PACIFIC PERFORMANCE ENGINEERING 316119511 6.7L Power Stroke Up-pipes Kit Installation Guide

PACIFIC PERFORMANCE ENGINEERING 316119511 6.7L Power Stroke Up-pipes Kit

Product Information

Product Specifications

• Product Name: Ford 6.7L Power Stroke Up-pipes Kit (Left & Right)
• Compatible Vehicles:
  • 2011-2014 Ford F250/350 6.7L Power Stroke
  • 2015-2019 Ford F250/350 6.7L Power Stroke
  • 2020-2023 Ford F250/350 6.7L Power Stroke
• Part Numbers: 316119511, 316119515, 316119520

Product Usage Instructions

Installation Guide

1. Step 1: Turn off the vehicle and let it cool down. Disconnect the battery cables.
2. Step 2: Remove the front wheels and then the wheel well liners.

Step-by-Step Installation Process:

Additional Notes:
Make sure to follow all safety precautions and use appropriate tools for the installation process. Double-check all connections and fittings before starting the vehicle.

Frequently Asked Questions

Where can I find the GVWR rating and Engine Family information?

The GVWR rating is on the driver door jamb and the Engine Family is on the Vehicle Emission Control Information label under the hood.

Is the installation of the Up-pipes Kit legal in California?

It's legal only on vehicles with GVWR between 8,501 to 14,000 pounds and not on vehicles with specified Test Groups or Engine Families.

What if additional clearance is needed during the installation?

If more clearance is needed for the driver-side up-pipe, unbolt the transmission dipstick tube without removing it.

What should I do if I encounter issues with the product?

For any concerns or warranty claims, contact PPE with the proof of purchase. If installation is in doubt, consult the manufacturer.

Ford 6.7L Power Stroke Up-pipes Kit (Left & Right)

• 2011-2014 Ford F250/350 6.7L Power Stroke
• 2015-2019 Ford F250/350 6.7L Power Stroke
• 2020-2023 Ford F250/350 6.7L Power Stroke
• (316119511, 316119515, 316119520)

IMPORTANT NOTE

• It is not legal in California to install the product on vehicles with the following Test Groups or Engine Families: BFMXH06.7A24, CFMXH06.7A24, DFMXH06.7A24, FFMXH06.7A24, GFMXH06.7A24, GFMXH06.7P4B,
• HFMXH06.7P4B, JFMXH06.7P4B, KFMXH06.7P4B, LFMXH06.7P4B, MFMXH06.7P4B, NFMXH06.7P4B, PFMXH06.7P4B.
• The product is only legal in California to be installed on vehicles with 8,501 to 14,000 pounds gross vehicle weight rating (GVWR).
• The Test Group or Engine Family can be found on the Vehicle Emission Control Information label located under the hood.
  The GVWR rating can be found on the driver door jamb.

PACKAGE CONTENTS

• A. (1) Driver Side Up-Pipe
• B. (1) Passenger Side Up-Pipe
• C. (2) Gasket

INSTALLATION

• Step 1. Turn the vehicle off and allow time to cool down before installing. Disconnect the cables from the battery.
• Step 2. Remove the front wheels, followed by the wheel well liners.
• Step 3. From the passenger side, remove the two 13mm nuts securing the downpipe bracket to the engine block, and the nut to the clamp securing the downpipe to the turbo elbow. Fig.3
• Step 4. Remove the two 13mm bolts securing the downpipe to the remainder of the exhaust system Fig.4
  • Step 5. Loosen and detach the bracket that secures the transmission cooler lines to create sufficient space for downpipe removal. Plug lines to prevent trans fluid leakage. Fig.5
• Step 6. Remove the downpipe by rotating it out between the transmission and the frame rail. Fig.6
• Step 7. Remove the 13mm bolt securing the turbo outlet bracket to the transmission, and the 11mm nut to the v-band clamp secured to the turbo. Fig.7
• Step 8. Pry the v-band clamp open and remove the turbo outlet. Fig.8
• Step 9. Remove the following sensors from the passenger side factory up-pipe through the engine bay:
  • Remove the EGT sensor and place it to the side. Fig.9
  • To remove the exhaust back pressure sensor tube, start by loosening the nut that holds the bracket in place. After that, loosen the flare nut that secures the tube. Next, detach the tube from the up-pipe and set it aside. Fig.10
• Step 10. To remove the up-pipe loosen the 11mm nut that secures the v-band clamp. Once loosened, carefully detach the clamp. Next, proceed to remove the three 13mm nuts securing the up-pipe to the manifold. Fig.11
• Step 11. Begin the driver-side up-pipe removal by loosening the 11mm nut to the v-band clamp and removing the two 13mm flange nuts behind the shroud. Fig.12
• Step 12. Move over to the driver-side wheel well to gain access to the third nut securing the up-pipe to the manifold. We used a long extension with a swivel and slid it between the transmission bell housing and firewall to remove this final nut. Fig.13
• Step 13. Begin by installing the driver-side PPE up-pipe, ensuring to use the supplied gasket along with the original 13mm nuts and v-band clamp. Similarly, install the passenger side PPE up-pipe, utilizing the supplied gasket along with the original 13mm nuts and v-band clamp Fig.14
  • Lastly, reattach the EGT sensor and EBP sensor tube into the newly installed PPE up-pipe Fig.15
  • NOTE: For the installation of the driver-side up-pipe, if additional clearance is needed, unbolt the transmission dipstick tube (do not remove)
• Step 14: Reinstall the factory turbo outlet, downpipe, transmission cooler lines, both fender well liners, and wheels.
• Step 15: Place the supplied CARB E.O. label on a clean, visible location under the hood. PPE recommends using the top side of the fan shroud.

This completes the installation.

DISCLAIMER OF LIABILITY

Performance products can increase horsepower above and beyond factory specifications. Additional horsepower creates more stress on the drive-train components, which could result in drive-train failure. Note regarding emissions-related, non-E.O.-legal products: THESE PRODUCTS ARE LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR REGISTERED OR LICENSED FOR HIGHWAY OR OFF-ROAD USE.

This agreement sets forth the terms and conditions for the use of PPE products. The installation of this product indicates that the Buyer has read and understands this agreement and accepts the terms and conditions. PPE (Pacific Performance Engineering) Inc., its distributors, employees, and dealers (the “Seller”) shall not be responsible for the product’s proper use and service. The buyer hereby waives all liability claims. The Buyer hereby acknowledges no reliance on the Seller’s skill or judgment to select or furnish goods suitable for any particular purpose and that there are no liabilities that extend beyond the description on the face hereof, and the Buyer hereby waives all remedies or liabilities expressed or implied, arising by law or otherwise (including without any obligation of the Seller to fitness, merchantability and consequential damages), or whether or not occasioned by the Seller’s negligence.

The Seller disclaims any warranty and expressly disclaims any liability for personal injury or damages. The Buyer acknowledges and agrees that the disclaimer of any liability for personal injury is a material term for this agreement and the Buyer agrees to indemnify the Seller and to hold the Seller harmless from any claim related to the item of equipment purchased. Under no circumstances will the Seller be liable for any damages or expenses because of the use or sale of any such equipment. The Seller assumes no liability regarding the improper installation or misapplication of its products. It is the installer’s responsibility to check for proper installation and if in doubt, contact the manufacturer. The Buyer is solely responsible for all warranty issues from the manufacturer.

LIMITATION OF WARRANTY

The Seller gives Limited Warranty as to description, quality, merchantability, and fitness for a particular purpose, productiveness, or any other matter of Seller’s product sold herewith. The Seller shall not be responsible for the product’s proper use and service and the Buyer hereby waives all rights other than those expressly written herein. This warranty shall not be extended, altered or varied except by a written instrument signed by Seller and Buyer.

Limited lifetime warranty on all PPE cast aluminium products and PPE VXZmission Coolers. Three (3) year limited warranty on PPE Manifolds and Up- Pipes Kits, and OEM-Length Up-Pipes. One (1) year limited warranty on all other PPE products from the date of sale to the original buyer and limited solely to the parts contained within the product kit. All products that are in question of Warranty must be returned prepaid to the Seller and must be accompanied by a dated proof of purchase receipt. All Warranty claims are subject to approval by the Seller. Under no circumstances will the Seller be liable for any labour charged or travel time incurred in diagnosis for defects, removal, or re-installation – of this product or any other contingent expenses. Under no circumstances will the Seller be liable for any damage or expenses incurred because of the use or sale of any such equipment. If the buyer does not agree with this agreement: the buyer may promptly return this product, in a new and unused condition in its original packaging, with a dated proof of purchase to the place of purchase within ten (10) days from the date of purchase for a full refund. The installation of this product indicates that the buyer has read and understands this agreement and accepts its terms and conditions.

PPEpower.com.

References

• Pacific Performance Engineering

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>