HARVEST 700 Series Moisture Sensor Kit Installation Guide

September 12, 2024
Harvest

700 Series Moisture Sensor Kit

“`html

Specifications:

  • Model: 700
  • Product Name: Moisture Sensor Kit 700 Series
  • Compatibility: New Holland 590-BB960, BB9060-BB9080 & Case
    IH LBX 331-431, LB333-LB433

Product Usage Instructions:

Introduction:

Thank you for purchasing the Harvest Tec moisture monitor
system. This system can be operated through various displays and
tablets using the Precision Baling App.

System Requirements:

Compatible with Harvest Tec Display, Baler Integration, or
Tablets. Ensure all displays have the latest operating system for
optimal performance.

Tools Needed:

  • Standard Wrench set
  • Side cutter
  • Standard Socket Set
  • Electric drill and bits
  • Hammer
  • Center punch

Installation of the Processor (IPM) on standard balers:

Mount the Main Processor (IPM) onto your baler by following the
instructions provided in the manual. Ensure proper installation to
avoid water damage.

Installation of Main Wire Harness Routing and Connections:

Follow the manual instructions to route and connect the main
wire harness properly for efficient functioning of the system.

Installation of Star Wheel Moisture Sensors:

  1. Locate the star wheel moisture sensors and twine
    diverters.

  2. Place the star wheels close to the knotter as instructed.

  3. Install the Allen head cap screws as per the guidelines
    provided.

Installation of End of Bale Sensor:

Mount the end of bale sensor on your baler to determine needle
position and communicate necessary information to the controls.
Trim excess metal after installation.

FAQ:

Q: Where can I order parts for the system?

A: You can view the Parts Breakdown in the manual and contact
your local authorized dealer to order the required parts.

“`

Installation Manual
Model 700
Moisture Sensor Kit 700 Series

700-24-INST-Imp&Metric

6/24

1

2

Table of Contents
Introduction System Requirements Tools Needed Installation of Moisture Sensor Kit
Installation of Processor (IPM) Installation of Main Wire Harness Installation of Star Wheel
New Holland 590-BB960, BB9060-BB9080 & Case IH LBX 331-431, LB333-LB433
Challenger LB33, LB34, Hesston 7430, 4750, 4755, 4760, 4790, Massey Ferguson 2050, New Idea 7233, 7333, 7234 Hesston 4900, 4910, Challenger LB44 & New Idea 7244 Claas 2100 & 2200 Claas 3200 ­ 3400, 5300 Krone Large Square Balers Kuhn, Vicon and Taarup Balers Installation of End of Bale Sensor Hesston 4760 ­ 4790 and equivalents, Case IH LBX 331 ­ LB 433, Class 2100, John Deere 100, New Holland 590 ­ BB 9080, Hesston 4750 ­ 4755 & 4900 ­ 4910 Krone 890-12130, Kuhn, Vicon and Taarup Balers End of Bale Sensor Bracket Installation Hesston 4750-4755 and 4900-4910 Hesston 4760 and 4790 Claas 2100, 3200-3400 and 5300 John Deere 100 Krone 890-1290 Krone 12130 Kuhn, Vicon and Taarup Balers Tractor Setup Display Options Optional Harvest Tec Display Optional Tablet Display Wiring Diagram Pin Outs Parts Breakdown Star Wheel Sensors & Moisture Harness Control Box and Wiring Harnesses End of Bale Sensor Kit Notes Warranty Statement

PAGE 4 4 4
4-21 4 5
6-12
6
7
8 9 10 11 12 13-14
13
13 14 15-21 15 16 17 18 19 20 21 22 23 23 23 24 25-27 28-29 28 29 29 30 31

3

Introduction
Thank you for purchasing a Harvest Tec moisture monitor system. This moisture monitoring system has been designed to be operated through a number of different displays and tablets using the Precision Baling App. These options include: iOS/Android Tablet, the Harvest Tec display, tractor ISO display (requires additional adapter 006-7670A), or the baler’s ISOBUS and display on the baler monitor (integration with baler ISO system required, call HT for details).
The 700 Series Moisture System is designed to show moisture through the balers ISOBUS. Failure to follow instructions can result in personal injury or equipment malfunction. If you need parts for the system, please view the Parts Breakdown toward the back of this manual and contact your local authorized dealer to order the parts.

System Requirements
Made for Harvest Tec Display, Baler Integration, or Tablet For best performance ensure all displays are running the latest operating system

Tools Needed Standard Wrench set Side cutter Standard Socket Set

Electric drill and bits Hammer Center punch

Installation of the Processor (IPM) on standard balers

Follow the instructions below to mount the Main

Processor (IPM) onto your baler. The locations shown are

on the right twine box (looking form the back of the baler).

Mark and drill the two 3/8 (10mm) holes and install the

(IPM) with two 5/16 x 1 bolts, four 1/4″ washers, and two

5/16″ nylock nuts. Main harness whip coming out of (IPM) should point to the ground. When attaching

8.13″

other harness make sure to loop them below the (IPM) so

as not to funnel water into the control.

14.5″

5″

4

Installation of Main Wire Harness Routing and Connections
Route harness 006-765B2 along this path or similar on top of or inside of the baler from control box on the twine box to the front of the baler. Note: the end of the harness that has the large plug with sockets and the white heat shrink label, will be at the hitch of the baler. The other end attaches to the control box. Keep harnesses away form moving parts and hydraulic hoses. Identification of plugs on 006-765B2 Sol 1 and Sol 2. Plugs. These attach to the solenoids with two 006-3650-S1 harness. Sol 1 attaches to the solenoid with a white dot. Sol 2 attaches to the solenoid with a blue dot. (Not used on moisture only) EOR Plug (end of row) is for the “Optional” crop eye kit. (474C) CAN/IDM Plugs are for use with “Optional” Moisture Dye Marking kit. (740DM), ISOBUS integration with compatible balers, future expansion, or CAN termination. EOB Plug is for the (end of bale) sensor that is attached by the needle arm. Secure with existing cable clamps or use cable ties when all connections are made.
Installation of Star Wheel Moisture Sensors 1. Locate the two-star wheel moisture sensors (030-4642U / UE) and twine diverters (001-4644 / 4645) 2. The star wheels will be place as close to the knotter as possible. Refer to the following pages for your
exact make and models installation instructions. 3. Install the four (two per side) 5/16″ x 3″ Allen head cap screws. Make sure the Allen heads are in the bale
chamber. 4. The star wheel with the 6-position plug will need to be placed on the right side of the baler along with the
twine diverter with two extra holes. 5. The star wheel with the 2-postion plug will need to be placed on the left, or ladder side of the baler 6. Secure the star wheels and twine diverters to baler with four 5/16″ hex nuts and lock washers. 7. Connect moisture harness (006-7307EM3) to both star wheels. 8. Run other end of (006-7307EM3) along top of baler back to the pump module located on the tank saddle. 9. Attach rectangle plug to bottom of pump module. The following pages will contain detailed instructions for specific baler makes and models.
5

New Holland 590 through BB9080 and Case IH LBX331 through LB433 Balers Star Wheel Mounting – The star wheels are to be mounted on top of the baler, just behind the knotters and under the walkway on both sides. Remove the bale from the chute, tip the walkway up and locate the wheels on the top outside corner angles of the bale chute, one on each side. Some balers may already have the notch cut and square holes. If so, the holes will need to be drilled round with a 5/16″ drill bit, if not use the template located in the back of the manual as a guide for cutting the notch and mounting holes for the star wheels. Mark the location of the notch 5/8″ wide and 9″ long (16mm x 23cm) and the location of the two 5/16″ (8mm) holes for the star wheel base. After cutting the notch and drilling the holes, insert the 5/16″ x 3″ x black allen head bolts up through the chute. Place the star wheel block over the bolts and install the twine guards. Secure with 5/16″ lock washers and nuts. The twine guard containing the extra two holes will be placed on the right side.
6

Challenger LB33, LB34, Hesston 7430, 4750, 4755, 4760, 4790, Massey Ferguson 2050, New Idea 7233, 7333, 7234 Star Wheel Mounting ­ The star wheels are mounted under the walkway on top of the baler behind the knotters. Remove the bale from the chute and tip the walkway up. Locate the outside corner angles of the bale chute on the left and right side of the baler. The center of the wheel shaft will be approximately 5-1/2″ (13cm) in front of the walkway support or about halfway between the walkway support and the cross frame almost directly in front of it. The notch will start just in front of the walkway support. Two parts of the baler frame will have to be trimmed off on both sides to mount each star wheel. The first is the outside corner angles of the chute. Use the template to mark the location of the star wheel notch as well as the location of the two holes for the star wheel base. The notch will be 5/8″ by 9″ (16mm x 23cm) long and will help keep the wheel away from the twine. Spray the ground off areas with touch up paint to prevent rusting. The second portion of the baler to trim off is the end of the gusset that may interfere with the star wheel’s plastic base support. Center the star wheel in the slots that was just notched and check for interference with the gusset. Drill 5/16″ (8mm) holes for the star wheel block. Insert the 5/16″ x 3″ bolts up through the chute. Place the star wheel block over the nuts and install the twine guards. Secure with 5/16″ Lock washers and nuts. The twine guard containing the two extra holes will be placed on the right side of the baler.
7

Hesston 4900, 4910, Challenger LB44, and New Idea 7244 Star Wheel Mounting ­The star wheels are mounted on top of the baler, just behind the knotters under the walkway on both sides. Use the template at the back of the manual to mark the location and dimension of the notch and holes. Remove the bale from the chute. Tip the walkway up and locate the wheels on the top outside corner angles of the bale chute, one on each side. The star wheel block is located just in front of the horizontal channels holding the twine boxes. Using the template, mark the location of the notch (5/8″ wide and 9″ long) and the location of the two 5/16″ (8mm) holes for the star wheelbase using a center punch. Any bare metal edge of the angle should be sprayed with touch up paint to prevent corrosion. Once the above modification to the baler is made on both sides of the chute, the wheels can be mounted. Insert the 5/16″ x 3″ bolts up through the chute and use nuts to hold the bolts in place. Place the star wheel block over bolts and install the twine guards on the star wheel block. The twine guard containing the two extra holes will be on the right side of the baler.
8

Claas 2100 and 2200 Star Wheel Mounting ­ The star wheels are to be mounted on top of the baler, just behind the knotters and as far forward as possible. Remove the bale from the chute. Locate the wheels on the top outside corner angles of the bale chute, one on each side. Use the template located in the back of the manual as a guide for cutting the notch and mounting holes for the star wheels. Mark the location of the notch 5/8″ wide and 9″ long (16mm x 23cm) and the location of the two 5/16″ (8mm) holes for the star wheel base. After cutting the notch and drilling the hole, insert the 5/16″ x 3″ black Allen head bolts up through the chute. Place the star wheel block over the bolts and install the twine guards. Secure with 5/16″ lock washers and nuts. The twine guard containing the extra two holes will be placed on the right side.
.
9

Claas 3200-3400, 5300 Large Square Balers continued Star Wheel Mounting ­ Use the picture below as a guide for drilling the mounting holes for the star wheels. The star wheels are to be mounted on the side of the bale chamber, between the top and middle channel. Measure 10″ back from the hinge between the top and middle channel. Use the template located in the back of the manual as a guide for cutting the notch and mounting holes for the star wheels. Cut 1″ x 9″ (25mm x 23cm) slot for the star wheel. Make sure the wheel is square. Mark the location of the two 5/16″ holes for the star wheel base. After drilling the holes, insert the 5/16″ x 3″ allen head bolts through the chute. Place the star wheel block over the bolts and install twine guards on the star wheel. Secure with 5/16″ lock washers and nuts. The twine guard containing the extra two holes will be
placed on the right side.
10

Krone Large Square Star Wheel Mounting-non-HDP models remove the bale for the bale chute. The star wheels are to be mounted on top of the baler, just behind the knotters and as far forward as possible. Use the table and diagram below to mark the two bolt hole locations on the bale chamber (D,E,F). Use the template in the back of the manual to mark the location of the notch to be cut. When cutting the notch both the vertical brace and the bale chamber will need to be cut. Before cutting verify the notch measurement with the below diagram using marks A & B. After cutting the notch and drilling the holes, insert the 5/16″ x 3″ black Allen head bolts up through the chute. Place the star wheel block over the bolts and install the twine guards. Secure with 5/16″ lock washers and nuts. The twine guard containing the two extra holes will be placed on the right side. For 2010 Krone HDP part number 20 073 194 0 must be ordered. This kit will include mounting instructions for the star wheels.
Krone balers 890 ­ 12130 A= 2-3/4″ (69mm) from edge of notch B= 3-1/2″ (89mm) D= 3″ (76mm) E= 5-3/4″ (77mm) from edge of notch F= 8-3/4″ (22cm) from edge of notch
11

Kuhn LSB 870 ­ 1290, Vicon LB 8200 and LB 12200, Taarup 6570 ­ 6690 OC Star Wheel Mounting-. The star wheels are to be mounted on top of the baler, just behind the knotters and under the walkway on both sides. Remove the bale from the chute, mount the star wheels flush with the back of the walkway with one star wheel on each side. Use the template in the back of the manual labeled Vicon large square balers for this installation Mark the holes inside the chamber, and drill the two holes per side, for mounting from inside the chamber. Insert the 5/16″ x 3″ black Allen head bolts up through the chute. Place the star wheel block over the bolts and install the twine guards. Secure with 5/16″ lock washers and nuts. The twine guard containing the two extra holes will be placed on the right side.
12

Installation of End of Bale Sensor
The end of bale sensor determines the position of the needles on the baler. When the needles cycle the sensor communicates this information to the controls. This information is used for job records and will be used by the optional Bale Identification System. Follow the steps below for your baler to mount the sensor.

All AGCO Hesston 4760 ­ 4790 and equivalents, Case IH LBX 331 ­ LB 433, Class 2100, John Deere 100, New Holland 590 ­ BB 9080
End of bale sensor bracket (001-4648) will be used. Cutoff excess metal not used during installation.

001-4648 with 6″ (15cm) hole used for sensor

001-4648 with 12″ (30cm) hole used for sensor

All Hesston 4750 ­ 4755 & 4900 ­ 4910 End of bale sensor bracket (001-4648) and Hesston end of bale mount (001-4648H) will be used. The Hesston end of bale mount will be found in the installation kit box. Cutoff excess metal not used during installation.
001-4648 with 6″ (15cm) hole used for sensor
001-4648H mount
13

All Krone 890 ­ 12130
Krone end of bale sensor bracket (001-4648K or 001-4648K2) be used. The Krone end of bale mount will be found in the installation kit box. The 001-4648K will be used with balers 890 ­ 1290. The 001-4648K2 will be used with the 12130 balers.

001-4648K

001-4648K2

All Kuhn, Vicon and Taarup Balers End of bale sensor bracket (001-4648) will be used. Cutoff excess metal not used during installation.

001-4648 with 6″ (15cm) hole used for sensor

001-4648 with 12″ (30cm) hole used for sensor

14

End of Bale Sensor Bracket Installation Hesston 4750-4755 and 4900 ­ 4910

Sensor hole location 7″ (18cm)

A

B

C

7-7/8″ 9-5/8″ 5/8″ (20cm) 25cm) (16mm)

Attach the Hesston end of bale mount (001-4648H) as shown. Attach the end of bale sensor bracket (0014648) to the Hesston end of bale mount (001-4648H) using two 1/4″ x 1″ bolts, locks & flat washers, and hex nuts. Align the brackets and mark the two 3/8″ (10mm) holes to be drilled. Attach the brackets to the baler using two 5/16″ x 1 self-tapping screws, and flange nuts.
Mount the sensor in the 7″ (18cm) hole location, keep the sensor 1/4″ (7mm) from the needle and tighten both nuts. Cut off excess metal past the sensor. Run the sensor cable up to the main harness (006-765B2) and attach to port labeled EOB.

15

Hesston 4760 and 4790

Hesston 4760
Baler 4760 4790

Hesston 4790

Sensor hole location

A

B

C

6″

6-5/8″ 4-7/8″ 4″

6″

4-5/8″ 2-7/8″ 3″

Mount the end of bale sensor bracket (001-4648) as shown. Mark and drill two 3/8″ holes and attach the bracket using two 5/16″ x 1″ self-tapping screws, and 5/16″ flange nuts. Mount the sensor in the 6″ (15cm) hole location, keep the sensor 1/4″ (7mm) from the needle and tighten both nuts. Cut off excess metal past the sensor. Run the sensor cable up to the main harness (006-765B2) and attach to port labeled EOB.

16

Claas 2100

Sensor hole location 8″ (20cm)

A

B

C

5-3/4″ 4″

5/8″

(13cm) (10cm) (16mm)

Mount the end of bale sensor bracket (001-4648) as shown. Mark and drill two 3/8″ (10mm) holes and attach the bracket using two 5/16″ x 1″ self-tapping screws, and 5/16″ flange nuts. Mount the sensor in the 8″ (20cm) hole location, keep the sensor 1/4″ (7mm) from the needle and tighten both nuts. Cut off excess metal past the sensor. Run the sensor cable up to the main harness (006-765B2) and attach to port labeled EOB.

Claas 3200-3400, 5300

001-4648C

The end of bale (EOB) sensor mounts in the EOB bracket (001-4648C) as shown in the picture. The EOB bracket is mounted to the top side of the needle arm stop using the existing hardware that secures the bumper to the stop.
17

John Deere 100

Sensor hole location 6″ (15cm)

A

B

C

2-5/8″ 7/8″

7″

(70mm) (22mm) (18cm)

Mount the end of bale sensor bracket (001-4648) as shown. Mark and drill two 3/8″ (10mm) holes and attach the bracket using two 5/16″ x 1″ self-tapping screws, and 5/16″ flange nuts. Mount the sensor in the 6″ (15cm) hole location, keep the sensor 1/4″ (7mm) from the needle and tighten both nuts. Cut off excess metal past the sensor. Run the sensor cable up to the main harness (006-765B2) and attach to port labeled EOB.

18

Krone 890 ­ 1290

Sensor hole location N/A

A

B

C

2-1/4″ 1/2″

8″

(65mm) (13mm) (20cm)

Mount the Krone end of bale sensor bracket (001-4648K) as shown. The Krone mounting bracket can be found
in the installation kit box. Mark and drill two 3/8″ (10mm) holes and attach the bracket using two 5/16″ x 1″ selftapping screws, and 5/16″ flange nuts. Mount the sensor at the end of the bracket, keep the sensor 1/4″ (7mm) from the needle and tighten both nuts. Run the sensor cable up to the main harness (006-765B2) and attach to
port labeled EOB.

19

Krone 12130
Mount the Krone end of bale sensor bracket (001-4648K2) as shown. The Krone mounting bracket can be found in the installation kit box. Directly behind the twine box on the right side of the baler remove the bolt and nut that secures the fiberglass baler shield to the baler. Mount the sensor bracket using the 3/8 x 1 bolt, lock and nut. Mount the sensor at the end of the bracket, keep the sensor 1/4″ (7mm) from the needle and tighten both nuts. Run the sensor cable up to the main harness (006-765B2) and attach to port labeled EOB.
20

Kuhn, Vicon and Taarup Balers
Mount the end of bale sensor bracket (001-4648) as shown. Mark and drill two 3/8″ holes and attach the bracket using two 5/16″ x 1″ self-tapping screws, and 5/16″ flange nuts. Mount the sensor in a hole location centered over the needle arm, keep the sensor 1/4″ (7mm) from the needle and tighten both nuts. Run the sensor cable up to the main harness (006-765B2) and attach to port labeled EOB.
21

Tractor Setup

The general tractor setup of the 700 Series applicator can be seen above. The main harness of interest is the tractor power/communication harness (006-765IC). This harness will connect at the tractor battery, to the ISO Communication Module (ICM) mounted in the cab, a keyed power connection point, and connect at the hitch area to the baler power/communication harness (006-765B2). View below to see highlighted installation instruction:

12V Battery Connection

The 12V battery connection must be at the tractor battery. Connection to alternative locations such as an accessory port can cause problems with applicator system.
MUST BE CONNECTED DIRECT TO TRACTOR BATTERY TERMINALS

ISO Communication Module

The ISO communication module is to be mounted inside the cab. Other mounting locations can lead to issues with weathering and operation. Once installed and the system is powered, a green light will turn on with the ICM module.

Key Power Connection

Ensure a solid keyed connection is found inside the cab and wired into. Poor keyed power connection can result in applicator system issues.

Harness Connection to Baler

The tractor harness connects at the hitch to baler power/communication harness (006-765B2). This will allow the system components to communicate with one another. Ensure connections are debris and corrosion free.

22

Display Options Optional Harvest Tec Display
The 700 series Harvest Tec Display will allow you to set your real time baling parameters to ensure the most precise application to every bale. This is done by utilizing the improved touch technology to select objects, enter data, and swipe through operational screens. The Harvest Tec Display offers easy integration by connecting to the additional CAN plug on the 006-765IC harness. Once, connected the Harvest Tec display will power up with applicator system. Note: The Harvest Tec Display must be used as a standalone display, the baler cannot run both integrated and on the Harvest Tec Display. Must be one or the other. Removal of the 006-765VA or integration harness is required when equipped. Optional Tablet Display
Precision Baling App
The iOS or Android Tablet displays offer the ability to communicate with the 700 series applicator system via hard-wired connection to the ISO Communication Module (ICM). Through the free Precision Baling App, the operator can set real time baling parameters to ensure the most precise application to every bale. This provides a multi-use option while utilizing the improved app to select objects, enter data, and easily switch through operational screens. The Tablet Display offers easy integration by connecting a charging cable to the USB port on the ICM module. Once connected the Harvest Tec applicator will display upon opening the app and powering up the applicator system. Tablets can be used in addition to integrated baler VT display.
Made for iPad® (3rd generation minimum) or Android Tablet (Does not work with Amazon Fire). iPad is a trademark of Apple Inc., registered in the U.S. and other countries.
23

Wiring Diagram ­ 700 Series
1. Connect the power harness (006-765IC) to the tractor battery (12 volt) using the red wire with fuse to the positive side and the black wire to the negative. A. The power harness must be connected to the battery! CONTACT HARVEST TEC BEFORE MODIFICATIONS. The unit will draw more amps than convenience outlets can handle. Any modifications of the power harness will void systems warranty B. This unit will not function on positive ground tractors. C. If the unit loses power while operating it will not keep track of accumulated pounds of product used.
2. The power harness on the tractor (006-765IC) will run from the tractor battery to the hitch. The power harness on the baler (006-765B2) will connect to the tractor power harness (006-765IC) at the hitch.
3. Connect the keyed power wire (006-765CPH) to a keyed power source on the tractor. The keyed power wire must connect to a keyed source or the unit will not power up correctly.
4. Attached the ISO Communication Module (006-6673) to the tractor power harness (006-765IC). 5. Attach the End of Bale (EOB) connection on baler harness (006-765B2) to the EOB Sensor (006-7401). 6. Attach star wheel (030-4642U/UE) connection to the IPM

Optional Harvest Tec Display Harness 006-765GH
Key Power Harness 006-765CPH

ISO Communication Module (ICM) 030-6673

Power Harness on Tractor 006-765IC

Power Harness on Tractor 006-765B2

Active Terminator Required on one Can/IDM port Only (for Non-ISO connections)
006-700R
End of Bale Sensor 006-7401

Moisture Harness 006-7303EM3

700 ISO Pump Module 006-7671LS
Star Wheels 030-4642 (U/UE)

24

Pin Outs

Integrated Control Module (ICM) on Tractor Harness 006-765IC
(Deutsch Plug Number: DTM06-12SA)

Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12

Red Purple Red/White Black/White Orange Blue Green Yellow White Gray Brown Black

+12V from ECU Signal Wire +12V CAN X Ground CAN X CAN X Hi CAN X Lo ISO CAN Lo ISO CAN Hi GPS Expansion 1 GPS Expansion 2 GPS Expansion 3 Ground from ECU

12 3456 12 11 10 9 8 7

ISOBUS Plug on Tractor Harness 006-765IC
(Deutsch Plug Number: DT04-4P)

Pin 1 Pin 2 Pin 3 Pin 4

Red Yellow Green Black

+12V from ECU ISO CAN Hi ISO CAN Lo Ground from ECU

1

3

2

4

Power / Communication Tractor Harness 006-765IC at Baler Hitch
(Deutsch Plug Number: HDP24-24-18PN)

Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 Pin 16 Pin 17 Pin 18

Not Used Yellow Green Red Black Red Not Used Black Not Used Purple Red/White Black/White Orange Blue White Gray Brown Not Used

—ISO CAN Hi ISO CAN Lo +12V Power to ECU Ground to ECU +12V From Battery —Ground From Battery —Signal Wire +12V CAN X Ground CAN X CAN X Hi CAN X Lo GPS Expansion 1 GPS Expansion 2 GPS Expainsion 3 —-

25

Pin Outs (continued)

Power / Communication Baler Harness 006-765B2 at Baler Hitch
(Deutsch Plug Number: HDP26-24-18SN)

Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 Pin 16 Pin 17 Pin 18

Not Used Yellow Green Red Black Red Not Used Black Not Used Orange/White Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used

—ISO CAN Hi ISO CAN Lo +12V Power to ECU Ground to ECU +12V From Battery —Ground From Battery —+12V Power to EOR ————————-

Power / Communication Baler Harness 006-765B2 at IPM Module
(Deutsch Plug Number: HDP24-24-18SN)

Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 Pin 16 Pin 17 Pin 18

Not Used Yellow Green Red Black Red Not Used Black Not Used Orange/White Orange/Black Purple/Green Blue/White Gray/Red White/Black Orange/Red White/Black Not Used

—ISO CAN Hi ISO CAN Lo +12V Power to ECU Ground to ECU +12V From Battery —Ground From Battery —+12V Power to EOR Ground to EOR EOR Signal EOB Signal +12V Power to Solenoid 1 Ground to Solenoid 1 +12V Power to Solenoid 2 Ground to Solenoid 2 —-

Solenoid 1 Plug on Baler Harness 006-765B2
(Deutsch Plug Number: APTIV 12052641)

Pin B Pin A

Gray/Red White/Black

+12V to Solenoid 1 Ground to Solenoid 1

Solenoid 2 Plug on Baler Harness 006-765B2
(Deutsch Plug Number: APTIV 12052641)

Pin B Pin A

Orange/Red White/Black

+12V to Solenoid 2 Ground to Solenoid 2

26

A

B

Pin Outs (continued)

CAN / IDM on Baler Harness 006-765B2
(Deutsch Plug Number: DT06-4S)

Pin 1 Pin 2 Pin 3 Pin 4

Red Yellow Green Black

+12V to ECU ISO CAN Hi ISO CAN Lo Ground to ECU

End of Bale Sensor Plug on Baler Harness 006-765B2
(Deutsch Plug Number: DT06-3S)

Pin 1 Pin 2 Pin 3

Orange/White Orange/Black Blue/White

+12V to End of Bale Sensors Ground to End of Bale Sensors Signal

End of Row Sensors Plug on Baler Harness 006-765B2
(Deutsch Plug Number: DT06-3S)

Pin 1 Pin 2 Pin 3

Orange/White Orange/Black Blue/White

+12V to End of Bale Sensors Ground to End of Bale Sensors Signal

Integration Harness Plug on Baler Harness 006-765B2
(Plug: APTIV 12052848)

Pin A Pin B Pin C Pin D Pin E Pin F

Not Used Red Not Used Gray Orange Blue

—TBC Power —TBC Ground CAN Hi CAN Lo

Pump Connection on 700 Controller Harness
(16 AWG Two-Wire Plug)
Pin 1 Red Power to Pump Pin 2 Black Ground to Pump

1

3

2

4

1

2

3

A D

Pin 2

Pin 1

27

Star Wheel Sensors

1
3 2

7

9

15

16

10

14

4

8

11

13

5

12

6A or 6B

Ref Description

Part#

Qty

1 Star Wheel

006-4642US

1

2 Dust Seal Gasket

006-4642UG

1

3 Star Wheel Block

006-4642UB

1

(Avail. in 2024 Style Only)

4 3/8″ Wire Grommet

008-0821A

1

5 3/8″ Grommet Nut

008-0821B

1

6A Encoder Harness Plug 006-7307EM

1

(6 Pin)

6B Moisture Harness Plug 006-7307M

1

(2 Pin)

7 Spacer (only used in some 006-4642UBS

1

of the pre-2024 blocks)

8 Thrust Bearing Washer 006-4642K

2

9 Thrust Bearing

006-4642TB

1

Ref Description 10 Star Wheel Nut 11 Swivel Insert 12 Encoder Mount

Part#

Qty

006-4642U

1

006-4642B

1

006-4512P

1

13 Encoder

006-4512E

1

14 Electric Swivel

006-4642A

1

15 Star Wheel Block Gasket

006-4642UG

1

(Fits Pre-2024 Block Style)

15 Star Wheel Block Gasket

006-4642UG2 1

(Fits 2024 and Newer Blocks)

16 Block Cover

006-4642UC

1

(Fits Pre-2024 Block Style)

16 Block Cover

006-4642UC2 1

(Fits 2024 and Newer Block Style)

Complete Assembly w/Encoder

030-4642UE

Complete Assembly No Encoder

030-4642U

Twine Diverters and Moisture Harness

17

18

19

Ref Description 17 Twine Diverter- Left 18 Twine Diverter- Right 19 Moisture Harness

Part #

Qty

001-4645H

1

001-4644H

1

006-7307EM2 1

28

Control Box and Wiring Harnesses
1 2
2

3

5

4

Ref Description

Part#

Qty

1 Power Lead Baler 20′ 006-765B2

1

2 Power lead tractor

006-765IC

1

3 Key Switch Wire

006-765CPH 1

4 ISO Pump Module

006-7671LS 1

5 ISO Communication 006-6673

1

Module

Ref Description NP 120 Ohm Resistor NP Dust Plug Kit

End of Bale Sensor Kit

1

2

Part#

Qty

006-700R

1

006-765DP

1

Ref Description
1 End of Bale Sensor 2 End of Bale Ext.
Complete Assembly

Part #

Qty

006-7401

1

006-7401EXT

1

EOB-LS-STD

29

Notes
30

Harvest Tec Inc. Warranty and Liability Agreement
Harvest Tec, Inc. will repair or replace components that are found to be defective within 12 months from the date of manufacture. Under no circumstances does this warranty cover any components which in the opinion of Harvest Tec, Inc. have been subjected to negligent use, misuse, alteration, accident, or if repairs have been made with parts other than those manufactured and obtainable from Harvest Tec, Inc. Our obligation under this warranty is limited to repairing or replacing free of charge to the original purchaser any part that in our judgment shows evidence of defective or improper workmanship, provided the part is returned to Harvest Tec, Inc. within 30 days of the failure. If it is determined that a non-Harvest Tec branded hay preservative has been used inside the Harvest Tec applicator system where the failure occurred, then Harvest Tec reserves the right to deny the warranty request at their discretion. Parts must be returned through the selling dealer and distributor, transportation charges prepaid. This warranty shall not be interpreted to render Harvest Tec, Inc. liable for injury or damages of any kind, direct, consequential, or contingent, to persons or property. Furthermore, this warranty does not extend to loss of crop, losses caused by delays or any expense prospective profits or for any other reason. Harvest Tec, Inc. shall not be liable for any recovery greater in amount than the cost or repair of defects in workmanship. There are no warranties, either expressed or implied, of merchantability or fitness for particular purpose intended or fitness for any other reason. This warranty cannot guarantee that existing conditions beyond the control of Harvest Tec, Inc. will not affect our ability to obtain materials or manufacture necessary replacement parts. Harvest Tec, Inc. reserves the right to make design changes, improve design, or change specifications, at any time without any contingent obligation to purchasers of machines and parts previously sold. Revised 4/17
31

HARVEST TEC, INC. P.O. BOX 63
2821 HARVEY STREET HUDSON, WI 54016
PHONE: 715-386-9100 1-800-635-7468
FAX: 715-381-1792
32

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Harvest User Manuals

Related Manuals