2AX76-KINY Wireless Kinetic Switch

Wireless Kinetic Switch

Specifications:

• Switch type: Push-button
• Power mode: Self-powered with MEA module
• Modulation mode: RF
• Work frequency: [Frequency]
• Button: Function button
• Work range: [Range]
• Lifetime: [Estimated lifetime]
• Dimensions: [Dimensions]
• Work temperature: [Temperature range]

Product Information:

The Wireless Kinetic Switch is a self-powered push-button switch
equipped with a Micro Energy Acquisition (MEA) module. This module
converts mechanical energy into electricity to power the RF
chipset, enabling the switch to wirelessly control devices paired
with the Ebelong Wireless receiving controller.

Usage Instructions:

1. Ensure the Wireless Kinetic Switch is within the working range
   of the Wireless Receiving Controller.

2. To pair the switch with the controller, press and hold the
   function button on the controller for 3 seconds until the indicator
   light starts flashing.

3. Release the button to enter pairing mode. Press the Wireless
   Kinetic Switch, and the controller’s indicator light will turn off,
   indicating successful pairing.

4. The switch can now be used to power on/off devices connected to
   the Wireless Receiving Controller.

FAQ:

Q: What should I do if the switch is not pairing with the

controller?

A: Make sure the switch is within range of the controller and
follow the pairing instructions carefully. If issues persist,
consult the dealer or refer to an experienced technician for
assistance.

Q: Can the Wireless Kinetic Switch be used outdoors?

A: The switch is designed for indoor use. Avoid exposing it to
extreme temperatures or moisture to ensure optimal performance.

Q: How long does the self-powered feature of the switch

last?

A: The estimated lifetime of the self-powered feature depends on
usage and environmental factors. It is designed to provide
long-lasting functionality.

Wireless Kinetic Switch Instruction
DESCRIPTION:
The Wireless Kinetic Switch is a push-button self-powered switch with MEA (Micro Energy Acquisition) module inside to transform mechanical energy into electricity to drive RF chipset work. It is able to power on/off after the pairing with Ebelong Wireless receiving controller

OPERATION:
The Wireless Kinetic Switch shall work with Wireless Receiving Controller.
Press and hold the function button of controller for 3 seconds and the indicator light will start to flash. Then release the button to enter pairing mode. Press the switch and the indicator light of controller will go out, which means the paring is successful.

SPECIFICATIONS
Item
Switch type Power mode Modulation mode Work frequency Button Work range Lifetime Dimensions Tray Work temperature

Spec
Push button Self-powered FSK 433 MHz 2 gang 80m Outdoor, 30m Indoor >100,000 times L33W16H65mm L56W4H107mm -20~ +55°C

FCC Warning
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected. –Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IC warning
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device
L’émetteur/récepteur exempt de licencecontenudans le présentappareilestconforme aux CNR d’Innovation, Sciences et Développementéconomique Canada applicables aux appareils radio exempts de licence. L’exploitationestautorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage; 2. L’appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d’encompromettre le fonctionnement.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>