXIO-DT1 V, IXIO-ST, IXIO-ST IND

Product Usage Instructions

General Remote Use

After unlocking, the red LED flashes and the sensor can be
adjusted by remote control. If the red LED flashes quickly after
unlocking, an access code from 1 to 4 digits is required.

Adjusting Parameters

1. To end an adjustment session, always lock the sensor.
2. Press UNLOCK.
3. Choose the parameter to adjust.

Checking a Value

1. Choose the value to check.
2. Press LOCK twice.
3. Press UNLOCK.
4. Choose the parameter to confirm.

Restoring to Factory Values

1. Press “?” (X = number of flashes = value of the
   parameter).

2. Press LOCK twice.

3. Press UNLOCK.

4. Press MAGIC WAND.

Saving and Changing Access Code

1. To save an access code, press 9 followed by * when no green LED
   is available (the signal will be red).

2. Press LOCK twice.

3. To change an access code, press UNLOCK and enter the existing
   code, then press LOCK and enter a new 4-digit code.

Deleting an Access Code

1. Press UNLOCK and enter the existing code.
2. Press LOCK and enter 0 followed by LOCK to delete the
   code.

If You Forget the Access Code

If you forget the access code, you can cut and restore power to
the sensor for 1 minute to access it without the code. LED flashes
quickly (1x), LED flashes slowly, LED flashes once (1x), or LED is
off indicate different states during this process.

FAQ

Q: How do I adjust the sensor using the remote control?

A: After unlocking, you can adjust the sensor parameters using
the remote control. Follow the steps outlined in the user manual
based on your specific requirements.

Q: How do I save or change the access code?

A: To save an access code, press 9 followed by *. When changing
the access code, enter the existing code and then input a new
4-digit code as instructed in the manual.

Q: What should I do if I forget the access code?

A: If you forget the access code, you can reset it by cutting
and restoring power to the sensor for 1 minute. During this time,
you can access the sensor without needing the access code.

“`

ENGLISH

Visit website for available languages of this document.
KEYS

REMOTE CONTROL
How to use the remote control

GENERAL KEYS
Unlock Lock Check value Incremental increase Incremental decrease Setup / Teach-in Factory values Presettings

FUNCTION KEYS
See pages 3 ­ 12 for button assignments per product.

COLOR KEYS

LZR-FLATSCAN /
Safety Motion
/

LZR-WIDESCAN Virtual Pull Cord
Safety Reopening Presence

PRODUCTS
LZR-I30 / LZR-S600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FALCON / FALCON EX / PHOENIX EX . . . . . . . . . . . . . 4 IS40 / IS40XL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 IS40P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 EAGLE ARTEK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 EAGLE HIGH-MOUNT . . . . . . . . . . . . . . . . . . . . . . . . 8

BODYGUARD-T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 LZR- FLATSCAN SW. . . . . . . . . . . . . . . . . . . . . . . . . . 10 LZR-FLATSCAN 3D SW . . . . . . . . . . . . . . . . . . . . . . . 11 ULTIMO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 IXIO-DT1 / IXIO-DT1 IND / IXIO-DT1 V . . . . . . . . . . 13 IXIO-ST / IXIO-ST IND . . . . . . . . . . . . . . . . . . . . . . . . 14

©BEA | Original Instructions 75.0043.04 REMOTE CONTROL 20240821

Page 1 of 14

GENERAL REMOTE USE

After unlocking, the red LED flashes and the sensor can be adjusted by remote control.

If the red LED flashes quickly after unlocking, you need to enter an access code from 1 to 4 digits.

ADJUSTING ONE OR MORE PARAMETERS

To end an adjustment session, always lock the sensor.

press UNLOCK

choose parameter

CHECKING A VALUE

choose value

press LOCK twice

press UNLOCK

choose parameter

RESTORING TO FACTORY VALUES

press ?

x
X = number of flashes = value of the parameter

press LOCK twice

press UNLOCK

press MAGIC WAND

SAVING AN ACCESS CODE

press 9

press LOCK twice

• When no green LED is available, the signal is red.

press UNLOCK

press LOCK

enter 4 digits

The access code (1 ­ 4 digits) is recommended to set sensors that are installed close to each other.

CHANGING AN ACCESS CODE

press UNLOCK

enter the existing code

press LOCK

enter 4 digits

DELETING AN ACCESS CODE

press UNLOCK

enter the existing code

press LOCK

press 0 press LOCK

If you forget the access code, proceed as follows:

press UNLOCK

Cut and restore power to the sensor

1 Min. During 1 minute, you can access the sensor without access code

LED flashes quickly LED flashes LED flashes slowly

LED flashes once 1x
LED is off

Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462 | General Tech Questions: techservices-us@BEAsensors.com | www.BEAsensors.com
©BEA | Original Instructions 75.0043.04 REMOTE CONTROL 20240821

Page 2 of 14

APPENDIX: LZR-I30 / LZR-S600 FUNCTIONS

BUTTON

FUNCTION

MOUNTING SIDE OPTIONAL FIELD WIDTH OPTIONAL FIELD HEIGHT
SAFETY FIELD WIDTH SAFETY FIELD HEIGHT ACTIVE DETECTION
CURTAINS UNCOVERED ZONE IMMUNITY FILTER

deactivate curtain on both fields
2 in (S600 default)

LEFT (background)
activate curtain only on optional field
4 in (I30 default) environment:
indoor

RIGHT

LEFT

RIGHT

CENTER

(background) (no background) (no background) (no background)

I30: no field = 000 / minimum = 020 / maximum = 360 / default = 200 S600: no field = 000 / minimum = 020 / maximum = 984 / default = 400

I30: no field = 000 / minimum = 020 / maximum = 360 / default = 200 S600: no field = 000 / minimum = 020 / maximum = 984 / default = 400

I30: no field = 000 / minimum = 020 / maximum = 360 / default = 200 S600: no field = 000 / minimum = 020 / maximum = 984 / default = 400

I30: no field = 000 / minimum = 020 / maximum = 360 / default = 200 S600: minimum = 004 / maximum = 984 / default = 400

activate curtain only on safety field

6 in

8 in

10 in

environment: environment: environment: outdoor low outdoor med. outdoor high

objects: indoor

objects:

objects:

outdoor low outdoor med.

objects: outdoor high

MIN. OBJECT SIZE

off

2 in

4 in

6 in

8 in

OUTPUT ACTIVATION DELAY
DETECTION FIELD REDIRECTION
OUTPUT CONFIGURATION

off
R1: optional R2: safety

100 ms
R1: optional or safety R2: safety
R1: A – NO R2: P – NC

200 ms
R1: P – NC R2: A – NO

300 ms
R1: P – NC R2: P – NC

400 ms
R1: A – NO R2: A – NO

500 ms

600 ms

700 ms

800 ms

activate curtains on both fields
900 ms

Click here for LZR-I30 User’s Guide. Click here for LZR-S600 User’s Guide.

©BEA | Original Instructions 75.0043.04 REMOTE CONTROL 20240821

Page 3 of 14

APPENDIX: FALCON, FALCON EX, PHOENIX EX FUNCTIONS

BUTTON

FUNCTION

FIELD SIZE

XXS

XS

S

L

XL

XXL

HOLD-OPEN TIME

0.5 s

1 s

2 s

3 s

4 s

5 s

6 s

7 s

8 s

9 s

OUTPUT CONFIGURATION

active

passive

DETECTION MODE

BI

UNI

UNI AWAY

DETECTION FILTER

1

2

3

4

5

6

Click here for FALCON Family User’s Guide. Click here for FALCON EX Family User’s Guide. Click here for PHOENIX EX Family User’s Guide.

©BEA | Original Instructions 75.0043.04 REMOTE CONTROL 20240821

Page 4 of 14

APPENDIX: IS40 / IS40XL FUNCTIONS

BUTTON

FUNCTION

FIELD SIZE (SENSITIVITY)

XXS

XS

S

HOLD-OPEN TIME

0.5 s

1 s

2 s

3 s

4 s

5 s

6 s

DETECTION MODE
DETECTION FILTER
OUTPUT CONFIGURATION
FREQUENCY MAX. PRESENCE DETECTION TIME AIR CURTAIN IMMUNITY

Presence +
Activation: standard
mode
30 s

BI

UNI

UNI AWAY

All targets in motion
Presence +
Activation: pulse on entry

All targets in motion + interference immunity
Presence +
Activation: pulse on exit

Low `Pedestrian/ Parallel traffic’ Rejection + Interference Immunity
Presence +
Activation: pulse on entry first / last line

Medium `Pedestrian/ Parallel traffic’ Rejection + Interference Immunity
Presence +
Activation: pulse on exit first / last line

High `Pedestrian/ Parallel traffic’ Rejection + Interference Immunity
Presence +
Activation: remains active (when motion
is detected) until presence
zone in cleared

Extra High `Pedestrian/ Parallel traffic’ Rejection + Interference Immunity
Presence +
Activation: remains active (when motion
and AIR are detected) until presence zone
in cleared

A

B

1 min

2 min

5 min

10 min

20 min

1 hr

low

normal

high

L 7 s
1.5 hr

TARGET SIZE

XL

XXL

8 s

9 s

2 hr

no learn

AIR PATTERN SIZE

Click here for IS40 / IS40XL User’s Guide.

©BEA | Original Instructions 75.0043.04 REMOTE CONTROL 20240821

Page 5 of 14

APPENDIX: IS40P FUNCTIONS

BUTTON

FUNCTION

RELAY CONFIGURATION

OUTPUT REDIRECTION

ACT: presence PRES: presence

FREQUENCY

MAX. PRESENCE DETECTION TIME

3 s

AIR CURTAIN IMMUNITY

Mot: active Pres: passive ACT: AIR entry
pulse PRES: presence
A
1 min
low

Mot: passive Pres: active ACT: AIR exit pulse PRES: presence
B
2 min
normal

Mot: passive Pres: passive

Mot: active Pres: active

ACT: first/last line AIR entry pulse
PRES: presence

ACT: first/last line AIR exit pulse
PRES: presence

5 min high

10 min

ACT: presence PRES: presence
20 min

ACT: presence PRES: presence
1 hr

TARGET SIZE

1.5 hr

AIR PATTERN SIZE

2 hr

no learn

Click here for IS40P User’s Guide.

©BEA | Original Instructions 75.0043.04 REMOTE CONTROL 20240821

Page 6 of 14

APPENDIX: EAGLE ARTEK FUNCTIONS

BUTTON

FUNCTION

FIELD SIZE
RAD: SHAPE
MOUNTING HEIGHT IMMUNITY FILTER
DETECTION MODE 1 OUTPUT
CONFIGURATION HOLD-OPEN TIME DOOR CONTROL 2

XXS

XS

S

L

XL

= wide (default) = narrow

To query the specific width, press

.

The sensor will blink the number of times that it is set to, and then the green LED will blink either 1 time (narrow shape) or 2 times (wide shape).

Example: If FIELD SIZE = large and FIELD SHAPE = narrow, the LED with blink 7 times, and then 1 time.

<10 ft

10 ft

low

normal

high

BI

UNI

UNI MTF

UNI AWAY MTF & AWAY

N.O.

N.C.

0.5 s

1 s

2 s

3 s

4 s

5 s

6 s

7 s

8 s

auto

open

closed

FACTORY RESET

full

XXL
highest 9 s
partial 3

1 bi = two-way detection uni = one-way detection towards sensor uni MTF = one- way detection with motion-tracking feature uni AWAY = one-way detection away from sensor
2 open = sensor detects constantly, LED on. closed = sensor is in standby and does not detect, LED off
3 outputs are not reset

Click here for EAGLE ARTEK User’s Guide.

©BEA | Original Instructions 75.0043.04 REMOTE CONTROL 20240821

Page 7 of 14

APPENDIX: EAGLE HIGH-MOUNT FUNCTIONS

BUTTON

FUNCTION

ZONE SIZE

XXS

IMMUNITY FILTER

DETECTION MODE 1

OUTPUT CONFIGURATION 2

HOLD-OPEN TIME

0.5 s

MOUNTING HEIGHT

DOOR CONTROL 3

XS low BI A 1 s < 10 ft auto

1 bi = two-way detection uni = one-way detection towards sensor uni PRM = one- way detection also of people with reduced mobility uni AWAY = one-way detection away from sensor
2 A = active output (N.O. contact); relay energizes upon detection P = passive output (N.C. contact); relay de-energizes upon detection
3 open = sensor detects constantly, LED on. closed = sensor is in standby and does not detect, LED off

S

L

XL

XXL

normal

high

L

XL

highest

UNI

UNI MTF

UNI AWAY MTF & AWAY

P

2 s

3 s

4 s

5 s

6 s

7 s

8 s

9 s

10 ft

open

closed

Click here for EAGLE HIGH-MOUNT User’s Guide.

©BEA | Original Instructions 75.0043.04 REMOTE CONTROL 20240821

Page 8 of 14

APPENDIX: BODYGUARD-T FUNCTIONS

BUTTON

FUNCTION

INTERFACE

DOOR CONTROL

MODES OF OPERATION
INFRARED FREQUENCY
SENSITIVITY
HOLD TIME OUTPUT
CONFIGURATION AUTO-LEARN TIME
PATTERN WIDTH

PATTERN DEPTH

IMMUNITY

• default 6 = door closed, default 7 = door open

normal min 0.5 s
30 s

new style normal

old style (LO21)
door permanently
open

door permanently
closed

MP mode Record mode

Mode: normal Mode: normal Mode: quiet

Freq: low

Freq: high

Freq: low

Mode: quiet Freq: high

9 s

N.O.

N.C.

1 m

2 m

3 m

5 m

7 m

10 m

wide (closed door)
deep (threshold on)
low (normal)

middle (open door)
medium (threshold on,
open)
medium (rain)

asymm. left narrow
limited (threshold on)
high (snow)

asymm. right narrow
deep (threshold off)

narrow left
medium (threshold off,
closed)

narrow right
limited (threshold off)

15 m
asymm. left wide

10 s

infinite

asymm. right wide

center narrow

Click here for IS40 / IS40XL User’s Guide.

©BEA | Original Instructions 75.0043.04 REMOTE CONTROL 20240821

Page 9 of 14

APPENDIX: LZR-FLATSCAN SW FUNCTIONS

BUTTON

FUNCTION
PINCH ZONE WIDTH
PINCH ZONE HEIGHT
DOOR LEAF WIDTH
DOOR LEAF HEIGHT OUTPUT
CONFIGURATION IMMUNITY FILTER
UNCOVERED ZONE ANTIMASKING & BACKGROUND

OFF / OFF

R1: NO R2: NC
low
3/4 in
OFF / ON

no field = 000 / minimum = 001 / maximum = 040 / default = 015

no field = 000 / minimum = 001 / maximum = 157 / default = 157

no field = 000 / minimum = 001 / maximum = 157 / default = 157

no field = 000 / minimum = 001 / maximum = 157 / default = 157

R1: NC R2: NO

R1: NC R2: NC

R1: NO R2: NO

high

1 1/2 in

2 1/4 in

3 in

4 in

4 3/4 in

5 1/2 in

6 1/4 in

7 in

ON / OFF

ON / ON

Click here for LZR-FLATSCAN SW User’s Guide.

©BEA | Original Instructions 75.0043.04 REMOTE CONTROL 20240821

Page 10 of 14

APPENDIX: LZR-FLATSCAN 3D SW FUNCTIONS

BUTTON

FUNCTION
PINCH ZONE WIDTH
DOOR LEAF WIDTH
DOOR LEAF HEIGHT OUTPUT
CONFIGURATION 1 UNCOVERED ZONE
ANTIMASKING / BACKGROUND

OFF / OFF

N.O. 3/4 in OFF / ON

no field = 000 / minimum = 001 / maximum = 040 / default = 015

no field = 000 / minimum = 001 / maximum = 157 / default = 157

no field = 000 / minimum = 001 / maximum = 157 / default = 157

N.C.

1 1/2 in

2 3/8 in

3 1/4 in

4 in

4 3/4 in

ON / OFF

ON / ON

5 1/2 in

DETECTION FIELD DEPTH
1 Always enter 3 digits for output parameters: · 1st digit refers to Output 1 (O1) = STOP · 2nd digit refers to Output 2 (O2) = REOPEN · 3rd digit refers to Output 3 (O3) = VIRTUAL PUSH BUTTON

1 curtain

2 curtains

3 curtains

4 curtains

Click here for LZR-FLATSCAN 3D SW User’s Guide.

©BEA | Original Instructions 75.0043.04 REMOTE CONTROL 20240821

Page 11 of 14

APPENDIX: ULTIMO FUNCTIONS

BUTTON

FUNCTION
IR:Width IR:Curtains IR:Immunity IR:PresTime
IR:Freq Rad:Fieldsize
Rad:Shape
Rad:Direction Rad:Immunity Out1Funct 3
Out1Logic Out1HoldTime
InTestMode FactoryRst

wide

standard

narrow

left, angled right, angled

0

1

2

3

4

5

6

7

normal

outdoor

enhanced

30 sec

1 min

2 min

5 min

10 min

20 min

60 min

infinite

auto-synch

IXIO 1

freq A 2

freq B 2

small

large

LCD: “narrow” and “wide” setting options
Remote Control: After pressing the Rad:Fieldsize button, use the plus sign button to select the Wide shape or the minus sign button to select the Narrow shape. Numeric remote control buttons are only applicable to the Rad:Fieldsize function.

off

BI <>|

UNI >|

MTF <|

low

high

off

RAD or IR

RAD

N.O.

N.C.

0.5 sec

1 sec

2 sec

3 sec

4 sec

5 sec

6 sec

7 sec

8 sec

9 sec

off

on

auto

full

partial 4

1 > V5.0 auto-synch
2 for use with IXIO if synchronization issues occur
3 The sensor LED will briefly flash RED during monitoring communication with the door control. This indicates that external monitoring is functional. Monitoring functionality must be active on the sensor and door control, and monitoring wires must be properly connected to the door control.
4 Partial reset is only available via remote control. Partial restores all adjustable settings except Out1Logic and Out2Logic.

Click here for ULTIMO User’s Guide.

©BEA | Original Instructions 75.0043.04 REMOTE CONTROL 20240821

Page 12 of 14

APPENDIX: IXIO-DT1 / DT1 IND / DT1 V FUNCTIONS

BUTTON FUNCTION

RAD: FIELDSIZE RAD: SHAPE
RAD: IMMUNITY

small

LCD: “narrow” and “wide” setting options (default = wide)

Remote Control:

= wide,

= narrow

low

RAD: DIRECTION 1

off

BI

UNI

MTF

RAD: HOLDTIME

0.5 sec

1 sec

2 sec

3 sec

RAD: REENTRY RAD: OUTPUT 2 AIR: OUTPUT 2 AIR: IMMUNITY

small

DeEner/N.O. N.C.
DeEner/N.O. N.C.
normal

Ener/N.C. N.O.
Ener/N.C. N.O.
enhanced

Ener/N.C. N.C.
Ener/N.C. N.C.

AIR: NUMBER

1

2

AIR: PRESENCE TIME

30 sec

1 min

AIR: FREQ

A

B

TEST 3 REDIRECTION 4

off
R1 MW R2 IR

on
R1 MW or IR R2 IR

FACTORY RESET 5

4 sec >
DeEner/N.O. N.O.
DeEner/N.O. N.O.
2 min

1 MTF = motion tracking feature uni + reentry: BEA recommends only adjusting using the LCD
2 RADAR: DeEner = de-energized relay, Energ = energized relay; N.O. = normally open, N.C. = normally closed AIR: N.O. = normally open, N.C. = normally closed
3 The sensor LED will briefly flash RED during monitoring communication with door control. This indicates that external monitoring is functional. Monitoring functionality must be active on the sensor and door control, and monitoring wires must be properly connected to the door control.
4 REDIRECTION setting (F1 on remote control): R1-MW, R2-IR (F1=0): R1 = MW (i.e. motion detection) R2 = IR (i.e. presence detection) R1-MW or IR, R2-IR (F1=1): R1 = MW or IR (i.e. motion or presence detection) R2 = IR (i.e. presence detection)
5 partial: outputs are not reset
©BEA | Original Instructions 75.0043.04 REMOTE CONTROL 20240821

5 sec >
5 min

large

6 sec >

7 sec >

uni + reentry
8 sec >

high
9 sec large

mode B

10 min

20 min

60 min

infinite

full

partial

Click here for IXIO-DT1 User’s Guide. Click here for IXIO-DT1 INDUSTRIAL User’s Guide.
Click here for IXIO-DT1 V User’s Guide.

Page 13 of 14

APPENDIX: IXIO-ST / ST IND FUNCTIONS

BUTTON FUNCTION

AIR: OUTPUT 1

AIR: IMMUNITY

AIR: NUMBER

AIR: PRESENCE TIME

AIR: FREQ

TEST 2

off

FACTORY RESET 3

DeEner/N.O. N.C.
normal 1
A on

Ener/N.C. N.O.
enhanced
2
30 sec
B

Ener/N.C. N.C.

DeEner/N.O. N.O.

1 min

2 min

5 min

1 N.O. = normally open, N.C. = normally closed
2 The sensor LED will briefly flash RED during monitoring communication with door control. This indicates that external monitoring is functional. Monitoring functionality must be active on the sensor and door control, and monitoring wires must be properly connected to the door control.
3 partial: outputs are not reset

mode B

10 min

20 min

60 min

infinite

full

partial

Click here for IXIO-ST User’s Guide. Click here for IXIO-ST INDUSTRIAL User’s Guide.

©BEA | Original Instructions 75.0043.04 REMOTE CONTROL 20240821

Page 14 of 14

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>