GABOR FPS-G SWIVEL TV Floor Stand with Glass Base User Manual
- September 6, 2024
- GABOR
Table of Contents
- FPS-G SWIVEL TV Floor Stand with Glass Base
- Product Specifications
- Safety Warnings
- Parts List
- Attaching the Feet
- Assembling the Riser and Base
- Attaching the Display Mount
- Attaching the Media Tray
- Attaching the Display Brackets
- Hanging the Display on the Mount
- Securing the Display Cable Management
- Adjusting the Angle
- Q: What should I do if I encounter issues during assembly?
- Q: Can I use this stand for a TV larger than 70 inches?
FPS-G SWIVEL TV Floor Stand with Glass Base
“`html
Product Specifications
-
Product Name: FPS-G / SWIVEL TV FLOOR STAND WITH GLASS
BASE -
Compatible Display Size: 37 to 70 inches
-
Manufacturer: Gabor
Safety Warnings
Follow all safety precautions mentioned in the user manual to
prevent any accidents or damage.
Parts List
Required tool: Phillips screwdriver
Attaching the Feet
1. Peel off the protective paper from the pads.
2. Press the pads into place on the bottom of the base.
3. Position each pad approximately 1-1.5 inches (2.5-3.8 mm)
from each edge.
Assembling the Riser and Base
Follow the instructions provided in the user manual to assemble
the riser and base correctly.
Attaching the Display Mount
Refer to the user manual to attach the display mount securely to
the stand.
Attaching the Media Tray
Follow the user manual instructions to attach the media tray to
the stand.
Attaching the Display Brackets
1. Ensure the arrow on the bracket faces up toward the top of
your TV.
2. Select appropriate-size screws and washers for VESA
standards.
3. Hand-thread the screw to determine the correct diameter.
4. Install brackets directly or use spacers based on your TV’s
back type.
Hanging the Display on the Mount
It’s recommended to have two people for this step.
Determine which bracket hooks to use based on TV size and
preferred screen height.
Securing the Display Cable Management
Secure and manage display cables properly to avoid tangling or
accidents.
Adjusting the Angle
The mounting arm swivels 35 degrees in either direction for
adjusting the viewing angle.
ONE-YEAR LIMITED WARRANTY
FAQ
Q: What should I do if I encounter issues during assembly?
A: Refer to the troubleshooting section in the user manual or
contact customer support for assistance.
Q: Can I use this stand for a TV larger than 70 inches?
A: The stand is designed for displays between 37 to 70 inches;
using it for larger TVs may not provide adequate support.
“`
FPS-G / SWIVEL
TV FLOOR STAND WITH GLASS BASE
for 37 to 70 in. Displays
User Manual
Thank you for choosing Gabor.
The Gabor FPS-G is a floor-standing TV mount that accommodates flat-panel
screen sizes that measure from 37 to 70 inches, and weigh up to 88 pounds.
Swivel the screen ±35° and hide the cables for the ideal viewing angle and a
clean, organized look in any room. The glass base provides a counterbalance
and elevates the stand’s design for an upscale aesthetic.
Product Specifications
Compatible flat-panel display sizes: 37 to 70 in. (94 to 177.8 cm) Height:
57.4 in. (145.8 cm) Max weight capacity: 88.2 lb. (40 kg) Weight: 33.7 lb.
(15.3 kg) VESA mounting patterns: 200 × 200, 300 × 200, 300 × 300, 400 × 200,
400 × 300, 400 × 400, 600 × 400 mm Material: Plastic, Steel, Tempered Glass
A/V shelf size: 11.8 × 10.4 in. (30 × 26 cm) Base dimensions: 25.6 × 15.7 ×
0.4 in. (65 × 40 × 1 cm)
2
Safety Warnings
· When installing this product, be sure to refer to the mounting instructions
detailed in this manual; failure to follow the mounting instructions may void
the product warranty.
· It is strongly recommended that this product be installed by a qualified
professional or installation contractor; Gabor takes no responsibility for any
product damage or personal injury resulting from mishandling, incorrect
mounting, faulty assembly, or improper use of this product.
· Do not use this product for any flat-panel screen device other than what it
is intended for; the exact specifications, size parameters, and weight limits
are found both on the product box and in the instruction manual.
· It is recommended that at least two people perform the installation process
to prevent injury from mishandling or dropping the product or flat-panel
display; proper safety gear and tools must be used at all times when
installing this product.
· Do not assemble or use this product on structures that may be affected by
vibrations or noticeable impacts; do not assemble or use near a heater,
fireplace, or any other source of direct heat energy.
· This product may contain small parts which can pose a choking hazard; keep
out of reach of children and pets.
· Excessive exposure to liquids may damage the finish of this product; when
cleaning this product, use only a mild detergent solution and quickly wipe dry
with a soft cloth.
· If you have safety concerns about installing this product, contact a
qualified professional or installation contractor.
· If this product is missing hardware or there are defective parts, visit
www.madebygabor.com or call Customer Service at
212-594-2353.
· All images are for illustrative purposes only.
3
Parts List
Required tool: Phillips screwdriver
4
Attaching the Feet
Peel off the protective paper from the pads, and press them into place on the
bottom of the base. Position each pad so it’s approximately 1-1.5 inches
(2.5-3.8 mm) from each edge.
Assembling the Riser and Base
5
Attaching the Display Mount
6
Attaching the Media Tray
7
Attaching the Display Brackets
Make sure the arrow on the bracket is facing up toward the top of your TV. A
variety of screws are included for different VESA standards on the backs of
most displays. Select the appropriate-size screws and washers. Hand-thread the
screw to determine the correct diameter.
If the screw is too short, it may not hold the display. If it’s too long, it
may damage the display.
If Your TV Has a Flat Back: Install the brackets directly to your TV, using
only the screws and washers provided. If the screw is too long, install the
spacers between the bracket and your display. You can combine spacers to best
fit your display. Then fasten with the screws and washers until secure.
If your display has recessed mounting or a curved back: Install the spacers
between the bracket and your display. You can combine spacers to best fit your
display. Then fasten with the screws and washers until secure.
8
Hanging the Display on the Mount
It’s highly recommended to perform this step with two people.
Determining which bracket hooks to use to secure your TV to the stand depends
on the size of your TV and preferred height of the screen.
9
Securing the Display Cable Management
10
Adjusting the Angle
The mounting arm swivels 35 degrees in either direction. Turn the screen for
the preferred viewing angle.
11
ONE-YEAR LIMITED WARRANTY
This Gabor product is warranted to the original purchaser to be free from
defects in materials and workmanship under normal consumer use for a period of
one (1) year from the original purchase date or thirty (30) days after
replacement, whichever occurs later. The warranty provider’s responsibility
with respect to this limited warranty shall be limited solely to repair or
replacement, at the provider’s discretion, of any product that fails during
normal use of this product in its intended manner and in its intended
environment. Inoperability of the product or part(s) shall be determined by
the warranty provider. If the product has been discontinued, the warranty
provider reserves the right to replace it with a model of equivalent quality
and function. This warranty does not cover damage or defect caused by misuse,
neglect, accident, alteration, abuse, improper installation or maintenance.
EXCEPT AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS
WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This
warranty provides you with specific legal rights, and you may also have
additional rights that vary from state to state. To obtain warranty coverage,
contact the Gabor Customer Service Department to obtain a return merchandise
authorization (“RMA”) number, and return the defective product to Gabor along
with the RMA number and proof of purchase. Shipment of the defective product
is at the purchaser’s own risk and expense. For more information or to arrange
service, visit www.madebygabor.com or call Customer Service at
212-594-2353. Product warranty is
provided by the Gradus Group. www.gradusgroup.com Gabor is a registered
trademark of the Gradus Group. © 2024 Gradus Group LLC. All Rights Reserved.
GG3
12
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>