ATEN VE2812PR HDMI HDBaseT Receiver with Audio User Guide

ATEN VE2812PR HDMI HDBaseT Receiver with Audio

Hardware Overview

Front View

1. audio out (coaxial)
2. audio out (stereo)
3. Audio channel switch
4. IR port
5. HDMI audio out switch
6. HDMI out
7. HDBaseT in
8. PoH PSE & PD switch
9. RS-232 serial port
10. RS-232 serial communication switch
11. long reach mode switch
12. firmware upgrade switch
13. power jack
14. HDMI out LED
15. link LED
16. PoH power LED
17. DC-in power LED

Note: The firmware upgrade switch is reserved for tech support. If you would like to do a fi rmware upgrade yourself, please contact ATEN technical support.

Installation

1. Before installation, please make sure the VE2812PR is set to PoH PSE or PoH PD mode using the DIP switch for your installation requirement.

   • Set the PoH PSE & PD switch to PSE: The VE2812PR receives power from the power adapter and delivers power to a PoH PD-supported device through its HDBaseT input port.
   • Set the PoH PSE & PD switch to PD: The VE2812PR receives power from a PoH PSE-supported device through its HDBaseT input port.

2. Use a grounding wire to ground the unit by connecting one end to the grounding terminal, and the other end to a suitable grounded object.
   Note: Do not omit this step. Proper grounding helps prevent damage to the unit from power surges or static electricity.

3. Connect an HDMI-enabled display to the unit’s HDMI output port.

4.  Follow the steps below to set up your audio output.

   • To use an independent speaker, connect the speaker to the unit’s audio output port (coaxial or stereo) using an appropriate audio cable.
   • Depending on the interface of your chosen audio output device, adjust the audio channel switch if necessary
     Audio Interface| Audio Channel Switch| Description
     ---|---|---
     Stereo| 2 ch| Sets the audio output to channel 2.
     Coaxial| 5.1 ch| Sets the audio output to channel 5.1.
     HDMI| Auto| Detects the supported audio channel of the connected HDMI display.

Note: The stereo audio will be muted if the channel is set to Ch 5.1. (c) To mute the audio on the connected HDMI display, put the HDMI audio out switch to OFF.

5. Connect a video transmitter’s HDBaseT output port to the unit’s HDBaseT input port using a Cat 6a / ATEN 2L-2910 cable.
   Note: ATEN recommends pairing the VE2812PR with VE2812AT.

6. (Optional) To bypass IR signals to remotely control a device (e.g., Blu-ray player) connected to the video transmitter, connect an IR receiver to the unit’s IR port and an IR emitter to the VE2812AT’s IR port.
   Note: To purchase an IR receiver and an IR emitter, please contact your ATEN dealer for more information.

7. (Optional) You can use the RS-232 serial port to do one of the following:

   •  To control the VE2812AT using an ATEN controller, connect the ATEN controller to the unit’s RS-232 serial port and then put the RS-232 serial

8. (Optional) Connect the power adapter to the unit’s power jack or connect a PoH PSE-supported device to the unit’s HDBaseT input port for power supply and operation.

Package Contents

• 1VE2812PR HDMI HDBaseT
• Receiver with Audio De-Embedding /
• Bi-directional PoH
• 1 RS-232 terminal block
• 1 foot pad set (4 pcs)
• 1 power adapter
• 1 user instructions

Long Reach Mode

To extend the VE2812PR’s 1080p signals up to 150 m, put the long reach mode switch to ON.

Support and Documentation Notice

All information, documentation, firmware, software utilities, and specifications contained in this package are subject to change without prior notification by the manufacturer.
To reduce the environmental impact of our products, ATEN documentation and software can be found online at http://www.aten.com/download/ Technical Support www.aten.com/support

References

• ATEN - Simply Better Connections | ATEN U.S.A.
• Downloads | ATEN Corporate Headquarters

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>