HYUNDAI EM 7301 Stainless Steel Espresso Coffee Machine Instruction Manual

EM 7301

INSTRUCTION MANUAL
Espresso coffee maker

EM 7301 Stainless Steel Espresso Coffee Machine

INSTRUCTIONS FOR USE
Dear customer, thank you for purchasing our product. Keep these instructions including the  warranty, the receipt and, if possible, the box with the internal packing.

SAFETY WARNING

GENERAL PROVISIONS:
–  Before the first use, read the instructions for use carefully, look at the picture and stor the instructions for use for the future. Consider the instructions for use as a part of the  appliance and pass them on to any other user of the appliance.
–  Check whether the data on the type label correspond with the voltage in your socket.  The power cord plug has to be connected to the properly connected and grounded
socket according to the national standard.
– This appliance may not be used by children. Keep the appliance  and its cord out of the reach of children.
– The device may be used by persons with reduced physical or  mental abilities or lack of experience and knowledge only if they  are under supervision or they have been instructed about using  the appliance safely and understand the potential dangers.
– Children must not play with the appliance.
– Before replacing accessories or accessible parts that are moving  during operation, before assembly and disassembly, before you fill  the water tank, before cleaning and maintenance, before transfer,  if the appliance is left unsupervised, or if you finish using it, make  sure to switch OFF the appliance and unplug it from the mains by  pulling the plug from the socket!
– Before you remove any accessible parts, before maintenance and  handling, allow the appliance and any parts thereof to cool down.
– CAUTION – Do not use the appliance with a program, time switch  or any other part that turns the appliance on automatically as there  is a risk of fire if the appliance is not covered or placed properly.
– WARNING – Some parts of this product may become very hot and  cause burns.  During operation, the appliance produces hot water  and hot steam under pressure. Special attention must be paid to  the presence of children and handicapped people.
– Never immerse the appliance or its cord (or parts thereof) in water.
– WARNING, HOT STEAM – pay extra care when you are using the milk frother and do  not touch it until it has cooled down. Bear in mind that hot water might spurt out for a  short time during use. Do not touch the metal part of the nozzle during use; use only the  plastic part of the milk frother cover A3 to make adjustments.
– For hygienic reasons, clean the steam nozzle by flushing it after each use. After cooling,  remove the outer part (tube) and rinse it with lukewarm water.
– When the appliance is in operation, prevent pets, plants or insects to get in contact with it.
– Do not plug the fork of the supply cord into the power outlet and do not unplug the cord with wet hands or by pulling by the supply cord!
–  Prevent injuries when handling (e.g. by hot water, steam).
–  Never transfer the appliance when there is water in the tank! Water might leak into the  internal components.
–  Never leave the appliance unattended when it is connected to the mains and keep an  eye on it the whole time you are making your espresso!
–  When transferring the appliance, take it by the outer casing only.
– Leave a space of at least 15 cm from all sides of the appliance to ensure proper circulation of air.
–  Do not expose the appliance to temperatures under 4°C – if residual water froze in the  internal components, it could damage the appliance.
–  Use this appliance only for the purpose for which it was designed as specified in this  user‘s manual. Never use the appliance for any other purpose.
–  The producer is not responsible for damage caused by improper use of the appliance  (e.g. burning, scalding, fire) and its guarantee for the appliance does not apply  to situations when the safety warnings above are not complied with.

USE OF THE APPLIANCE:
– The appliance is intended for home use and similar (in shops,  offices and similar workplaces, in hotels, motels and other  residential environments, in facilities providing accommodation  with breakfast). It is not intended for commercial use!
–  If you are not going to use the appliance for a longer time, empty the water tank!  If you  do not brew coffee frequently, replace the water in the water tank regularly (preferably  every day) so as to keep it fresh at all times.
–  Use cold (lukewarm) clean water only!  Never use hot water or other liquids – they could  damage the appliance.
– Do not use the hot water feature longer than it takes to use up the capacity of one water tank.
– Use the appliance in the working position only at flat and stable places with no risk of turning over  and in sufficient distance from heat sources (e.g. heater, stove, cooker, oven, grill), flammable  objects (e.g. curtains, drapes, etc.) and wet surfaces (e.g. sinks, wash basins, etc.).
–  Do not place the appliance near objects or under objects which could get damaged by  steam, e.g. walls, kitchen cupboards, sideboards, paintings, or curtains. Leaking steam  could damage them.
– Do not use the appliance in an environment saturated with explosive or flammable steams.
– Before switching on the appliance ensure that the water level is between MIN and MAX marks.
POWER CORD:
– If the power cord of the appliance is corrupted, it has to be  replaced by the manufacturer, its service technician or a similarly  qualified person so as to prevent dangerous situations.
–  Never use the appliance if its power cord or plug is damaged,  if it does not work properly, if it fell down and was damaged  or if it fell to water. In this case take the appliance to a special  service to check its safety and proper function.
–  The power cable supplied with the appliance is designed solely for this appliance – never  use it for any other purposes. Also, this appliance may only be used with the power cable  included in the box. Never use any other cable type (e.g. for a different appliance).
–  Never put the power cord on hot surfaces or do not let it hang over the edge of a table  or a work top. Plugging or pulling the power cord e.g. by children can result in tilting over  or drawing the appliance down and serious injury!
–  The power cord must not be damaged with sharp or hot objects, open fire, it must not  be sunk into water or bent over sharp edges.

DESCRIPTION OF THE APPLIANCE

A – The machine body
A1 –  adjusting knob – steam and hot  water function
A2 – heating surface
A3 – steam nozzle and hot water outlet
A4 – protection cover
A5 – removable mouth
A6 – hot water outlet
A7 – power cord
A8 – power cable department
B – Control panel
B1 – button ON/OFF
B2 –  dish size setting button  (one cup / two cups)
B3 – button for one cup
B4 – button for two cups
B5 – steam and hot water button
B6 –  ground coffee quantity selector  switch
B7 – thermometer
C – Aluminium lever
C1 –  overpressure stainless-steel basket  for one cup
C2 –  overpressure stainless-steel basket  for two cups
C3 –  coffee tamping lever rest
C4 – folding dish holder
D – Water tank
D1 – hinged lid + handle
E – Drip tray
E1 – drip grille
E2 – control float
F – Coffee grinder
F1 – lever clamp
F2 –  ON button of coffee grinder
F3 – coffee bean container
F4 – lid
F5 – coffee grinder lock
F6 – grind size selector switch
F7 – sealing ring
G – Stamper
H – Milk jug
I – Brush
J – Slide-out accessories box

PREPARATION FOR USE

Before first use, remove any packaging and protective material (including any protective  film) from the appliance and accessories. Wash the water tank D with warm soap water,  rinse it with clean water and allow it to dry. Put it into the coffee machine again and press  it down as far as it goes.
Location
Place the coffee machine onto a flat and stable surface, near a socket.
Filling the tank with water
Remove the tank D from the coffee machine, open the lid D1 and fill it with water preferably  at room temperature (the water level must be between the MIN and MAX marks). Then put  the tank back in place.
Filling with coffee beans
Remove the lid F4 and fill the container F3 with coffee beans to the brim and then close the  container F3 with the lid F4.
Removing operational components
Looking at the camera that is used more often with the coffee machine (aluminium lever C,  water tank D, drip tray E, coffee bean container F3), proceed as shown in Fig. 1. Proceed  in reverse order to put the components back.

Rinsing the coffee maker
At the first start-up or if you have not used the coffee machine for more than 2 days, flush  it using the following procedure:

1. Fill tank D with water up to the MAX mark.
2. Place lever C and the stainless-steel bowl (C1/C2) on the coffee machine as shown in  Figure 2.
3. Connect the machine to the mains. Make sure that the rotary knob A1 is in the „ “ position.
4. The coffee machine must be switched on by pressing B1 button (all buttons will flash  and sound signal will be given).
5. Wait for the coffee machine to warm up sufficiently (illuminated buttons B3, B4 and B5 will be flashing during the heating phase, then all illuminated buttons will be lighting).
6. Place a suitable vessel of sufficient volume below the coffee outlet or use 2 bigger cups  which will be alternated in the course of rinsing, emptying the water in the cups.
7. Make several cups (without coffee) using buttons B3/B4). We recommend rinsing the  coffee machine 3 to 5 times using this procedure.

NOTICE
When rinsing, the coffee machine produces hot water.

USING THE APPLIANCE

Remarks
– After connection of the appliance with the electric mains, sound signal will be heard and illuminated buttons will flash several times.
– Heating up time of the coffee machine will be indicated by flashing illuminated buttons B3, B4 and B5. After warming up, the light on all buttons is continually on.
– The coffee brewing can be stopped at any time by pressing the corresponding B3/B4 button.
– When the coffee brewing is on, the A1 knob must be in the „ “, position, otherwise the coffee brewing function cannot be switched on.

COFFEE GRINDING

1. Make sure there are coffee beans in the F3 container.

2. Switch the coffee machine on by pressing the B1 button (make sure that the A1 knob is  in the „ “ position).

3. Use button B2 to select dish size for one cup (B2 is not lighting) or two cups (B2 is  lighting). When required, adjust the coffee quantity using selector B6 (depending on
   grind size and dish size).

4. Place dish (C1/C2) into lever C and insert the lever into holder F1 so that button F2 will  be pressed, thus starting the grinder. Now you can adjust the required grind size using  selector switch F6 (Fig. 3).

5. Wait until the grinding is completed. The grinding process can be stopped any time by  pressing B2.

Remark
When grinding coffee beans, set selector switch B6 to the initial position „ “ (Minimal).
Only when you can see, how much coffee has been ground, increase or adjust the coffee quantity using B6 as required.

Caution
When setting the grind size, make sure that the grinder is in operation (i.e. grinding)
– never adjust the grind size while the grinder is idle!

PREPARATION OF ESPRESSO

1. Set the steam knob A1 to the „ “ position.
2. Switch on the coffee machine by pressing button B1 and wait for it to warm up.
3. Grind the required amount of coffee according to the selected bowl (C1/C2)  (see procedure above). Trample properly coffee with the tamper.
4. Place the lever C on the coffee machine as shown in Fig. 2.
5. Place a suitable size cup / cups under the coffee spout.
6. Press B4 (for two cups – default 70 ml) or B3 (for one cup – default 40 ml).
7. Wait for the coffee to finish.

Cup preheat
– For an optimum coffee making process and better taste of your coffee, we recommend that you preheat your cup by filling it with hot water first (e.g. using the hot water
function). After the cup has been preheated, pour the water away.
– You can use the heating surface A2 to warm up the cup for your coffee.

MAKING CAPPUCCINO, CAFFÈ LATTE AND ESPRESSO MACCHIATO
The steam nozzle A3 is designed for making espresso beverages containing milk and milk  froth. For superior taste and quality of the beverage, use chilled fresh whole milk only.
Note
After using the steam nozzle, the coffee machine cools down automatically.

Recommended procedure

1. Pour milk into the milk jug H up to the end of the jug beak. The milk volume may be  approximately tripled.

2. Press B5 and wait until the steam jet is hot. During the heating phase, illuminated  button B5 will be flashing red. As soon as the steam nozzle is heated, the light signal of
   the button B5 lights up red.

3. Afterward place the milk jug with milk up to the level under the steam nozzle so that the  nozzle hole touched the milk surface. Rotate the regulator A1 into the „
   “ position  (steam jet A3 starts generating steam). Keep the end of the steam nozzle closely under  the surface of milk during all the time of whipping to obtain correct spiral rotation of  milk, which helps for ideal whipping. When whipping, watch for correct temperature of  the whipped milk, which is 55-65 °C.

4. Make sure to clean the milk frother immediately after use see chapter MAINTENANCE (we recommend basic quick cleaning, i.e. short-time repeated activation of the steam  nozzle and its cleaning by a wet cloth). Milk-caked frother is harder to clean.

5. Pour the frothed milk carefully over the coffee based on the espresso beverage you  have selected; you can use a teaspoon to do so.

Tip
You may determine correct temperature of whipped milk by touching by your palm the outer surface of the milk jug near its bottom. The milk jug is warm so that it is impossible to keep the palm on it.

COFFEE MACHINE COOLING DOWN (AFTER USING THE STEAM JET)
If selector A1 will be turned to „ “ after using the steam jet, buttons B3 and B4 will be  flashing quickly, thus informing that the temperature of the interior coffee machine system is too high for coffee preparation. Allow it to cool down by pressing B5 (hot water function)  twice and quickly. Flowing water will cause the interior system to cool down.

INDIVIDUAL SETTING OF THE AMOUNT OF COFFEE
The amount of coffee can be modified for 1 or 2 cups (using buttons B3 and B4). For both  buttons, water quantity can be adjusted, ranging from 30 to 150 ml. The procedure is as follows:

1. Switch on the coffee machine by pressing button B1 and wait for it to warm up.

2. Place the cup/cups of adequate volume below the coffee outlet.

3. Choose the relevant button (B3 or B4). Press and hold it until the required coffee  volume has been dispensed. Then release the button (sound signal will be generated).
   In this manner, the new coffee volume for B3 or B4 will be stored.

4. This amount will remain stored even if the coffee machine has been disconnected from  the mains.

Note
Press and hold buttons B3 and B5 simultaneously for approx. 3 seconds to delete pre-set amount of coffee. Illuminated buttons B3, B4 and B5 will flash several times, then the coffee machine will be switched off. Factory setting will be restored.

HOT WATER FUNCTION
Method 1:

1. Press B1 to turn on the coffee machine.
2. Wait for the coffee machine to warm up sufficiently (the light on all buttons is  permanently on).
3. Press B5 twice quickly.
4. Hot water will be flowing from outlet A6 for approx. 8 seconds.

Method 2:

1. Press B1 to turn on the coffee machine.
2. Wait for the coffee machine to warm up sufficiently (the light on all buttons is  permanently on).
3. Turn knob A1 to „ “.
4. Hot water will be flowing from outlet A3.
5. After completion of this function, turn selector A1 to „ “.

MAINTENANCE

Unplug the appliance from power supply by taking the fork of the power cord out of the socket (except for operations which require the coffee machine to remain switched on)! Clean the appliance only when it is cooled down! Don’t use a dish-washer nor rough and aggressive detergents (for example, sharp items, scrapers, diluent or other dissolution reagents)! Wipe the surface of the appliance and  its inlet with a damp cloth.
IMPORTANT
Regularly inspect and clean all parts to prevent mould on coffee residues!

Coffee grinder (F)
Depending on the frequency of use, clean the coffee grinder regularly (we recommend  at least once a month). Remove coffee bean container F3 and sealing ring F7 for easier  maintenance (Fig. 3). Clean the grinder and its parts in a dry way. Shake out, blow out  or use brush I to remove the coffee powder on the surface of the components. Cover F4 can be washed in water with added detergent (Allow to dry before using it again). Use the  reverse procedure to assemble the coffee grinder after maintenance.
Water tank (D)
We recommend that you clean the tank thoroughly and regularly (about once a week).  Use regular washing-up liquid and then rinse the tank with clean water. So as to prevent  build-up of scale deposits, we recommend that you also rinse the tank under running water  once a day.
Aluminium lever (C)
Remove coffee grounds from the stainless steel bowls (C1, C2) after each use. Rinse  the funnel thoroughly under running water. Wash the filters (C1, C2) in warm water with  detergent and then rinse with clean water. Wipe the plastic handle with a damp cloth. Then  let everything dry.
Drip tray (E)
Pour the drip tray as required. Wash parts E and E1 with a conventional dishwashing  detergent, rinse with clean water and allow to dry.
Steam nozzle and hot water outlet (A3)
The nozzle must be cleaned after each use. You can do so by activating it and immersing  it in a container of clean water and then wiping it with a dry tissue. Also, periodically clean  it by removing it by removing its A5 orifice. Where necessary, use a suitable tool (e.g.  needle)  to clean the orifice. Scale deposits in the outlet must be removed (refer to section Descaling).
Hot water outlet (A6)
Scale deposit in the outlet must be removed (refer to section Descaling).
Hot water outlet (A6)
If the drain is contaminated with limescale, it must be removed (see Removing limescale).
For more thorough cleaning you can remove the A7 orifice.
Descaling
We recommend that you remove scale at least once a month. Scale may be removed by  means of a solution of water with preparation destined for these purposes (for example,  ETA518000201). Always follow the manufacturer‘s instructions for the product, which are
usually on the packaging. The procedure is as follows:

1. Place approx. 1 litre of prepared cleaning solution in tank D (a proportion of detergent  and water – according to the manufacturer’s instruction).
2. Position lever C correctly.
3. Place a proper container under the coffee spout, steam nozzle and hot-water spout.
4. After heating up of the coffee machine by pressing B3/B4, make several operation  cycles with the cleaning solution (at least 5-10 cycles are recommended).
5. Then rinse both hot water outlets (A3 and A6) with the cleaning solution, using both hot  water methods (refer to section HOT WATER FUNCTION).
6. After thorough rinsing of the coffee machine with the cleaning solution, empty and rinse  water tank D. Then fill approx. 1 l pure water into tank D and repeat the procedure  again to remove all remainders of the cleaning solution from the interior system.

Expert service must do the large maintenance or to intervene into inside parts of the appliance! Non-observance of the instructions of the manufacturer cancels the right for guarantee repair! If you are unable to fix the problem, or if you need any further  information about the appliance or service centres, please contact your distributor.

TECHNICAL DATA

Input in off mode is <0,50 W
The manufacturer reserves the right to change the technical specifications and accessories for the respective models.

LEGISLATIVE & ECOLOGY

WARNING: DO NOT USE THIS PRODUCT NEAR WATER, IN WET AREAS TO  AVOID FIRE OR INJURY OF ELECTRIC CURRENT. ALWAYS TURN OFF THE  PRODUCT WHEN YOU DON’T USE IT OR BEFORE A REVISION. THERE  AREN’T ANY PARTS IN THIS APPLIANCE WHICH ARE REPARABLE BY  CONSUMER. ALWAYS APPEAL TO A QUALIFIED AUTHORIZED SERVICE. THE PRODUCT IS UNDER A DANGEROUS TENTION.
Disposal of old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems).
This symbol on the product or on its packaging indicates that this product (or battery/accumulator) shall not be treated as household waste. Instead it shall be  handed over to the applicable collection point for the recycling of electrical and  electronic equipment. By ensuring this product is disposed of correctly, you will  help prevent potential negative consequences for the environment and human  health, which could otherwise be caused by inappropriate waste handling of this  product. The recycling of materials will help to conserve natural resources. For more  detailed information about recycling of this product, please contact your local Civic Office,  your household waste disposal service or the shop where you purchased the product.

WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING OR IN THE INSTRUCTIONS MANUAL:
HOUSEHOLD USE ONLY; DO NOT IMMERSE IN WATER OR OTHER LIQUIDS; TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.
The symbol indicates a WARNING.
WARNING:  HOT SURFACE

Licensed by HYUNDAI Corporation Holdings, Korea
Imported by ETA a.s., náměstí Práce 2523, 760 01 Zlín, CZ

References

• AEG Hausgeräte | Setzen Sie auf Qualität | AEG
• ETA - tady je doma
• ETA - tu je doma
• Hyundai Electronics– Hyundai CZ
• Hyundai Electronics– Hyundai SK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>