BEA LZR-FLATSCAN 3D SW Door Control Wiring Matrix Owner’s Manual

: September 8, 2024
: BEA

Table of Contents

BEA LZR-FLATSCAN 3D SW Door Control Wiring Matrix
Product Usage Instructions
Control Harness: 20.5433
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEA LZR-FLATSCAN 3D SW Door Control Wiring Matrix

Specifications

Model: LZR-FLATSCAN SW / LZR-FLATSCAN 3D SW
Manufacturer: BEA, Inc.
Control Harness: 20.5433
Power Input: 24V DC

Product Usage Instructions

Installation Requirements
Before starting the installation process, ensure that:

Installation and service technicians are certified appropriately.
Risk assessments are conducted after each installation.
Compliance with local, national, and international regulations is verified.
All necessary signage and warning labels are in place.

Wiring Instructions
Refer to the provided wiring matrix for connecting the control harness to compatible door/gate systems.

Power Connection
Connect the power input to a 24V DC power source following the specified wiring connections.

Additional Information
For detailed instructions on specific door/gate systems, refer to the BEA product User’s Guide and OEM manual.

FAQ

Q: What certifications are recommended for installation technicians?
A: BEA, Inc. recommends AAADM certification for pedestrian doors, IDA certification for doors/gates, and factory training for the specific door/gate system.
Q: What should be verified before starting the installation process?
A: Verify that all appropriate industry signage, warning labels, and placards are in place, and that technicians are certified and compliant with regulations.

BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS
BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device; therefore, BEA, Inc. does not guarantee any use of the sensor/device outside of its intended purpose. BEA, Inc. strongly recommends that installation and service technicians be AAADM-certified for pedestrian doors, IDA-certified for doors/gates, and factory-trained for the type of door/gate system. Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor/device system performance is compliant with local, national, and international regulations, codes, and standards.

Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer’s recommendations and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must be performed during each service call – examples of these safety inspections can be found on an AAADM safety information label (e.g. ANSI/DASMA 102, ANSI/DASMA 107, UL294, UL325, and International Building Code). Verify that all appropriate industry signage, warning labels, and placards are in place.

Control Harness: 20.5433

Control Harness: 20.5433| __| __| __|
| __| __**W| | | |
---|---|---|---|---|---|---|---|---|---|---
POWER 1| O1: N.O.| O1: N.C.| O1: COM| O2: REACTIVATION 2| O2: ACT (COM)| O3: VPB 3| MONITORING 4
Besam ETIK 5| 30.5558| | 15/17| 16/18| Logic Module| 12| 13| Not supported.
Besam MP/CUP| 30.5558| 5| | 4| Logic Module| 4| 3| Not supported.
Besam PowerSwing/EXB| 30.5558| | TB4-29| TB4-26| Logic Module| TB3-20| TB3-21| Not supported.
Besam SM| 30.5558| TB1-7| | 3| Logic Module| 3| 1| Not supported.
Assa Abloy SW 100/200, DITEC HA9 6| 24V+| GND| | EXU-SA 3| EXU-SA1| EXU-SA 1 and 2 (N.C.)| CU-ESD 1| CU-ESD 2| Refer to BEA product User’s Guide and OEM manual.
CONDOR| 30.5558| DMS O| | COMMON N| V and W| COM 16| ACTIVATE 17| Not supported.
DCU DC700
Access Auto. ES500 Quad Systems ES500| 30.5558| CN6 GREEN| | CN6 BLACK| AUX CN7 (AF = 2)| CN2 #3| CN2 #2| Not supported.
Detex BS1000S/UDC100| 30.5558| 5| | 1| J2-3 and 1| 1| 2| Not supported.
Dor-O-Matic| 30.5558| PURPLE| | GRAY| Logic Module| GRAY| YELLOW| Not supported.
Dorma 400/700| 30.5558| SWING| | GND| APPR and GND| GND| TRIGGER| Not supported.
Dorma ED 100/250 7| 1| 3| | 15| 3| 11 (N.C.)| 3| 42| Refer to BEA product User’s Guide and OEM manual.
Gyrotech/Nabco Magnum| 30.5558| 3 VIOLET| | 5 RED| Logic Module| 5 RED| 6 BLACK| Not supported.
Gyrotech/Nabco Opus| 30.5558| 5| | 2| 2 and 4| 2| 3| 1 and 7
Gyrotech/Nabco U19| 30.5558| WHITE 6B| | RED 7| Logic Module| RED 7| 61/62| Not supported.
Gyrotech 300/400 8| 30.5558| WHITE| | RED| Logic Module| RED| BLACK| Not supported.
Horton 4160-3 9| 30.5558| DAUGHTER BOARD| | DAUGHTER BOARD| Logic Module| WHITE| BLACK| Not supported.
Horton 4190 10| 30.5558| 10| | 3| 11 and 2| 3| 2| Not supported.
Horton 5190| +24 VDC| 0 V| CN16 ORANGE (10)| | CN16 YELLOW (9)| CN16 GREEN (8)| CN16 BROWN (7)| CN20: 2 = interior, 3 = exterior CN7 COM| __ CN16 PURPLE (13), BLUE (14)
Hunter HA, DITEC HA8| 30.5558| SAFE 2| | RTN| ACT 2 and return| RTN| ACT| Not supported.
Keane-Monroe K| 30.5558| YELLOW| | WHITE| Logic Module| WHITE| GREEN| Not supported.
LCN Digital / Senior Swing| 30.5558| P2 GREEN| | P2 WHITE| P3 white and green| P6 GRAY| P6 YELLOW| Not supported.
Record 6000/8000 11| 4| 6| | 10| 11| 11 and 12 (N.C.)| 1| 2| Refer to BEA product User’s Guide and OEM manual.
Stanley “L” 12| 30.5558| BLUE| | YELLOW| Logic Module| YELLOW| ORANGE| Not supported.
Stanley MP| 30.5558| 7| | 8| Logic Module| 8| 2| Not supported.
Stanley MC 521 13| 30.5558| TB3-4| | TB3-3| TB5 3 and 4| TB4-3| TB4-4| Refer to BEA product User’s Guide and OEM manual.
Stanley MC 521 Pro and IQ 13| TB4-5| TB4-6| TB3-4| | TB3-3| TB5 3 and 4| TB4-3| TB4-4| Refer to BEA product User’s Guide and OEM manual.
Tucker| 30.5558| | J4-14| J4-8 jumped to 12 & 13| N.C. contact between J4 13 and COM| J4-8 jumped to 12 & 13| J4-10| Not supported.
Tormax 1301Motion| 30.5558| SAFETY A #2| | SAFETY A #1| A6| A5| INPUT C #2| Refer to BEA product User’s Guide and OEM manual.
Tormax TDA| 30.5558| 7| | 8| C4 and C8| 8| 2| Not supported.
Tormax TTX II**| 30.5558| | | 14| 17 and 18| 4| 5| Not supported.
Note 1| If only VAC power is available, a 12V transformer paired with a rectifier must be used. Do not use a 24V transformer and rectifier as this will cause damage to the product.
---|---
Note 2| LE21 function or BR3-X programmed to function 22
Note 3| FS3D only.
Note 4| Monitoring consists of two purple and two blue wires. If monitoring is not used, cap off unused purple and blue wires. Wire as follows:| Door Type| System Harness| Control Monitoring
---|---|---
Single| 1 blue + 1 purple| 1st leg
1 blue + 1 purple| 2nd leg
Pair / Dual Egress| 1 blue + 1 purple| 1st leg
1 blue + 1 purple| 2nd leg
Pair / Dual Egress
(independent controls)| 2 blues| 1st control
2 purples| 2nd control

Effective November 11, 2017: Monitoring is required for ANSI 156.10 compliance.

Note 5
(BESAM ETIK)| Jump 17+18, if not used.
Note 6
(BESAM SW 100/200)| Set EXU-SA jumper to “Door open/closed” indication. Jump 1+2 on EXU-SA board.
Blanking Potentiometer must be set fully counterclockwise. Auxiliary switch may be used for home switch.
Note 7
(DORMA ED 100/250)| Jump 11+3 on ontrol. Use ON/OFF/H.O. jumper. Control switches must be used. Make certain Home Switch Control Function “Sr” is set to 1.
Note 8
(GYROTECH 300/400)| Set control to “swing-safe.”
Note 9
(HORTON 4160-3)| Must have daughter board.
Note 10
(HORTON 4190)| PNP harness p/n: 20.5322
Note 11
(RECORD 6000/8000)| Jump 11+12 and 14+15.
Note 12
(STANLEY “L”)| The older Stanley, all metal (silver), “L” shape control does not have stall. A control with stall must be used.
Note 13
(STANLEY MC521 / MC521 PRO)| Jump TB2 2+3 (if not using factory On/Off/Hold Switch).