GABOR DMH-10B LEVITOUCH Single ARM Heavy Duty Desktop Monitor Mount User Manual
- July 5, 2024
- GABOR
Table of Contents
- GABOR DMH-10B LEVITOUCH Single ARM Heavy Duty Desktop Monitor Mount
- Product Usage Instructions:
- Product Specifications
- Clamp Installation
- Grommet Installation
- Attaching the Arms
- Attaching the Monitor Mount
- Attaching the VESA Plate to a Monitor
- Attaching the VESA Plate to a Monitor (cont.)
- Attaching the Monitor
- Balancing the Arm M
- Adjusting Arm Swivel
- Adjusting the Tilt Angle
- Adjusting the Monitor Orientation
- Organizing Cables
- FAQ
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
GABOR DMH-10B LEVITOUCH Single ARM Heavy Duty Desktop Monitor Mount
Product Specifications:
- Monitor Display Size: 17 to 57 in. (43.2 to 144.8 cm)
- Maximum Load: Curved – 48.4 lb. (22 kg), Flat – 59.4 lb. (27 kg)
- Maximum Desktop Thickness: Clamp – 1.8 in. (45 mm), Grommet – 1.6 in. (40 mm)
- Maximum Reach: 23 in. (58.5 cm)
- Arm Height Adjustment: 12.8 to 25.75 in. (32.5 to 65.4 cm)
- Weight (without monitor): 10.8 lb. (4.9 kg)
- Package Weight: 13.1 lb. (5.9 kg)
Product Usage Instructions:
Clamp Installation:
For desks or tabletops 0.4 to 1.8 in. (10 to 45 mm) thick
- Use a hex key to loosen the clamp screw and widen the clamp to the thickness of the mounting surface.
- Slide the clamp onto the edge of the surface and tighten the clamp until secure.
Grommet Installation
For desks or tabletops 0.4 inch to 1.6 in. (10 to 40 mm) thick
-
Use a hex key to remove the clamp screw and clamp from the base.
-
Insert the carriage bolt through the grommet hole and the
predrilled hole in the surface. Screw the flange onto the end ofthe bolt. -
Tighten the flange with a hex key until the base is securely attached to the surface.
Attaching the Arms
- Place the base arm into the base socket and tighten the base set screw.
- Fit the monitor arm into the base arm’s receiver and tighten the set screw.
Attaching the Monitor Mount
- Unscrew the VESA thumbscrews, remove the VESA plate, and attach the monitor mount to the arm.
- Tighten the set screw to secure the monitor mount.
Attaching the VESA Plate to a Monitor
- Select the right VESA mounting hardware for your display based on VESA patterns.
GABOR DMH-10B LEVITOUCH Single ARM Heavy Duty Desktop Monitor Mount
The Gabor Levitouch desktop monitor mount is a heavy-duty mount that’s
designed to hold a 57-inch flat or curved monitor and deliver optimum viewing
angles whether you’re sitting or standing. It clamps to desks and tabletops
and will preserve desk space while it securely holds oversized monitors when
you’re gaming, video editing, or watching a movie. The articulating arm has
adjustable gas-spring tension that ensures monitor stability and glides into
place when changing the monitor’s height, tilt, and orientation
Safety Warnings
- Please read and follow the instructions, and keep this manual in a safe place.
- When installing this product, be sure to refer to the mounting instructions detailed in this manual; failure to abide by the mounting instructions may void the product’s warranty.
- Do not use this product for uses other than those intended; the exact specification, size parameters, and weight limits are found both on the product box and in the instruction manual.
- Gabor takes no responsibility for any product damage or personal injury resulting from mishandling, incorrect mounting, faulty assembly, or improper use of this product.
- This product may contain small parts that can pose a choking hazard; and keep out of reach of children and pets.
- Make sure this product is intact and there are no missing parts.
- Mounting surfaces should be sturdy and flat. Do not install this product on a weak, uneven surface.
- Do not mount the device on structures that may be affected by vibrations or noticeable impacts; do not install it near a heater, fireplace, or any other source of direct heat energy.
- Clean this product with only a soft, dry cloth.
- All images are for illustrative purposes only.
Product Specifications
Monitor Display Size
- 17 to 57 in. (43.2 to 144.8 cm)
Maximum Load
- Curved: 48.4 lb. (22 kg)
- Flat: 59.4 lb. (27 kg)
Maximum Desktop Thickness
- Clamp: 1.8 in. (45 mm)
- Grommet: 1.6 in. (40 mm)
Maximum Reach
- 23 in. (58.5 cm)
VESA Standards
- 75 × 75 mm
- 100 × 100 mm
- 200 × 100 mm
- 200 × 200 mm
- Monitor Tilt
- +60° to -20°
Monitor Arm Swivel
- ±90°
Base Arm Pivot
- 360°
Arm Height Adjustment
- 12.8 to 25.75 in. (32.5 to 65.4 cm)
- Weight (without monitor)
- 10.8 lb. (4.9 kg)
Package Weight
- 13.1 lb. (5.9 kg)
Package Dimensions
- 17.2 × 9.8 × 5 in. (43.8 × 25 × 12.7 cm)
Overview
Overview
Clamp Installation
For desks or tabletops 0.4 to 1.8 in. (10 to 45 mm) thick
- Use hex key (M) to loosen the clamp screw, and widen the clamp to the thickness of the mounting surface.
- Slide the clamp onto the edge of the surface, and tighten the clamp until it’s secure.
Important
Make sure the back edge of the clamp is flush against the mounting surface
Grommet Installation
For desks or tabletops 0.4 inch to 1.6 in. (10 to 40 mm) thick
Important
Predrilled holes should be between 0.4 to 2.4 inches (Ø10-60mm)in diameter.
- Use the ex key (M) to remove the clamp screw and clamp from the base.
- Insert the carriage bolt (G) through the grommet hole and the predrilled hole in the surface. Screw the flange (E) onto the end of the bolt. Make sure the flat edge of the flange faces up.
- Tighten the flange with the hex key (M) until the base is securely attached to the surface.
Attaching the Arms
The base arm has two equally sized sockets and the slip-off cable guide. The top arm has a screw-on cable guide.
-
Place the base arm (B) into the base socket, and tighten the base setscrew with the slotted screwdriver end of hex key (L).
Note
The base arm’s receiver should fit snugly onto the base. If it wobbles on the base, it’s upside down. Use the receiver on the other end of the base arm -
Fit the monitor arm (A) into the base arm’s receiver, and tighten the setscrew with the slotted screwdriver endof hex key (L).
Attaching the Monitor Mount
- Unscrew the VESA thumbscrews from the VESA receiver, remove the VESA plate, and set them aside.
- Attach the monitor mount to the arm and tighten the setscrew with the slotted screwdriver end of the hex key (L).
Attaching the VESA Plate to a Monitor
For larger monitors with 100×200 and 200×200 mm VESA holes
Attaching the VESA Plate to a Monitor (cont.)
Selecting the Right VESA Mounting Hardware for Your Display
A variety of screws are included to fit VESA standards on the backs of most
displays. Select the screws that best fit your display. Hand-thread the screws
to determine the correct diameter. Use the appropriately sized screws (M-A,
M-B, or M-C) and washers (M-D or M-E) to attach the VESA plate to the monitor.
Make sure the arrow on the VESA plate is pointing to the top of the monitor.
Important
The screws should be tightened until snug. Don’t over-tighten.
Attaching the Monitor
Hang the VESA plate and monitor on the VESA hooks.
Important
For large and heavy monitors, it’s recommended for two people to hang the
monitor.
Make sure the monitor is securely hanging on the VESA receiver before
releasing it. Then replace the VESA thumbscrews, and tighten until secure.
Balancing the Arm M
When the arm is adjusted to the ideal tension, it will hold the monitor in position indefinitely.
To adjust the arm tension, follow these steps: Support the monitor with one hand, and position the arm and monitor so the arm is horizontal.
- If the arm drops due to the weight of the monitor, use the hex key (M) to turn the arm tension screw counterclockwise toward the + icon.
- If the arm rises, use the hex key to turn the arm tension screw clockwise toward the – icon.
Important
Do not overtighten or loosen the tension adjustments.
Adjusting Arm Swivel
The three swivel points on the monitor mount can be adjusted by tightening or loosening the setscrews with the slotted end of the hex key (L).
Adjusting the Tilt Angle
If the tilt angle of the monitor won’t move, use the hex key (M) to slightly loosen the tilt tension screw by turning it toward the – icon.
Adjusting the Monitor Orientation
The monitor mount lets you rotate the screen by 90° in either direction. A safety screw is included to prevent over rotation
Organizing Cables
Power and monitor cables can be neatly run through the top and bottom cable guides on the arms.
Top Cable Guide
Use a Phillips screwdriver to unscrew the top cableguide screw, and slide it
up toward the monitor to remove it.
Botton Cable Guide
Remove the bottom cable guide by sliding it up toward the monitor. Place the
cables in the guide, align the notches, and slide the cable guide back toward
the base until it snaps into place.
Storing the Hex Keys
Store the hex keys and keep them handy for future adjustments by placing them
in the holder (F) and sliding the holder onto the slots on the back of the
base.
One-Year Limited Warranty
This Gabor product is warranted to the original purchaser to be free from
defects in materials and workmanship under normal consumer use for one (1)
year from the original purchase date or thirty (30) days after replacement,
whichever occurs later. The warranty provider’s responsibility concerning this
limited warranty shall be limited solely to repair or replacement, at the
provider’s discretion, of any product that fails during normal use of this
product in its intended manner and its intended environment. Inoperability of
the product or part(s) shall be determined by the warranty provider. If the
product has been discontinued, the warranty provider reserves the right to
replace it with a model of equivalent quality and function. This warranty does
not cover damage or defect caused by misuse, neglect, accident, alteration,
abuse, improper installation, or maintenance. EXCEPT AS PROVIDED HEREIN, THE
WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED
WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides
you with specific legal rights, and you may also have additional rights that
vary from state to state. To obtain warranty coverage, contact the Gabor
Customer Service Department to obtain a return merchandise authorization
(“RMA”) number, and return the defective product to Gabor along with the RMA
number and proof of purchase. Shipment of the defective product is at the
purchaser’s own risk and expense. For more information or to arrange
service, visit www.madebygabor.com or call
Customer Service at 212-594-2353.
Product warranty provided by the Gradus Group. www.gradusgroup.com
Gabor is a registered trademark of the Gradus
Group. © 2024 Gradus Group LLC. All Rights Reserved.
FAQ
Q: What tools are required for installation?
A: You will need a Phillips screwdriver and a hex key for installation.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>