DOMUS LINE LED Power X-Driver TW Instruction Manual

: June 6, 2024
: DOMUS LINE

Table of Contents

DOMUS LINE LED Power X-Driver TW
Specifications
OVERVIEW
INTRODUCTION
WARRANTY:
FCC warning:
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DOMUS LINE LED Power X-Driver TW

DOMUS LINE LED Power X-Driver TW PRO

Device in insulation class II. Connection to the earthing circuit is not necessary. Lamp power supply unit thermally protected at 110°C Independent transformer specially designed to be installed ”visible” (it can be used without the supplementary protective case and without being integrated into lights).This symbol indicates that the transformer complies with the European EN 61347-1 standard. The SELV symbol (Safety Extra Low Voltage) identifies a transformer in which touching the secondary circuit outputs, even if no lamps are connected, does not constitute a hazard. The product must be disposed of separately from urban waste, delivering it to the collection centres established by the prevailing standard. Adequate sorted waste collection contributes to preventing negative effects on the environment and health and favours reuse and/or recycling materials. Incorrect disposal of the product implies the application of the administrative sanctions envisaged by the prevailing regulation.

Specifications

| X-DRIVER TW 15Watt| X-DRIVER TW 30Watt| X-DRIVER TW 60Watt
---|---|---|---
Input voltage| 100-120VAC,220-240Vac

(100-120VAC for North America only)

| 220-240Vac
Input frequency| 50/60Hz
Input current| 0,25A for 100-120Vac

0,12A for 220-240Vac

| 0,40A for 100-120Vac

0,20A for 220-240Vac

| 0,40A for 220-240Vac
Output voltage| 24Vdc| 24Vdc| 24Vdc
Rated output power| 0-15W| 0-30W| 0-60W
Dimming range| 2%-100%
Operation mode| PWM+PFM
Ambient temperature| -20…+40°C
IP protection| IP20

Optional Accessories Table

Picture

| | | |

NOT FOR X-DRIVER 15W

| ****

OR

RADIO RECEIVER FOR LIGHTING CONTROL

| ****

–

| Radio receiver for lighting control

Model : CM2-XDTW RECEIVER CONTROLLER IC: 26990-CM2

FCC ID: 2AX76-CM2

| Radio receiver for lighting control

Model : CM3-XDTW RECEIVER CONTROLLER IC: 26990-CM3

FCC ID: 2AX76-CM3

| Radio receiver for lighting control

Model : CM4-XDTW RECEIVER CONTROLLER IC: 26990-CM4

FCC ID: 2AX76-CM4

| ****

–

Functional Fittings

| ****

PIR XD

IR XD

| IR XD PIR XD

Call-ME V17 TW

RC3-TW

RC1-TW

| ****

IR XD

PIR XD

APP

| ****

APP

| ****

–

OVERVIEW

DOMUS LINE LED Power X-Driver TW 1 DOMUS LINE
LED Power X-Driver TW 2 DOMUS
LINE LED Power X-Driver TW 5

App. DOMUS 4U
Enter to the APP, press Info and read the instructions. DOMUS 4U can control max. 5 X-DRIVER

DOMUS LINE LED Power X-Driver TW 7

WARNING:
Safety is guaranteed is these instructions are followed and therefore they must be kept. Installation may require the involvement of qualified personnel. Before proceeding with installation of the device ensure that the environmental conditions are in compliance with and suitable for the product characteristics. Before any operation on the device disconnect mains power.

INTRODUCTION

Power supply is designed exclusively for LED lamps. It can be used together with control modules, IR / PIR sensors, remote control remote controls and APP (see optional table accessories). The built-in protection circuit turns off the power supply when there is a short circuit, overload or overheating. X-DRIVER TW restarts automatically after the problem has been resolved.

WARRANTY:

The warranty on the device is valid only if powered by a power supply provided by DOMUS Line. The warranty’s general terms and conditions for this device are available at www.domusline.com This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC warning:

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

IC warning
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.