dormakaba RCI 910NTC Narrow Touchless Switch Installation Guide
- August 31, 2024
- dormakaba
Table of Contents
dormakaba RCI 910NTC Narrow Touchless Switch
Specifications
- Operating Voltage: +10 ~ +24VDC
- Operating Current: 100mA max @ 12VDC
- Operating Temperature: -10°C ~ +50°C
- Relay Output: 1A @ 30VDC
- Read Range:
- 3 ~ 5cm (Capacitance)
- 5 ~ 10cm (Infrared)
- 5 ~ 7cm (Combined)
- Operating Humidity: 10 ~ 90%
Product Usage Instructions
Switch Installation
- Separate the switch from the back plate by unlatching at the bottom of the switch.
- Wire as per the terminal chart provided.
- Set DIP switches 1, 2, and 3 for the desired unlock time (1 to 7 seconds) as per the chart.
- Set DIP switches 4 thru 8 as per the definition chart.
- Secure the back plate in place using the screws provided.
- Reattach the switch by snapping it onto the back plate. Press downward and apply pressure near the bottom until the switch snaps into place.
FAQ
-
Q: What should I do if the switch does not respond?
A: Check the wiring connections to ensure they are correct and secure. Also, verify that the power input is within the specified range. -
Q: How do I adjust the unlock time of the switch?
A: Set DIP switches 1, 2, and 3 to configure the desired unlock time between 1 to 7 seconds. Refer to the chart for specific settings.
INSTALLATION
RCI 910NTC
NARROW TOUCHLESS SWITCH
The RCI 910NTC is a dual technologies (Capacitance & Infrared) contactless
button. It has a mechanical override provided as back up in case of power or
electronic failure. A good choice for mullion mounted applications.
Features
- Mullion mounted applications
- 1 – 7 second activation time or Toggle mode
- 12-24VDC
- Base Unit current draw @ 12VDC = 27mA resting, 39mA activated @ 24VDC = 17.5mA resting, 23.2mA activated
- Secondary mechanical switch on Normally Open Circuit – Max. 100mA
- Selectable Capacitive or Infrared or both sensor activations
- Optional wireless transmitter and receiver available as accessories
- Selectable beeper options: permanently on/off or temporary on/off
- Sync to ground REX input
Mounting Dimensions
Switch Installation:
-
Separate the switch from the back plate by unlatching at the bottom of the switch.
-
Wire as per the terminal chart on page 2.
-
Set DIP switches 1, 2 and 3 for desired unlock time (1 to 7 seconds) per chart on page 2.
If Dip switches 1, 2 and 3 are all OFF = Toggle mode. -
Set DIP switches 4 thru 8 per the definition chart on page 2.
-
Secure the back plate in place using screws provided.
-
Reattach the switch by snapping onto the back plate.
-
Press downward and apply pressure near the bottom until the switch snaps into place.
Specifications
| Operating Voltage: | +10 ~ +24VDC | Relay Output: | 1A @ 30VDC |
|---|---|---|---|
| Operating Current: | 100mA max @ 12VDC | Read Range: | 3 ~ 5cm |
(Capacitance) 5 ~ 10cm (Infrared)
5 ~ 7cm (Combined)
Operating Temperature:| -10 ~ 70°C| Operating Humidity:| 10 ~ 90%
Wiring Terminals:
| No. | Color | Label | Description |
|---|---|---|---|
| 1 | Blue | MO | Manually open the door input, Active low |
| 2 | Red | VDC | Power input (+10V ~ +24VDC) |
| 3 | Black | GRD | Grounding |
| 4 | Brown | RTE_NO | **** Relay output (Dry contact) |
| 5 | Orange | RTE_COMM | |
| 6 | Purple | RTE_NC |
Dip Switch Definition:
1
| ON| ****
Adjust working mode and relay activation time
| **** Latching| Enable: Dip Switches 1-3 OFF Disable: Just 1 of 1-3 Dip Switches ON| Trigger once, the relay maintains open, green LED lights.
Trigger again, the relay output close, green LED goes out, blue LED lights.
---|---|---|---|---|---
OFF
2| ON| **** Timing (1 – 7
seconds)
| D-SW1| ON| OFF| ON| OFF| ON| OFF| ON
OFF| D-SW2| OFF| ON| ON| OFF| OFF| ON| ON
3| ON| D-SW3| OFF| OFF| OFF| ON| ON| ON| ON
OFF| Time| 1| 2| 3| 4| 5| 6| 7
4| ON| Manage Infrared induction| Turn OFF infrared
OFF| Turn ON infrared (Default)
5| ON| Buzzer control| Turn OFF the beep
OFF| Turn ON the beep (Default)
6| ON| Normal| Normal (Default)
OFF| Anti-interference| Can be turned on when there is interference source in
the field (Only for capacitance)
7| ON| Manage Capacitance| Turn OFF capacitance
OFF| Turn ON capacitance (*Default)
8| N/A| N/A| N/A
NOTE: **Do not turn OFF both Infrared (Dip Switch 4) and Capacitance (Dip Switch 7) induction at the same time, otherwise the 910NTC will become a normal mechanical contact exit button.
FCC Regulatory Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
© 2024 dormakaba Canada Inc
www.dormakaba.us
Phone: 1.800.265.6630
E-mail: sales_RCI@dormakaba.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>