SYLVI Bella Mesh Strap Watches Instruction Manual
- September 7, 2024
- SYLVI
Table of Contents
SYLVI Bella Mesh Strap Watches
Specifications
- Watch Dial Diameter: 19mm
- Watch Case Height: 28mm, Diameter: 24mm, Thickness: 8mm
- Strap:
- Leather – Width: 10mm, Thickness: 3mm
- Stainless Steel – Width: 12mm, Thickness: 4mm
- Mesh – Width: 10mm, Thickness: 2mm
- Water Resistant: 3 ATM
Product Usage Instructions
- Gently pull the crown out to position B.
- Turn it in either direction until you reach the correct time.
- After setting the correct time, push the crown back to position A (Normal).
- The watch uses an LR621 battery cell. Follow the instructions provided for replacing the battery.
- Instructions on how to adjust and wear the different types of straps provided with the watch:
- Understand the water-resistant rating and recommended usage guidelines to prevent damage to the watch. Follow the chart for appropriate water-related exposure.
Brief Introduction
Function Instruction
Watch Dial
- Diameter: 19mm
Watch Case
- Hight: 28mm
- Diameter: 24mm
- Thickness: 8mm
Water Resistant
- 3 ATM
Strap
Leather
- Width: 10mm
- Thickness: 3mm
Stainless Steel
- Width: 12mm
- Thickness: 4mm
Mesh
- Width : 10mm
- Thickness: 2mm
Operation Instructions
How to Set Time
- Gently pull the crown out to position B.
- Turn it in either direction until you reach the correct time.
- After setting the correct time, push the crown back to position A (Normal).
Battery Instructions
- A LR621 battery cell for the chronograph watch
Strap Instructions
Stainless steel strap
- The strap with 10mm width & 16cm Length.
Mesh strap
- The strap with 10mm width & 18cm Length.
Leather strap
- The strap with 10mm width & 17cm Length.
Water Resistant
For information about the water-resistant rating of Sports, Casual, Chronograph, and Slim watches please refer.
- The water-resistant rating provides guidelines for appropriate water-related exposure to avoid damage to internal watch components.
- Please see the chart for recommended usage guidelines.
To ensure water does not enter the watch and cause damage to it, please follow the instructions listed below:
- Do not adjust the crown while the timepiece is in contact with water.
- Ensure the crown is in the closed position before contact with water. For timepieces with screw-down crowns, ensure the crown is completely tightened before contact with water.
- For timepieces with pusher-enabled functionality, do not engage the function underwater.
- Exposure to the extreme atmosphere is not recommended (i.e. hot water, saunas, or steam rooms).
- Avoid exposure to water moving with force (i.e. water running from a faucet, ocean waves, or waterfalls).
- Avoid long exposure to saltwater. After contact with salt water, rinse the watch under tap water
- If rated 5ATM or higher and wipe dry with a soft cloth.
Warranty Instructions
Your watch is warranted for six (6) months from the original date of purchase under the terms and conditions of the warranty. The warranty covers manufacturing defects, i.e. the watch movement, hands, and dial only. The covered components will be repaired or the watch will be replaced free of component and labor charges if it proves to be defective in material or workmanship under normal use.
- In case of replacement, we cannot guarantee that you will receive the same model watch.
- If your model is not available, a watch of equal value and similar style will be provided.
This warranty does not cover
- Any defect in materials and workmanship of battery, case, crystal, button, crown, strap, or bracelet; including plating on the case and/or bracelet.
- Damage resulting from improper handling, lack of care, accidents, normal wear and tear or aging.
- Water damage if care instructions for the product’s water resistance levels (as per the product specification) were not followed.
- Products that are not purchased from an authorized retailer.
- This warranty is void if the watch has been damaged by accident, negligence of persons other than authorized sales or service agents, unauthorized service, or other factors not due to defects in materials and workmanship. This warranty is void if the serial number or product date codes or other tracking marks have been removed, altered, or obliterated.
Get Additional Warranty
- https://sylvi.in/warranty-registration Click Here to Open
How to Claim Warranty?
Step 1
- Contact customer care and report your problem. An RMA ID will be generated (Without RMA ID, warranty cannot be claimed
Step 2
The product will have to be sent to the service center including the following information.
- RMA ID – Given by customer care executive
- Name
- Full address
- Daytime contact mobile number
- Email address
- Where your item was purchased from
- Model reference of the item (Found on the back of your watch)
- Full description of the work required
- A copy of your proof of purchase
How to Reach Us?
- For any service-related inquiries and feedback, call our number +919687660234 Monday to Saturday, 10.00 am to 6.00 pm.
- (closed on National and Festival holidays).
- If you are unhappy for any reason, please mail us at customercare@sylvi.in.
- We promise to reply by the next working day. www.sylvi.in
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>