PACIFIC IMAGE ELECTRONICS Glite T8 Stand Alone Operation and Compact Gel Documentation System User Manual

Glite T8 Stand Alone Operation and
Compact Gel Documentation System
**User Manual

**

Product Content

• Glite T8
• User manual
• Gel shovel
• A/C Power Transformers(12V, 4.1A, DC)
• Amber Filter (in box)
• Black shading plate (in box)
• Gel cutter

Glite T8
Front

• Upper lid
• USB 2.0
• LCD Screen
• Power switch
• Light source switch

Interior

• Gel shooting area
• Upper lid sensor

Back

• DC power jack
• USB 2.0
• HDMI

Install & use

1. Remove all fixing tape.
1. Place the Glite T8 on a flat table.
1. Connect the power supply.
1. Press the power switch.
1. Insert the USB flash drive into the USB2.0 port on the front.
1. Put the gel into gel shooting area.
1. Adjust the image exposure value to a satisfactory condition and press the button to take a photo.

User Interface Instruction

Main screen

1. Capture****
2. ① Capture is the button that allows you to take photos and capture the gel imaging screen.
   

Click Capture, and after loading ends, you will be redirected to the setting screen after shooting.
Save – Save this result
Save all – Save all results
Rename – Can be renamed
Negative – Can be adjusted to invert effect
Print—Print result
Delete – Delete this result
Delete all – Delete all results
Zoom In/Out—Image zoom in/out
Return – Back to the main screen
Glite T8 support Sony thermal printer: UP-D898MD & UP-897MD

2. Exposure ② Exposure allows users to adjust the exposure level.
   Range: -10 to +10
   

3. B/G & WL epi, WL back③ B/G is to adjusted to Cyan’s light source using the switch on the front of the device.
   WL epi, WL back is to adjusted to White by the switch on the front of the device, and it has two modes: front light and backlight ← ※Notice: Click once to initiate the light source, and he background of the button would be white.
   

4. Continuous Capture

5. Setting ⑤ Setting contains a variety of different settings (see next page) Update S/W – Plug in the USB to update the software Mouse – You can connect a mouse to the USB port for operation

6. Image Viewer ⑥ Image Viewer allows you to browse the previously analyzed images, please refer to the explanation on p8 for the screen.

Cyan Dye Gel

1. Lift up the upper lid.
1. Slide the black shading plate (with the flannel side outward) into the rail to cover the white backlight plate of the upper cover.
1. Close the upper lid (if you need to open the cover to cut gel, observe or adjust the position, please use the amber filter, as shown in the right picture, see p23).
1. Switch the light source to Cyan.
1. If necessary, adjust the parameters through the Camera Tester in the Setting to obtain satisfactory image quality (please refer to p16).
1. Press the Capture button and the Loading icon will appear on the LCD panel.
The gel shooting process is complete.

To shoot fluorescent film images, please slide the black shading plate (with the flannel side outwards) into the rail to cover the white backlight plate of the upper cover to avoid reflections.

Use a white light source to shoot WESTERN BLOT/ and color gel film:

1. Shooting HRP/DAP WESTERN BLOT with WL epi
   1. Slide the black shading plate (with the flannel side outward) into the rail to cover the white backlight plate of the upper cover.
   2. Close the upper lid.
   3. Switch the light source to the White position.
   4. Set “WL epi” on the main screen.
   5. If necessary, adjust the parameters through the Camera Tester in the Setting to obtain satisfactory image quality (please refer to p16).
   6. Press the Capture key.

2. Use WL back to shoot SDS-PAGE gel with coomassie blue dye
   1. Pull out the black shading plate, do not cover the white backlight plate of the upper lid.
   2. Close the upper lid.
   3. Switch the light source to the White position.
   4. Set “WL back” on the main screen.
   5. If necessary, adjust the parameters through the Camera Tester in the Setting to obtain
   satisfactory image quality (please refer to p16).
   6. Press the Capture key.

Use amber filter

Glite T8 has an amber filter to facilitate the user to observe and cut blue or blue-green light excited gel
1. When you open the top lid, the blue or blue and green lights on both sides will automatically turn off
1. Push the upper lid to the highest
1. Hang the amber filter as shown on the right
1. After installing the amber filter, you can use the attached rubber cutting tool and press the camera button to start the blue/cyan light for gel cutting.

Project the screen to an external screen or projector
The operation screen of the machine can be projected to an external screen or projector through HDMI.

1. Set the TV or screen or projector to HDMI mode
2. Connect the HDMI cable to the video port of the TV or screen or projector
3. Connect the other end of the HDMI cable to the HDMI port on the back of the Glite T8
4. The operation screen of Glite T8 will be projected to the connected TV or screen or projector.

Product Specification

I. Instrument|
---|---
Image component| CMOS
Exposure time range| 21 levels
Image storage| USB
Gel shooting area| 16 x 10.5cm (Fixed lens)
II. Lens and filter|
---|---
Filter Turret| Manual-Driven, 2 position
Emission Filter| 518nm Amber Filter
III. Light|
---|---
Cyan light (GW)| 510 nm LED
Epi white light| White light LED
White light
backlight| White light LED backlight
VI. Interface|
---|---
Screen| 5” Touch TFT LCD
Internal storage| SD Card
Output| 1. USB 2.0 x2
2. HDMI out
V. Other information|
---|---
information| AC Adaptor, 12V/4.6A
Power| 22.9 x 20.7 x25.4cm (9.02 x 8.14 x 10 inches)
Size(WxHxD)| Amber filter
Gel cutting tool Weight| 3.2Kg (7.05 lb)
Safety certification| CE, FCC

Contact Information

For more information or any question, please contact :
PACIFIC IMAGE ELECTRONICS CO., LTD
7F, No. 239, SEC. 1, DATONG RD., XIZHI DIST.,
NEW TAIPEI CITY 221,
TAIWAN

TEL: +886 2 8692 1800
FAX: +886 2 8692 1860
sales@scanace.com.tw
www.scanace.com

Glite T8
Made in Taiwan
PACIFIC IMAGE ELECTRONICS CO., LTD
7F, No. 239, SEC. 1, DATONG RD., XIZHI DIST., NEW TAIPEI CITY 221, TAIWAN
TEL: +886 2 8692 1800
FAX: +886 2 8692 1860
www.scanace.com

Documents / Resources

| PACIFIC IMAGE ELECTRONICS Glite T8 Stand Alone Operation and Compact Gel Documentation System [pdf] User Manual
Glite T8, Stand Alone Operation and Compact Gel Documentation System, Glite T8 Stand Alone Operation and Compact Gel Documentation System
---|---

References

• Pacific Image Electronics Co., Ltd

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>