MEMPHIS AUDIO GEN65FE Polaris General OEM Direct Fit Front Speaker Enclosures Instruction Manual

MEMPHIS AUDIO DIRECT FIT OEM POWERSPORTS SPEAKERS

Memphis Audio direct fit OEM audio systems include everything you need to make your machine the loudest on the trails. These kits are designed to fit directly into your vehicle with zero custom fabrication required. Lightweight durable polypropylene speaker enclosures are tuned for maximum output and feature RGB LED lighting which illuminates the speaker cone, Memphis badge and provides down lighting making your machine stand out from the crowd. All the components used in this kit are marine grade IP66 rated and designed to withstand water and the elements allowing you to bring the party wherever the trails take you.

BEFORE YOU BEGIN!

If you are uncertain about any aspect of this installation processb check out the complete walk-through video in the link below:
WWW.MEMPHISCARAUDIO.COM/INSTALLATION-CENTER

Memphis Audio recommends all installations be completed by a certified authorized Memphis Audio dealer.

SPEAKER POD INSTALLATION

WARNING:

These instructions are designed to be used on 2016 and newer Polaris General Models. These pods are designed specifically to work with these types of machines. If you have a different year or model machine, check with your authorized Memphis Audio dealer or contact Memphis Audio customer service at 800-489-2300 prior to attempting installation. These kits are not designed to be used with any other model or year vehicle. Attempting to install these speakers on any other vehicle may result in permanent damage to your vehicle.

PASSENGER SIDE SPEAKER INSTALLATION

1. STEP 1:
   Cut out the inside template (driver/passenger) along the cut line. Position the template on the kick panel above the foot rest making sure to line up the arrows on the template to the curves of the vehicle panel as shown above. Secure the template to the panel with tape to prevent it from moving. Scribe the 3 points above. These points will correspond to the threaded inserts on the back of the appropriate enclosure.
   

2. STEP 2:
   Remove the template, locate the 3 scribe marks and use a 1/4” drill bit to drill holes in each marked location.
   

3. STEP 3:
   Place the pod on kick panel mounting location. The holes should line up with the threaded inserts in the enclosure. You will then use the provided M6 screws and washers to loosely tighten the pods in place through the drilled holes. Once all three screws are loosely threaded, then tighten all three by hand until snug.
   
   DRIVER’S SIDE SPEAKER INSTALLATION

4. STEP 4
   Follow the same steps as above using the “Driver’s Side” template.

EXAMPLE OF PROPERLY INSTALLED PODS

• Driver’s Side
  

• Completed Installation
  

• Passenger’s Side
  

EXPAND YOUR SYSTEM WITH THESE ADDITIONAL PRODUCTS DESIGNED FOR YOUR MACHINE

MXAMCAPP – APP CONTROLLED SOURCE UNIT

Need to control your audio system but don’t want to alter your dash? The MXAMCAPP App controlled source unit gives you all the features and control of a traditional head unit directly from your phone or Bluetooth device. The black box hideaway unit is a fully functional Bluetooth streaming, AM/FM Radio with all the features of a traditional radio in a small IP66 rated marine grade package. To learn more visit www.memphiscaraudio.com or call us at 800-489-2300.

MXAMCAPP – Headless Unit

• 5 Source Options: AUX/BT/AM/FM/WB
• USB charging
• 50W x 4 built-in amplifier
• RGB LED control output
• Front/Rear/Subwoofer RCA output
• 5 Volt pre-amp output
• Conformal coated PCB IP66 Rated
• Wired remote fits standard rocker cutouts
• Wired remote buttons illuminate

REAR SPEAKERS

Add to your system with these rear powersports pods. The kits include all the hardware needed to mount directly to your machine. These high performance speakers are equipped with RGB LED lighting and are IP66  rated to withstand water and the elements. Contact yourlocal Memphis Audio Dealer or contact us at 800.489.2300 to determine if you will need a bracket kit for your specific machine to mount these speakers.

DRILL HOLE

MARK THIS LOCATION ON THE MACHINE ITSELF PRIOR TO DRILLING

BEFORE YOU DRILL

Check your template prior to drilling holes. Be certain the fold line and the cut line correspond to the angles and features of the panel. Do not drill holes without double checking for accuracy. Mark the panel itself prior to drilling. Do not attempt to drill directly through this template. The template may move or become damaged by the drill and you will not achieve an accurate hole pattern. Scribe the markings directly onto the panel itself prior to drilling. If you do not feel comfortable drilling into your machines panels, stop now and see your local authorized Memphis Audio dealer. Memphis is not responsible for any damage that may occur to your machine during this installation process.

CONTACT US

MEMPHISAUDIO

@MemphisCarAudioUSA
@MemphisCarAudio
800.489.2300
www.memphiscaraudio.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>