dormakaba ES 250 PRO Sliding Door Unit Instruction Manual

: September 5, 2024
: dormakaba

Table of Contents

dormakaba ES 250 PRO Sliding Door Unit
Specifications
FAQs
About this document
Safety
Operation
Cleaning
Troubleshooting
CONTACT INFORMATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

dormakaba ES 250 PRO Sliding Door Unit

Specifications

Model: ES 250 PRO/ES 250 PRO FST, ES 400 PRO/ES 400 PROFST
Type: Sliding Door Unit
Operating Modes: Off operating mode, Partial opening width setting
Safety Features: Emergency stop switch, General safety instructions

FAQs

Q: What should I do if the door unit is not responding to commands?

A: If the door unit is not responding, check for the power supply, ensure safety switches are not activated, and refer to the troubleshooting section of the manual for further assistance. Q: Can I adjust the opening speed of the door?

A: Yes, you can adjust the opening speed of the door unit by following the instructions provided in the manual for adjusting operating parameters.

About this document

Contents and purpose

This manual enables the safe operation of the ES PROLINE sliding door unit (also referred to as “door unit” in the following). This manual constitutes a component of the product and must be stored in the immediate vicinity of the product so that it is accessible to personnel at all times. The facility operator must have read this manual prior to commissioning. Complying with all safety instructions and action steps provided in this manual is the basic prerequisite for handling the door unit safely.

Target group

This manual is aimed at the facility operator and the user of the ES PROLINE sliding door unit. The user must be instructed by the facility operator in the safe handling of the door unit.

Other applicable documents

Documentation for accessories used

Documents storage

This manual and the applicable documents must be kept during the service life of the product and must be passed on with the product.

Symbols used

Hazard categories

WARNING

This signal word indicates a possible hazardous situation that may result in death or serious injury if not averted.

CAUTION

This signal word indicates a possible hazardous situation that may result in minor or slight injury if not averted.

ATTENTION

This signal word indicates a possible hazardous situation that may result in damage to property or the environment if not averted.

Safety

Reasonably foreseeable misuse

Any use above and beyond the correct use is considered to be incorrect use.

General safety instructions

WARNING

Danger to life through electric current The danger of electric shock. Never insert metal objects into the openings on the operator. Do not allow any water or other fluids to get into the operator.

Danger points

Depending on the structural condition, door variant and protection option, residual risks exist at the closing edges, e.g. due to slight crushing or force-limited impacts.

Operation

Switching on the door unit

If the optional emergency stop switch or emergency open switch is locked (button is pushed in), turn the button to release the switch.
Set the required operating mode using the operating mode switch (see the manual for the operating mode switch).

The following operating modes can be set with the operating mode switch.

Off operating mode
- The door cannot be opened automatically.
Automatic operating mode
- The door opens and closes automatically.
Permanent open operating mode
- The door opens automatically and remains open while this operating mode is active.
Exit operating mode
- The door opens and closes automatically when someone approaches from the inside. The door cannot be opened from the outside.
Partial open operating mode
- The door opens automatically to the set partial opening width and closes automatically.

Changing the operating mode

Set the required operating mode using the operating mode switch (see the manual for the operating mode switch).

Setting the partial opening width

WARNING

Danger to life due to too small escape route

Danger at escape route sliding doors due to too small escape route.
- Adjust the partial opening width so that the required escape route width is not restricted.

The partial opening width can be set using the operating mode switch or via the web application. The option to set using the operating mode switch can be disabled in the web application.
Setting the partial opening width using the operating mode switch

Set the Off operating mode.
- The door closes.
Set the Permanent open operating mode.
- The door opens slowly.
When the required partial opening width is reached, set the Partial open operating mode.
- The door stops.
- The partial opening width is saved.
- The door closes.

Releasing the door manually

If a manual release is installed, the door can be released manually. To release the door manually, either pull the handle bar or push the button depending on the type of manual release.

Opening/closing the door in the event of power failure

Door unit with battery pack

Depending on the battery mode setting, the door opens or closes in the event of a power failure. The door can be opened/closed via the Night/Bank button.

Door unit without battery pack

The door unit is closed as follows, depending on the locking device type installed

Standard or fail-safe locking device

Close the door unit manually.
- The door unit cannot be locked.

Locking device type Fail-secure locking device

The door unit can only be closed if the door unit is released with an optional manual release

Commissioning the door after a power failure

After a short wait, the door unit resumes operation in the previously activated operating mode.

Switching off the door

Set the Off operating mode using the operating mode switch (see the manual for the operating mode switch).

The door closes.
If the door unit has an automatic locking device, the door unit is locked.
The door can be opened with a night/bank activator.

Fault LED on the operating mode switch

The fault LED lights up if an error occurs that impairs operation. The door remains the open position. The door can be closed by setting the Off operating mode so long as the displayed error does not prevent this.

The door closes slowly.
If a locking device is present, the door unit is locked.

Cleaning

WARNING

Danger to life through electric current

Danger of electric shock.
Never insert metal objects into the openings on the operator.
Do not allow any water or other fluids to get into the operator

CAUTION

The danger of injury from moving parts

Risk of impact and crushing by the door leaves.
Before commencing cleaning, switch the operating mode switch to Off or Permanently open operating mode and ensure this state for the duration of the cleaning work.

ATTENTION

Risk of damage to the surface
Do not use any objects with sharp edges or any aggressive cleaning agents.
- The sensors, the floor guide and area of movement must be kept free from contamination at all times.
- For units with an underfloor guide, the floor track must be cleaned on a regular basis.
- Clean the door unit with a damp cloth and commercial cleaners. To prevent any surface damage, do not use any abrasives.