Ledvion LV40010 LED Fixtures Instruction Manual
- May 15, 2024
- Ledvion
Table of Contents
Ledvion LV40010 LED Fixtures
Product Specifications:
- Model: LV40010
- Watt: 20W, 36W, 48W
- Fixture Lumen: 2400Lm, 4320Lm, 5760Lm
- IP Value: IP65
- CRI: >80
- CCT: 4000K, 6500K
- Dimmable: No
- IK Rating: IK08
- Dimensions: Vary based on model – refer to manual
- Input Power: AC: 220-240V, 50/60Hz
Product Usage Instructions
Installation:
- Ensure the power source is turned off before installation.
- Mount the fixture securely using appropriate mounting hardware and follow the manual for specific instructions.
Operation:
- Turn on the power source and switch on the light using the designated switch.
- Do not attempt to modify or disassemble the product while in operation.
Maintenance:
- Regularly clean the fixture with a soft, dry cloth to remove dust and debris.
- Check for any signs of damage or wear and tear periodically and replace any faulty parts immediately.
Safety Precautions:
- Do not expose the fixture to water or moisture unless specified as waterproof.
- Keep the product away from direct sunlight or extreme temperatures to ensure longevity.
Frequently Asked Questions (FAQ):
Q: Is the product suitable for outdoor use?
A: Yes, the product has an IP65 rating, making it suitable for outdoor
environments where it may be exposed to dust and low-pressure water jets.
Q: Can the product be used with a dimmer switch?
A: No, the product is not dimmable and should not be connected to a
dimmer switch as it may cause damage.
Q: What is the recommended voltage for this product?
A: The product operates on AC 220-240V, 50/60Hz power input.
Ensure your power supply matches these specifications for safe operation.
INSTALLATION INSTRUCTIONS
Attention
Installation should only be done by persons with electro-technical knowledge
and experience. These products are not suitable for installation at locations
near the sea or in other environments with a corrosive atmosphere.
TECHNICAL DATA
Model| Watt| Fixture Lumen| IP Value| CRI| CCT|
Dimmable| IK Rating| Dimensions| Input Power
---|---|---|---|---|---|---|---|---|---
LV40010| 20W| 2400Lm| IP65| >80| 4000K| No| IK08| 626 x 63 x 57 mm| AC:
220-240V, 50/60Hz
LV40011| 20W| 2400Lm| IP65| >80| 6500K| No| IK08| 626 x 63 x 57 mm| AC:
220-240V, 50/60Hz
LV40012| 36W| 4320Lm| IP65| >80| 4000K| No| IK08| 1206 x 63 x 57 mm| AC:
220-240V, 50/60Hz
LV40013| 36W| 4320Lm| IP65| >80| 6500K| No| IK08| 1206 x 63 x 57 mm| AC:
220-240V, 50/60Hz
LV40014| 48W| 5760Lm| IP65| >80| 4000K| No| IK08| 1496 x 63 x 57 mm| AC:
220-240V, 50/60Hz
LV40015| 48W| 5760Lm| IP65| >80| 6500K| No| IK08| 1496 x 63 x 57 mm| AC:
220-240V, 50/60Hz
IP65 FIXTURE
INSTALLATION INSTRUCTION
WARNING!
- Please make sure to turn off the power before starting the installation.
- The light source of this luminaire is not replaceable, when the light source reaches its end of life the whole luminaire should be replaced.
- Before installation, you must carefully check the integrity of the product and accessories.
- When installed, products and flammable materials to ensure that at least 0.2m distance, lightning cannot be installed in the zenith or heat wall, pay attention to low voltage and high voltage electrical wiring separately.
- If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a simalar qualified person in order to avoid a hazard.
- To ensure that the power cord has enough length, do not kink cables. Output cables should be laid separately and at a distance from other cables.
- Install only by certified electrician.
INSTALLATION INSTRUCTIONS
- Choose the right position, drill two hole and insert the screw (make sure the distance between the holes is no less than S0mm, Less than bracket length).
- Shrapnel point it at the hole and then install the screws.
- Press the lamp body firmly into the mounting buckle to fix the lamp body, Slide the lamp body along the mounting buckle to the desired position as needed.
- Connect the wiring, use insulating tape, and waterproof tape for insultion and waterproofing, turn the power ON and test.
PACKING:
- IP65 Fixture (lPC)
- Instruction Manual (lPC)
- Cable gland, clips & screws
INSTALLATION:
STEP 1
STEP 2
STEP 3
STEP 4
Notes on Disposal
The product is designated for separate collection at an appropriate collection
point.
Do not dispose of the product with household waste. For more information,
contact the retailer or the local authority responsible for waste management.
Care
Before cleaning the unit, disconnect it, if necessary form other components;
do not use aggressive cleaning agents. The unit has been carefully checked for
defects. If nevertheless you do have cause for complaint, please go back to
the retailer where you have bought the product together with your proof of
purchase. We are not liable for damage arising from incorrect handling,
improper use or wear or tear. We reserve the right to make technical
modifications.
General Safety
-
Read the manual carefully before use. Keep this manual for future reference.
-
Only use the product for its intended purposes. Do not use the product for other purposes than described in the manual.
-
Do not use this product if any part is damaged or defective. If the product is damaged or defective, replace the product immediately.
-
This product shall not be used by children without the supervision of an adult.
Children shall not play with the device. -
Do not modify the product in any way.
- Do not expose the product to water or moisture. (IP 20)
- Do not immerge the product into water. (IP 44 – (P 67)
-
Keep the product away from heat sources.
-
Do not block the ventilation openings.
-
Do not look directly into the LED lamp.
-
Keep a minimum distance of 1 meter between the lamp and the surface being illuminated.
Electrical safety
- To reduce risk of electric shock, this product should only be opened by an authorized technician when service is required.
- Do not use the product if the cable or plug is damaged or defective. When damaged or defective, it must be replaced by the manufacturer or an authorised repair agent.
- Before use, always make sure that the voltage is the same as the voltage on the rating plate of the device.
Make sure that the cable does not hang over the edge of a worktop and cannot be caught accidentally or tripped over.
Warning
- The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
- Caution, risk of electric shock.
- The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire has to be destroyed
Disclaimer
Designs and specifications are subject to change without notice. All logos,
brands and product names are trademarks or registered trademarks or their
respective holders and are hereby recognized as such.
Please visit us online on our website:
www.ledvion.com For more information about our
company and our products.
Documentation
The product has been manufactured and supplied in compliance with all relevant
regulations and directives, valid for all member states of the European Union.
The product complies with all applicable specifications and regulations in the
country of sales.
Formal documentation is available upon request. The formal documentation
includes, but is not limited to the Declaration of Conformity, the Material
Safety Data
Sheet and the product test report.
CE declaration
This product complies with the following directives:
- LVD: 2014/35/EU
- EMC: 2014/30/EU
- RoHS: 2011/65/EU
Additionally, for Products with Radio transmitter units:
RED: 2014/53/EU
The complete Declaration of Conformity Document (DOC) can be found on our
website.
IP65 BATTEN
INTEGRATED LED
5692 DH Son en Breugel
Ekkersrijt 4304
The Netherlands
www.ledvion.com
LV40010, LV40011, LV40012, LV40013, LV40014 & LV40015