HUNTER PACIFIC SWM-IM-V1 Smart WiFi Module User Manual
- June 3, 2024
- HUNTER PACIFIC
Table of Contents
SMART WIFI MODULE USER MANUAL
SWM-IM-V1 Smart WiFi Module
WARNING – THIS PRODUCT MUST BE INSTALLED ONLY BY A LICENSED OR QUALIFIED ELECTRICAL WORKER. FAILURE TO FOLLOW THE WIRING RULES OR THESE INSTRUCTIONS MAY RESULT IN AN ELECTRICAL HAZARD. WARRANTY IS VOID UNLESS A CERTIFICATE OF COMPLIANCE OR A RECEIPT FROM A LICENSED INSTALLER IS AVAILABLE.
INSTALLING THE SMART WIFI MODULE
Remove the insert on your fan receiver and install the Smart WIFI Module.
No Light Fan Receiver
With Light Fan Receiver
SET UP THE SMART WIFI MODULE TUYA SMART APP
Before setting up the Smart WiFi Module with the Tuya Smart App, make sure you have the following:
- A Smart WiFi Module installed in your ceiling fan receiver and power to your fan
- A Wi-Fi router with active internet connection
- The wireless network name (SSID) and password of your router.
- Download the free Tuya Smart App by searching for Tuya Smart in your App store or by scanning the following QR code.
https://smartapp.tuya.com/tuyasmart
GET STARTED
- Open the Tuya Smart App and follow the instructions on the App to register/sign up & log in.
- Follow the prompts using a choice of either mobile phone number or email address.
- Turn on Wi-Fi on your mobile phone and ensure fan is in the same Wi-Fi area.
- Open your Tuya Smart App and choose “add device”. Device should be automatically and choose “add”.
- Select a 2.4GHz Wi-Fi network and entre password. If your Wi-Fi is 5GHz, it should also display a 2.4GHz version as a Wi-Fi option available, please set to the 2.4GHz option. Select “Next”.
- The device should be successfully added. To rename the device, click the “Pencil” button.
NOTE: If the setup fails, please reset the device to original setting and start again. To reset your fan if the set up has failed. Turn off your fan and turn on again with isolation switch and use the handpiece to do the programming by press and hold F/R button then the Smart Wi-Fi module is back to factory setting. When the reset is successful, the receiver will beep 2 times and if a light is fitted to the ceiling fan, it will flash twice. (Brian is checking)
For further instructions for how to install the Smart WiFi Module, please scan the QR code.
https://www.hunterpacificinternational.com/tuya
Maximise Product Life and Protect your Warranty
Damage caused by voltage or current surges will shorten the life of the
product and is not covered by warranty. Surges may be caused by lightning,
problems in the electricity network or out of specification voltages from
solar inverters. The chance of damage can be minimised by turning off the
isolation switch when fan is not being used. It is good practice to turn off
the isolation switch just like you would with a normal light switch.
Warranty Terms and Conditions:
This statement is required by the Australian Consumer Law 2010: “Our goods
come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.”
Hunter Pacific International Pty Ltd (HPI) will cover, for a period of 24
months (Residential) or 12 months (Commercial) from date of purchase,
replacement of the defective Pixie HPI Ceiling Fan Module.
**Warranty Procedure***
For online warranty bookings visit:
www.hunterpacific.com.au (24hours, 7 days)
For technical advice call: 1300 360 280 (Monday to Thursday from 9am to 5pm
EST / Friday from 9am to 4pm EST)
- Warranty only available within Australia
SWM-IM-V1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>