Pioneer DJ XPRS2 Series Active Loudspeaker / Subwoofer Instruction Manual

Pioneer DJ XPRS2 Series Active Loudspeaker / Subwoofer

Product Information

Specifications:

• Model Series: XPRS2
• Models: XPRS82, XPRS102, XPRS122, XPRS152, XPRS1152ST, XPRS1182ST
• Type: Active Loudspeaker / Active Subwoofer
• Website: pioneerdj.com/support/

Main Features:

• Integrated pull-back cover
• Digital Signal Processing (DSP)
• Multiple input options including balanced inputs for instruments and microphones
• Signal lights for Hl-Z, MIC, and single channel signals
• LCD DSP control and monitoring interface
• MIX OUT for sending mixed signals to other speakers or subwoofers

Product Usage Instructions

Rear Panel (Full-Range Models):

1. AC Input: Connect the power cord to AC IN and then to the power outlet.
2. POWER Switch: AC switch for turning the power  on or off. When POWER is turned ON, the POWER LED and the LCD screen both light up.

DSP Control:

1. To access the DSP control menu:
2. Press the MASTER VOL knob to bring up the menu.
3. Use the MASTER VOL knob to navigate through menu items.
4. Select a menu item by pressing the MASTER VOL knob.
5. Adjust settings using the MASTER VOL knob and save selections.

Rear Panel (Subwoofer Model):

1. AC Input: The AC connection is established via the IEC connector. The IEC connector is compatible with a lockout power cord (not included).
2. POWER Switch: AC switch for turning the power on or off. When POWER is turned on, the LED lights up.

FAQ:

1. Q: How do I connect external devices to the speaker?
   A: You can connect external devices such as mixing consoles, instruments, or microphones using the balanced inputs with 1/4-inch TRS or XLR connectors.

pioneerdj.com/support/
For other support information for this product, visit the above site.

How to read this manual
Thank you for choosing this speaker. To make sure you get the most from its functions and use them effectively, please read the Instruction manual and Precautions for Use carefully.
Please keep the Instruction manual and Precautions for Use together with the Warranty.

Main features

2 000-W high output and high sound quality are achieved by mounting a D-class amplifier module in a wooden cabinet featuring outstanding acoustic characteristics. The XPRS2 can be used not only as a stationary sound system in a stationary facility but also as sound equipment for events as it can be easily transported and set up quickly.

• System type: Multi-purpose, active loudspeaker with DSP controls
• Transducer driver: 1-inch exit compression driver, 1.75-inch voice coil
• Subwoofer: ferrite woofer, 3-inch (76 mm) voice coil with long excursion
• Power rating: Class D 2 000 W (peak)
• 4 DSP modes: LIVE/MUSIC/SPEECH/MONITOR
• Subwoofer: 80 Hz, 100 Hz, 120 Hz (NORMAL, BOOST, EXTENDED LF)
• Electronic protections: Thermal/overload/digital limiter/compressor
• Power supply: AC 110 V – 240 V (50 Hz / 60 Hz)
• Enclosure construction: Plywood cabinet, black paint, rubber feet, metal handle
• Mounting: One metal standard pole-mount, 10 x M10 threaded inserts plus integrated pull-back cover

Rear panel

(full-range models)

1. AC INPUT
   Connect the power cord to AC IN and then to the power outlet.

2. POWER
   AC switch for turning the power on or off. When POWER is turned ON, the POWER LED and the LCD screen both light up.

3. INPUT1
   Level control for the LINE/MIC INPUT 1.
   INPUT
   Balanced input for sources such as mixing consoles, instruments, or microphones. Connections can be made via a 1/4-inch TRS or XLR connector.

4. INPUT2
   Level control for the Hl-Z/LINE INPUT 2.
   INPUT
   Balanced input for sources such as mixing consoles, instruments, or microphones. Connections can be made using a 1/4-inch TRS or XLR connector.

5. STEREO LEVEL
   Line input level control for STEREO.

6. INPUT LEVEL
   Level control of the individual input.

7. Hl-Z signal light
   When sound from a guitar is input, the system setting changes to Hl-Z sensitivity and the signal light turns on.

8. 8 MIC signal light
   When sound from a microphone is input, the light turns on when the system setting changes to MIC sensitivity.

9. SIG single channel signal light
   When there is a signal, the signal light turns on.

10. LCD
    DSP control and monitoring interface.

11. MASTER VOL
    Total volume adjustment range: -60 dB – +10 dB.
    DSP
    Scroll through the menus and choose from the options. Press the MASTER VOL knob to select an item on a menu.

12. SIG/LIMITER signal light
    Lights up green when there is a signal, and red when the amplifier starts to compress.

13. POWER indicators
    Llights up when the speaker is turned on.

14. MIX OUT
    The XLR output sends mixed input signals to other speakers or subwoofers. INPUT LEVEL controls the level of the signal sent to the MIX OUT. The MASTER VOL or DSP control settings do not affect the mixed output.

Rear panel
(subwoofer model)

1. AC INPUT
   The AC connection is established via the IEC connector. The IEC connector is compatible with a lockout power cord (not included).

2. POWER
   AC switch for turning the power on or off. When POWER is turned on, the LED lights up.

3. LINK
   The XLR output sends mixed input signals to other speakers or subwoofers. VOLUME (input level) controls the level of signal sent to LINK. The MASTER VOL and DSP control settings do not affect the LINK signal.

4. INPUT LEFT (mono)/RIGHT

5. POWER indicators
   The POWER LED lights up when the speaker is turned on.

6. SIG/LIMITER signal light
   Lights up green when there is a signal, and red when the amplifier starts to compress.

7. 3DSP PRESET MODES
   BOOST/EXTENDED LF/NORMAL

8. LPF
   80 Hz/100 Hz/120 Hz

9. POLARITY
   REVERSE/NORMAL

10. VOLUME
    Level control of an input signal.

DSP control

With the integrated DSP control menu, you can choose from multiple DSP and system settings on the speaker.
To access the DSP control menu, follow the steps below.

1. Press the MASTER VOL knob and the DSP control menu will appear.

2. Use the MASTER VOL knob to scroll through the menu items.

3. Press the MASTER VOL knob to select the menu item you want to modify.
   The menu item you chose will open on the right side of the DSP menu.

4. Use the MASTER VOL knob to scroll through the menu items.

5. Press the MASTER VOL knob to select a setting.
   The setting will be saved and you will return to the level above in the menu.

6. Repeat steps 2 through 5 to modify other DSP and system settings.

7. Select EXIT to return to the main screen.

Full-range speaker DSP control menu
Full-range speaker DSP control menus are included on the XPRS82, XPRS102, XPRS122 and XPRS152 units.

EXIT menu item
Use the EXIT menu item to return to the home screen.

NOTE
After a minute of menu inactivity, the display turns off but the speaker continues working as normal.

MENU **

**

You can use the Input Settings menu to configure the speaker’s input sensitivity control as well as the Delay and Phase control settings.

The MIC setting is for the Input 1 input sensitivity control. After selecting the MIC input, the MIC light on the panel will turn on.
The Hl-Z setting is for the input 2 input sensitivity control. After selecting the Hl-Z input, the Hl-Z light on the panel will turn on.
The Delay menu is for creating time calibrations with other speakers. The options available range between 0 and 69.19 feet. The delay can be changed in increments of 0.69 feet. The default setting is 0 feet.
Phase setting preset for the entire loudspeaker system.
The Factory Presets menu is for configuring the type of sound the speaker sends. The options are: LIVE, MUSIC, SPEECH, and MONITOR. You can use the MASTER VOL menu button to configure the presets for different situations.

• LIVE – for live sound applications (default).
• MUSIC – for recording music and playing dance music.
• SPEECH – for voice-only applications.
• MONITOR – for ground monitoring.

The Sub Setting menu is for selecting the high-pass frequency or matching subwoofer when one is used in the speaker setup. The options available for this selection are: No Sub, 80 Hz (80 Hz), 100 Hz (100 Hz), 120 Hz (120 Hz), 150 Hz (150 Hz), and the Qualcomm is a 24 dB/octave Linkwitz/Riley crossover. The 80 Hz (100 Hz), 100 Hz (100 Hz), 120 Hz (120 Hz), and 150 Hz (150 Hz) options are general high-pass settings for use with other subwoofers. The settings are optimized for the woofer (including delays for optimal overlay).
The default is No Sub.

EQ menu

The EQ menu is a 4-band EQ (equalizer) that you can fine tune in addition to FUNCTION and LOCATION. The options available are: HI, MD, LM, and LO.

Back

HI| 12.1K| Default: 0 decibels
MD| 2.52K| Range: -18 decibels – +18 decibels
LM| 500.0| ALLBYPASS will be deleted, invalidating all set EQs.
LO| 101.5| FLAT is to restore all adjusted EQs to factory settings.

NOTE
The indoor equalizer (EQ) range shown is the factory default range for individual speakers. When the woofer is selected, any EQ below the crossover point is bypassed.
To use EQ above the crossover point, do the following.

Rotate the MASTER VOL knob to reach the desired frequency.

User Programs (saved user settings)

There are 16 presets that you can change and save EQ values for. You can also give them custom names with 7 English letters/symbols. Use the load/save/delete options to do this.

System menu

The System menu is for configuring the system. You can also configure the accessibility of this menu and modify the settings, and reset to factory defaults.
The FIRMWARE/HARDWARE menu displays the current preset and firmware version.

The Name menu shows the name of the current speaker. This menu enables you to customize the name of the speaker.
The Default Settings menu is for resetting the speakers to their original factory settings. The options for this selection are: NO or YES.
The Exit menu is for returning to the main menu.
To reset your system to the original factory settings, follow the steps below.

1. From the System menu in the DSP menu, select Default Settings. A message prompt to restore the factory settings will appear.
2. Select Yes.
3. When the prompt asks if you’re sure, select Yes.

The speaker will reboot the system and reset to the original factory settings.

Installation and connections

Important notes on installation
The sound produced by the speaker is subtly influenced by the conditions of the room you use it in. Carefully consider the installation location before setting up the speaker to ensure the best possible conditions. AlphaTheta Corporation will not be liable for any damages arising from use of the speaker (including but not limited to loss of business opportunities), regardless of the installation method used.
Be sure to use the handles on the top or the sides of the speaker when moving and installing it.

CAUTION

• To help proper cooling, please make sure enough space is kept between each speaker and nearby walls or other components (minimum 30 cm or more above, behind, and to the sides of each speaker). Leaving insufficient space may cause the temperature inside the speaker to rise, leading to malfunction or permanent damage.
• Use of this product while it is stacked is prohibited.

Installation using a speaker pole
XPRS82/XPRS102/XPRS122/XPRS152
The full-range models of the XPRS2 Series have a 35-mm-diameter pole socket on the bottom surface.
The subwoofer model of the XPRS2 Series have an M20 screw-in pole socket on the top surface in which the pole can be secured firmly.
The combinations shown in the following diagrams are recommended for the XPRS2 Series. Using a different combination may result in the speakers toppling over and possibly causing damage or injury. To use a speaker pole, check the cautions below and perform the installation safely.

CAUTION

• At least two people should lift each speaker together to install it. Be sure to give enough consideration to safety when performing the work.
• Use a 35-mm-diameter, one-side M20 screw-in speaker pole. Use a commercially-available product with a length of 900 mm or less. AlphaTheta Corporation will not be liable for any damages (including but not limited to loss of business opportunities) arising from the use of a speaker pole other than the type specified.
• Install the subwoofer in a stable, horizontal location and secure the speaker pole firmly.
• Ensure there is no danger of speakers toppling over.
• Cables should be taped or tied together with suitable tape or cable ties to avoid the danger of tripping on the cables and causing the speakers to topple over.

Pole socket

Installation using a speaker pole

Installation using the rigging points on the speaker

• The full-range models have suspension-mounting rigging points on them. The speaker can be suspended using commercially-available eye bolts. The rigging point has an M10 screw hole (for an eye bolt with a thread length of 30 mm – 50 mm).
• When installing the speaker suspended, ask a qualified technician to perform the work.
• Remove the screws from the rigging points on the speaker and attach eye bolts. Do not use the speaker while the screws are removed. The sound will be adversely affected by air leakage.
• Be sure to use at least three rigging points to suspend the speaker. Furthermore, be sure to also implement an extra safety measure such as using a wire.
• Use brackets, wires, and a wall or ceiling strong enough to bear the weight of the speaker. Ask for commercially-available brackets at the shop where you purchased the speaker.
• Be sure to confirm the safety after installing the speaker and periodically thereafter.

Connections

For active full-range speaker system
CAUTION
Make your initial connections with all the equipment powered off and ensure all the main volume controls are turned down completely.

1. Connect one end of a signal cable to the Output Left/Right on your mixer (with a stereo jack or XLR connector) and connect the other end of the cable to the Line Input (COMBO) on your active speaker (with a stereo jack or XLR connector).
2. Connect the power cord to a mains supply.
3. Turn on your mixer first, then the active speakers.
4. Turn up the volume control of the speakers.
5. Use the PFL function on the mixer to get the proper input level, and adjust the Main Mix Level control to reach the desired output level.
6. When finished, turn off your active speakers first, then the mixer.

Active subwoofer and active satellite speaker

CAUTION
Make your initial connections with all the equipment powered off and ensure all the main volume controls are turned down completely.

1. Connect one end of a signal cable to the Output Left/Right on your mixer and connect the other end of the cable to the Line Input on the corresponding (left or right) active subwoofer.
2. Connect one end of another signal cable into the Link Left/Right or Out Left/Right of the active subwoofer, and connect the other end to the Line Input Left/Right of the active satellite speaker.
3. Connect the power cord to a mains supply.
4. Turn on your mixer first, then the active speakers.
5. Turn up the volume control of the active speakers.
6. Use the PFL function on the mixer to get the proper input level, and adjust the Main Mix Level control to reach the desired output level.
7. When finished, turn off your active speakers first, then the mixer.

The direction of the arrow indicates the signal path.

Specifications

MINI Output: MIX (XLR)
Power supply| AC 110 V – 240 V (50 Hz / 60 Hz)
Power consumption| 800 W (OFF : 0 W)
Enclosure construction| Plywood cabinet, black paint, rubber feet, metal handle
Mounting| One standard metal pole-mount. 10 x M10 threaded inserts plus integrated pull-back cover.
Dimensions (W x H x D)| 10.74” (272.7 mm) x 18.11” (460 mm) x 11.88” (302 mm)
Net weight| 13.2 kg (29.1 lb)
Model| XPRS102
---|---
System type| Multi-purpose, 2-way active loudspeaker with DSP controls
Transducer low| 10” woofer, 2.5” voice coil
Transducer driver| 1” exit compression driver, 1.75” voice coil
Frequency response (-6 dB)| 50 Hz – 20 kHz
Max SPL| 129 dB
Power rating| Class D 2 000 W (peak)
4 DSP modes| LIVE / MUSIC / SPEECH / MONITOR
Electronic protections| Thermal / overload / digital Limiter / compressor
Connectors| Input: MIC / LINE (Combo) / HI-Z / LINE (Combo) / 3.5 mm STEREO MINI Output: MIX (XLR)
Power supply| AC 110 V – 240 V (50 Hz / 60 Hz)
Power consumption| 800 W (OFF : 0 W)
Enclosure construction| Plywood cabinet, black paint, rubber feet, metal handle
Mounting| One standard metal pole-mount. 10 x M10 threaded inserts plus integrated pull-back cover.
Dimensions (W x H x D)| 11.77” (299 mm) x 20.5” (520 mm) x 12.2” (310 mm)
Net weight| 15.5 kg (34.2 lb)
Model| XPRS122
---|---
System type| Multi-purpose, 2-way active loudspeaker with DSP controls
Transducer low| 12” woofer, 3” voice coil
Transducer driver| 1” exit compression driver, 1.75” voice coil
Frequency response (-6 dB)| 48 Hz – 20 kHz
Max SPL| 131 dB
Power rating| Class D 2 000 W (peak)
4 DSP modes| LIVE / MUSIC / SPEECH / MONITOR
Electronic Protections| Thermal / overload / digital limiter / compressor
Connectors| Input: MIC / LINE (Combo) / HI-Z / LINE (Combo) / 3.5 mm STEREO MINI Output: MIX (XLR)
Power supply| AC 110 V – 240 V (50 Hz / 60 Hz)
Power consumption| 800 W (OFF : 0 W)
Enclosure construction| Plywood cabinet, black paint, rubber feet, metal handle
Mounting| One standard metal pole-mount. 10 x M10 threaded inserts plus integrated pull-back cover.
Dimensions (W x H x D)| 14.28” (362.7 mm) x 25.07” (637 mm) x 13.78” (350 mm)
Net weight| 20.2 kg (44.6 lb)
Model| XPRS152
---|---
System type| Multi-purpose, 2-way active loudspeaker with DSP controls
Transducer low| 15” woofer, 3” voice coil
Transducer driver| 1” exit compression driver, 1.75” voice coil
Frequency response (-6 dB)| 45 Hz – 20 kHz
Max SPL| 133 dB
Power rating| Class D 2 000 W (peak)
4 DSP modes| LIVE / MUSIC / SPEECH / MONITOR
Electronic Protections| Thermal / overload / digital limiter / compressor
Connectors| Input: MIC / LINE (Combo) / HI-Z / LINE (Combo) / 3.5 mm STEREO MINI Output: MIX (XLR)
Power supply| AC 110 V – 240 V (50 Hz / 60 Hz)
Power consumption| 800 W (OFF : 0 W)
Enclosure construction| Plywood cabinet, black paint, rubber feet, metal handle
Mounting| One standard metal pole-mount. 10 x M10 threaded inserts plus integrated pull-back cover.
Dimensions (W x H x D)| 16.57” (421 mm) x 28.58” (726 mm) x 16.14” (410 mm)
Net weight| 25.2 kg (55.6 lb)
Model| XPRS1152ST
---|---
System type| 15” active vented subwoofer
Power rating| Class D 4 000 W (peak)
Transducer low| 15” ferrite woofer, 3” (76 mm) voice coil with long excursion
Frequency response (-6 dB)| 45 Hz – 120 Hz
Max.SPL| 129 dB
DSP presets modes| BOOST / EXTENDED LF / NORMAL
Crossover frequency| 80 Hz / 100 Hz / 120 Hz low pass filter
Electronic protections| Over heat protection / short circuit protection / digital compressor
Cooling| Temperature-controlled fan
Connectors| Input: Left Mono (Combo) / Right (Combo), Output: Left Mono (XLR) / Right (XLR)
External controls| Volume control / phase switch / switch for EQ mode selector / switch for LPF / power on with green LED / limiter with red LED
Power supply| AC 110 V – 240 V (50 Hz / 60 Hz)
Power consumption| 800 W (OFF : 0.1 W)
Enclosure construction| Plywood cabinet, black paint, metal grille with foam, rubber feet, double handles
Mounting| One standard metal pole-mount. M20 screw socket.
Dimensions (W x H x D)| 22.83” (580 mm) x 17.72” (450 mm) x 19.80” (503 mm)
Net weight| 26.6 kg (58.7 Ib)
Model| XPRS1182ST
---|---
System type| 18” active vented subwoofer
Power rating| Class D 4 000 W (peak)
Transducer low| 18” ferrite woofer, 3” (76 mm) voice coil with long excursion
Frequency response (-6 dB)| 40 Hz – 120 Hz
Max.SPL| 130 dB
DSP presets modes| BOOST / EXTENDED LF / NORMAL
Crossover frequency| 80 Hz / 100 Hz / 120 Hz low pass filter
Electronic protections| Over heat protection / short circuit protection / digital compressor
Cooling| Temperature-controlled fan
Connectors| Input: Left Mono (Combo) / Right (XLR-F), Output: Left Mono / Right (XLR-M)
External controls| Volume control / phase switch / switch for EQ mode selector / switch for LPF / power on with green LED / limiter with red LED
Power supply| AC 110 V – 240 V (50 Hz / 60 Hz)
Power consumption| 800 W (OFF : 0.1 W)
Enclosure construction| Plywood cabinet, black paint, metal grille with foam, rubber feet, double handles
Mounting| One standard metal pole-mount. M20 screw socket.
Dimensions (W x H x D)| 26.02” (661 mm) x 21.06” (535 mm) x 21.12”
(536.5 mm)
Net weight| 32.6 kg (71.9 Ib)

The specifications and design of this product are subject to change without notice.
© 2023 AlphaTheta Corporation. All rights reserved.

AlphaTheta Corporation
6F, Yokohama i-Mark Place, 4-4-5 Minatomirai, Nishi-ku, Yokohama, Kanagawa 220-0012 JAPAN / JAPON

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>