DOMUS LINE CALL-ME Remote Radio Emitter for Lighting Control Instructions
- June 6, 2024
- DOMUS LINE
Table of Contents
DOMUS LINE CALL-ME Remote Radio Emitter for Lighting Control
The instrument is in protection class III. The power supply must be furnished by a security transformer.
To protect the environment, do not throw the instrument with the normal waste at the end of his life, but bring it to the specific points of collection for this waste foreseen by the norm.
The instrument is suitable only for inside use.
TECHNICAL DATA:
FOR RECEIVER CONTROLLER TW: Power supply: 24Vdc Max power: 60Watt
FOR CALL-ME V17 TW : Remote control range 15 meters. Battery type used: CR2032
(3V) lithium.
PROGRAMMING RECEIVER:
- Remove the insulating flap (1) from the transmitter.
- Connect the receiver as shown in fig.1,2.
- Connect the power plug to the power supply, the blue LED (2) flashes.
- Briefly press the button (2) of the receiver.
- The blue led (2) lights up for a time of 60 sec. within which you have to complete the programming operation, briefly press twice button (3) on the transmitter (1) . The blue led turns off (2) confirms the correct programming of the system
OPERATION ON-OFF-DIMMER:
The device can be switched on and off by simply pressing the button (3), while
a longer touch adjusts the intensity of the light up or down. A brief flash of
light indicates the achievement of maximum brightness. The brightness level
obtained will be stored until the next adjustment. The signaling LED (4)
confirms the sending of the signal to the receiver. To switch to ON-OFF-TW
press briefly 2 times (3)
OPERATION ON-OFF-TW:
Switching on and off is carried out simply by briefly touching button(3). By
long-pressing you can change the colour shade of the connected device (tunable
function). The selected colour will be stored until the next adjustment
(Colour Memory). To switch to
ON-OFF DIMMER function press briefly 2 times the key (3).
BATTERY REPLACEMENT (fig: 3,4,5,6):
- Remove the cap of the CALL-ME support (5) by levering with a screwdriver (fig. 3)
- Remove the transmitter (6) from the support (7) (fig.4).
- Replace the battery (8) with a model with similar characteristics, making sure to observe the correct polarity (fig. 5).
- Refit the components of the transmitter, making sure to match the reference marks printed on the shells (fig.6).
BATTERY POWERED DEVICES
These precautions apply to all products with disposable or rechargeable
batteries. Improper use of batteries may cause leakage, overheating, or
explosion of the battery. Battery fluid is corrosive, it can be toxic, it can
cause burns to the eyes and skin and it is harmful if swallowed.
To reduce the risk of injury:
- Keep batteries out of the reach of children
- Do not heat, open, or tamper with the batteries; do not dispose of in fire.
- Avoid contact between metal objects and the battery terminals of the device, as they may overheat and cause burns.
- Remove batteries if they are exhausted, or before storing the device for a long period of time. Always remove the old batteries with low charge or discharged and recycle or dispose of them in accordance with applicable law.
- In case of leakage, remove the battery carefully, avoiding the liquid to come in contact with skin or clothing. If the battery fluid comes into contact with skin or clothing, immediately rinse the exposed parts with water. Before inserting new batteries, wipe the housing with a damp paper towel.
Only for disposable batteries (non-rechargeable):
Use only batteries of the appropriate size and type.
Choking hazard:
This device contains small parts that could pose a choking hazard to small
children. Keep these small parts out of the reach of children.
WARNING: Make sure that the environmental conditions in which the
equipment is installed are suitable.
The installation may require the involvement of qualified personnel.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC warning
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IC warning
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device. The
device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Domus Line s.r.l., Via Maestri del Lavoro 1, 33080 Porcia (PN) Italy – tel. +39 0434 /595911 – fax. +39 0434/923345 – info@domusline.com – www.domusline.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>