PACIFIC X10DR-PU2 Secure Wireless Microphone Instruction Manual

PACIFIC X10DR-PU2 Secure Wireless Microphone

How to install Programmer:

Runs On PC or Mac running Windows 7/11
NOTE : Requires USB 2 Port. The programmer will not work with USB 3 – if your PC only has USB3 ports, we suggest you attach the X10DR device via a usb patch block as most are USB 2.) Included with the Programmer download file application are instructions on how to set-up the programmer on your Windows 7/11 PC. Please follow those instructions to install the programmer correctly onto your computer.

How to use Programmer:

Runs On PC running Windows 7/10 Requires a USB 2 Port.

To put Handset into programming mode:

Turn off handset, attach programming cable between device hirose port and PC then press red handset on/off button while holding PTT. The handset’s LED will light red.

To put Gateway into programming mode:
Turn off gateway. Then hold gateway ON/OFF button down while attaching the programming cable to device micro-USB port and PC USB port. The Gateway’s LED will light red. Note: The gateway’s RJ45 socket should not be connected to the host radio. Always READ device before proceeding further. We suggest you SAVE the file onto your PC for re-loading if required. A GREYED out feature means your device does support that capability.

• Read Device
  Press to load current programming parameters from device to screen.

• Program Device
  Press to load current screen programming parameters to a device.

• Restart (important)
  Press to restart programmed device before removing programming cable.

• Lock – Unlock File
  Press to lock your desired parameter configuration before undertaking batch fleet programming. This will prevent you errantly changing a parameter unknowingly during reprogramming.

• Load File
  Press to load a previously saved programming parameters to device from its saved PC location.

• Save File
  Press to save a programming parameters from screen to desired PC location saved location.

• Defaults
  Press to reset with default device parameters

• Exit
  Press to exit program.

• Radio PTT key beep
  Sounds talk permit two tone sequence whenever PTT is pressed and handset is within range of its gateway.

• Default – OFF
  Emergency key beep
  Sounds single tone whenever Emergency button is pressed and handset is within range of its gateway.

• Default – ON
  Talk around PTT key beep
  Sounds talkaround triple tone sequence whenever Talk around button is pressed and handset is within range of its gateway.
  Default – ON

• Stealth mode always active
  Disables all alert tones and LED status light. User can manually enable stealth mode if programmed off.
  Default – OFF

• Mute speaker on PTT
  Disables all speaker audio whenever PTT is pressed.
  Default – OFF

• Mute speaker on charge
  Disables speaker when handset is in gateway or a charger.
  Default – ON

• LED charge indicate
  Disables “momentary blink” charge indicate when handset is placed into
  gateway or a charger and device is charging.
  Default – ON

• Auto turn on when charging
  Causes handset to automatically turn on whenever it is placed in gateway
  or a charger.
  Default – ON

• Minimum volume is off
  Allows user to turn the speaker audio off instead of level 1.
  Default – OFF

• Mandown Monitor (when fitted)
  Enables/disables function via programmer for Plus handsets fitted with XMD option.
  Default – OFF

• Internal Mic Only Operation
  Maintains operation via internal microphone when accessory attached to Hirose port.required for earpiece (WPEH-X10/WPTEP-X10) use via Hirose headset port.
  Default – OFF

• Out of range turn off time
  Sets time in hours that a handset that is not actively connected to a gateway will remain powered on before turning itself off.
  Default – 8 hours

• Low battery beep voltage
  Sets the remaining battery voltage that will cause the low battery alert tones to be generated. (for longer shift life you may set voltage lower but you may get less warning before device automatically shuts off.
  Default – 3.5V

• Low battery beep interval timer
  Sets the interval that the low battery alert tones are sounded in the handset.
  Default – 5 minutes

• Elite Plus Only Options
  Handsfree Function (shows “disabled” if feature not enabled) Enables user selectable handsfree intercom function in Elite Plus handsets.
  Default – ON

• Toggle PTT/TA Button Assignment
  Configures handset so that pressing the top grey Control button toggles the side PTT button assignment between host radio PTT and Talkaround or 2nd Radio device PTT /PA Mode when used with XSJB or similar.
  Default – OFF

• Command Relay Mode / Automatic Relay Mode
  Selects the Relay Mode type in Elite Plus handsets.
  Default – Command Relay (manual – normally OFF)

Handset Programming: Audio Levels

We recommend you use the XGALA Gateway Audio Level Adjustment software tool for setting levels between host radio and X10DR gateway. It can be downloaded at www.x10dr.com/supports for setting audio in and out between the gateway and the host mobile radio. The following handset adjustments are designed to cater for different audio accessories and/or user applications requiring alternate audio sensitivities to suit different operating conditions.

• Internal Mic Gain
  Sets the internal microphone’s transmit audio level sensitivity.
  Default – 3

• Internal Mic High Gain Boost
  Sets the internal microphone’s sensitivity when “Live Mic” is active.
  Default – 6

• External Mic Gain
  Sets the external microphone’s transmit audio level sensitivity.
  Default – 6

• External Mic High Gain Boost
  Sets the external microphone’s sensitivity when the X10DR’s “Live
  Mic” is active or when user manually selects high gain by powering up
  microphone with blue volume up button pressed.
  Default – 6

• Remote PTT Gain Boost
  Increases sensitivity of internal microphone when remote/handlebar PTT is pressed.
  Default – 9

• Fixed Alert Tone Volume
  Limits all user monitored alert tones to level set below rather than being controlled by handset volume controls .
  Default – OFF

• Alert Tone Volume
  Sets the value of the “Fixed Alert Tone” when enabled that a user will hear from their handset.
  Default – 5

When handset is configured for press & hold emergency

Audio link active time
Sets the duration the transmit audio is active after Emergency button is released. Feature is intended for those mobiles that activate their own internal “Live Mic” function whenever emergency is triggered. This allows the handset’s Tx audio to be broadcast over the radio’s transmit channel, (assuming mobile sources “Live Mic” from its external mic input). Default – 0

When handset is configured for short/long press emergency

• Transmit Time
  Sets the time duration that X10DR “Live Mic” handset Tx audio is active when Advanced Emergency activated.
  Default – 0

• Receive Time
  Sets the time duration that X10DR “Live Mic” handset Rx audio is active when Advanced Emergency activated.
  Default – 0

• Emergency repeat cycles
  Sets the number of “Live Mic”, Tx and Rx cycles when Advanced Emergency is triggered.
  Default – 1

• Transmit audible emergency tone
  Causes an audible emergency warble tone to be transmitted over the host mobile radio channel when emergency is activated.
  Default – Off

• Hirose Pin 2 function
  Sets Hirose pin 2 to be either BAT+ (~3.3VDC) to power external accessories or bridged output speaker audio when pin 2 is set for speaker negative. Default – Speaker -VE

• Acc PTT
  Sets whether Hirose PTT input generates Talkaround or Radio PTT. Default – Radio PTT

• PTT
  Sets function of main large PTT button. Choose from drop down box. Default – Radio PTT

• Top 1
  Sets function of top left button. Choose from drop down box. Default – Emergency

• Top 2
  Sets function of top right button. Choose from drop down box. Default – Talkaround PTT

• Left 1
  Sets function of top left button.

• Default – short press Volume up / long press Relay mode OFF/ON (Elite Plus only)

• Left 2
  Sets function of bottom left button.
  Default – short press: Volume down

• Right 1
  Sets the function of right side button. Re-assigning requires hardware modifications.
  Default – short press: Search / long press: Power OFF/ON

• Long Press Duration
  Sets time button must be pressed to action a Long Press.
  Default – 5000mSec (Elite) 2000mSec (Pro)

Elite Plus Handset Right 1 Button – Short Press Assignments:

• Search – Resets connection to its paired gateway, other paired gateways or Relay Mode paired handsets LTE RSM On/Off – Toggles transmit function between configured X10DR functionality to a dedicated LTE (PoC) configured smartphone attached via curly cord – LED glows white when On. (For use with X10DR-EX2-LTE models only)
• Aux 1 (or 2) – Can be used to trigger Emergency when used with XFSB/ XSJB(V2) Smart boxes in dual radio deployments.
• Relay Mode On/Off – Toggles Relay Mode ON or OFF to allow handsets to talk directly or mesh back to vehicle when one handset is out of vehicle gateway range.
• Default – Search (Pro Plus Models can only access Search function)

Elite Plus Handset Right 1 Button – Long Press Assignments:

• On/Off – Manually powers Off and On the handset.
• Power On – Manually powers ON a handset that is OFF. When so assigned we suggest that the blue Volume Down button (L2) be programmed for Long Press: Power OFF for intuitive operation (other buttons can be chosen if desired). This assignment is suggested when short press is assigned other than to its default setting.
• Default – Off/ On

Elite Plus Handset Top 1/2, Left 1/2 Button – Short Press Assignments:

• Disabled – Button has no function
• Volume Up – Increases handset speaker audio volume in 7 steps.
• Volume Down – Decreases handset speaker audio volume in 7 steps.
• Aux 1 (or 2) – Can be used to trigger Emergency when used with XFSB/ XSJB(V2) Smart boxes in dual radio/ wireless device deployments.
• Emergency – Triggers Emergency on host mobile/wireless network device where available.
• HF On/Off – Toggles Handsfree local full duplex intercom operation ON / OFF.
• Relay Mode On/Off – Toggles Relay Mode ON / OFF to allow handsets to talk directly or mesh back to vehicle when one handset is out of vehicle gateway range.

Elite Plus Handset Top 1/2, Left 1/2 Button – Long Press Assignments:
as per above short press selection but with following addition assignable function:

• Power Off – Manually powers OFF a handset that is ON. (Suggested button assignment : Volume down (L2) button)

Gateway Parameters

We highly recommend use of the XGALA Gateway Audio Level Adjustment tool for setting audio levels. Download here: https://www.x10dr.com/supports

Gateway Programming: Audio Levels

• Receiver Input Gain From Radio
  Sets the receive input sensitivity. Default – 0

• Transmit Output Gain To Radio
  Sets the audio output level to radio when local/remote /handlebar PTT is pressed or when “Live Mic” is active. Default – 0

• Talk Around Output Gain to other X10DRs
  Sets the “intercom” microphone audio level. Default – 0

• Find Me™ Function
  Enables Find Me function in gateway. User double presses gateway Function button to trigger Find Me alert tones or triggers Remote FindMe.
  Default – OFF

• Radio Receive VOX/COR
  Enables VOX derived COR.
  Default – ON

• VOX Trigger Level
  Sets the gateway’s audio detect sensitivity for VOX derived COR. Default – 70

• Public Address Mode
  Sets the gateway so only handset Talkaround audio is sentto the gateway 3.5mm jack. When unchecked both Radio PTT and Talkaround audio is available for in- car monitor use. Default – OFF

• Monitor Emergency Input Alert Tone
  Causes Emergency warble alert tone to sound in all cross connected X10DR handsets whenever emergency input is triggered. (i.e. triggered from another gateway or externally supplied ground input). Default – OFF

• Trunking Support
  Enables speaker audio upon PTT for 500mS, so host trunked mobile’s Channel Grant /Talk Permit tones can be clearly distinguised by user. Handset Mic audio is also muted for 500mS to prevent those tones being rebroadcast over talkgroup. For optimum performance set VOX trigger level for 90-100 for fastest response. Default – OFF

Elite Plus Series Only Options

Multi Operational Mics
Allows two or three Elite Series Mics to be simultaneously operational through the one Elite gateway unit. Default – ON

Remote Find Me™
Enables Find Me function in gateway via grounding the white wire connected to pin 8 (Replaces Remote PTT function) Default – OFF

I/O
Defines whether the specific gateway interface pin is assigned as an input or an output.

Active
Sets whether the interface pin needs to be held low or pulled up high to activate assigned functionality. Function
Assigns desired functionality to Interface pin. Choose the desired input or output from the dropdown boxes.

Pulse
Defines the length of time an input must be activated before the function is triggered or alternatively how long an output is activated when the assigned function has been triggered. A value of zero means an input triggers instantly.

All rights reserved Wireless Corporation Limited ©2024
Wireless Pacific™, X10DR®, Liberate your mobile™, Find Me™, Powerfully Simple™ and their logos are trademarks or registered trademarks of Wireless Corporation Limited: Manual revision 1.5.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>