HARVEST TEC 335Z 55 Gallon Automatic Preservative Applicator Installation Guide

HARVEST TEC 335Z 55 Gallon Automatic Preservative Applicator

Specifications

• Model: 335Z
• Product Name: 55 Gallon Automatic Preservative Applicator
• Installation Manual: 335Z-24-INST-Imp&Metric

Product Information

• The 335Z Automatic Preservative Applicator is designed to efficiently apply preservatives to hay bales during the baling process.
• It is compatible with the iPad Integration Module for enhanced functionality.

Installation Instructions

• Using a lift, position the assembly under the cab of the baler.
• Align part numbers 001-4703ZR-D2 with the holes in the front part of the baler.
• Mark and drill four half-inch holes at the ends of parts 001-4703ZR-A and 001-4703ZR-B to secure the assembly.
• Ensure not to drill into hydraulic lines or electrical wires.

FAQ

• Q: What version of the Hay App is required for operation with the iPad Integration Module?
• A: The Hay App version must be at least 2.7.1 or higher to operate with the iPad Integration Module (030-6672C).
• Q: How should I handle the moisture sensing pads installation if my baler already has a factory moisture system?
• A: If your baler already has a factory moisture system, you can use the factory moisture disc. However, make sure to disconnect the wires leading to both sensors and tape them up. Do not connect both the baler’s moisture wires and Harvest Tec’s moisture wires to the moisture disc simultaneously.

Introduction

Congratulations and thank you for purchasing a Harvest Tec Model 335Z applicator. Please read this manual carefully to ensure the correct steps are taken to attach the applicator to the baler. This applicator is designed to apply Harvest Tec buffered propionic acid. Use of alternative products may cause complications. Including inaccurate readings from the flow meter and damage to all parts. Resulting in the warranty being void. A parts breakdown for the applicator is located in the back of the manual.

Made for iPad® running the current iOS operating system

• iPad is a trademark of Apple Inc., registered in the U.S. and other countries.
• Hay App version must be at least 2.7.1 (or higher) to operate with the iPad Integration Module (030-6672C)

Tools Needed

• Standard socket set
• Side cutter
• Crescent wrench
• Metal drilling and cutting tools
• Standard screwdriver or 5/16” nut driver
• Hose cutter
• Hammer
• Center Punch

Installation of Applicator

Installation of Mounting Brackets and Tank

1. Locate parts 001-4703ZR-A, 001-4703ZR-B, two 001-4703ZR-C and four ¾” x 4 ½” bolts, lock washers and nut.
2. Line up 001-4703ZR-A and 001-4703ZR-B about 18 inches apart on the ground. Slide part 001-4703ZR-C into square mounts and secure with ¾” x 4 ½” bolts, locks, and nuts to hold in place. Note there are two sets of ¾” holes on the 001-4703ZR-C. Use the set that is about 18 inches apart.
3. Locate part 001-4703ZR-D1 and two ½” x 5 ½” bolts, locks, washers, and nuts. Bolt part 001-4703ZR-D1 to the top of the two 001-4703ZR-C with this hardware.
4. Locate part 001-4703ZR-D2. Bolt to the front of 001-4703ZR-D1 with ½” x 3 ½” bolts, washers, locks, and nuts. Do not fully tighten down.
5. Using a lift, bring the assembly up under the cab of the baler. Part 001-4703ZR-D2 should line up with holes in the front part of the baler. Mark the half-inch holes at the ends of the 001-4703ZR-A and 001-4703ZR-B that line up with the structural parts under the cab. Lower assembly out of the way and drill these four holes with a 9/16” drill bit. (Note. Do not drill into hydraulic lines or electrical wires.
6. Once holes have been drilled. Lift assembly back up under cab and attach to baler with four ½” x 3 ½” bolts, washers on both sides, locks, and nuts. ¾” hardware is provided if you would want to use this. However, part 001-4703ZR-A and 001-4703ZR-B will need to be drilled out for the ¾” bolts. The 001-4703ZR-D2 will attach to the front mount with ½” x 2” bolts, washers on both sides, locks, and nut.
7. Attach two 001-4703ZR-E to each 001-4703ZR-C (one on each side) sticking out the front of the baler. Use ¾” x 4 ½” bolts, locks, and nuts. Do not fully tighten down yet.
8. Attach 001-4703ZR-G to the 001-4703ZR-E at the height you desire to keep the tank about the windrow. Note the lower the take the closer it is to the windrow coming into the baler. The higher it will obstruct your view. Use ¾” x 4 ½” bolts, locks, and nuts to secure.
9. Attach 001-4703ZR-G to 001-4703ZR-F with ½” x 4” Bolts, washers, locks, and nut. Do not fully tighten down. (Note: angles will be pointing toward each other.
10. Place saddle assembly on 001-4703ZR-G and secure with ½” washer, locks, and nuts.
11. Tighten all hardware down.

Installation of Mounting Brackets and Tank (continued)

Mount Pump Plate Assembly

• Locate parts bag 8. Using two 3/8” x 1/4” bolts, locks, washers, and nuts. Mount the U-shaped pump plate mount 001-4647 (right) onto the tank saddle in the mounting holes located between the strap brackets on back of the saddle (figure 7).
• Connect the pump plate mounting bracket (001-4648X), shown in figure 8, using two 3/8” x 1 1/4″ bolts, nuts, locks, and flat washers to the mounting bracket. Install the pump plate as shown in figure 9.

Placement of Spray Nozzle Assembly
The crossbar on the wind guard above the pick-up head provides a mounting point for the nozzle holders (001-4714J). Mount the nozzle holders on the wind guard, using the supplied U bolts (001-4714UBS). Measuring from the center of the baler, the nozzle holders will need to be 6” (15cm) apart on a 4’ (1.2M) and 9” (23cm) apart on a 5’ (1.5M) Do not fully tighten.
Position the nozzle holders so that the tips spray in a horizontal direction over the top of the baler’s pickup. The tips should be located so that they will be between 14” and 18” (35 – 45 cm) from the normal path of hay. Make sure the nozzle holders do not interfere with the tying system. *It is recommended to test the system with water before field operation. This will ensure the fan pattern from the tips reaches the outside edges of the pickup while having a slight overlap in the center.

Installation of Plumbing

A. Intake
Locate parts bag 16. Use the 003-EL3412 on the bottom of the tank to route 1/2″ line (002-9001) to the 003-A1212 or 003-EL1212 fitting used on the ball valve attached to the pump plate. Attach hose clamps (003-9003) on both of the fittings.
B. Discharge
Route the 1/2″ hose from the pump output toward the front of the baler and connect to the solenoid assembly (SOL-3SP-A). Secure the solenoid assembly and hose along baler, positioning the solenoid as close to the spray tips as possible. Connect the 1/4″ hose to the outgoing side of the solenoid to tip assembly.
C. Low, Standard and High Output Tips
Your baler comes with two sets of tips: a low set and a high set.

• Low set will cover outputs of 60 – 300 lbs/hr (27-300 L/hr).
• The standard set will cover outputs of 48- 448 lbs/hr (21-203 L/hr).
• High (optional) set will cover outputs of 80-800 lbs/hr (36L-363L).

Installation of Moisture Sensing Pads
*Most balers will have a moisture system already installed on the baler. If not, follow the instructions below. Note: If your baler does have a factory moisture system installed. You can use the factory moisture disc. However, you will need to disconnect the wires leading to both sensors and tape them up. You cannot have the baler’s moisture wires and Harvest Tec’s moisture wires connected to the moisture disc at the same time.

1. If your baler is equipped with bale shaping pads, remove disc and use the existing that will need to be drilled to 3/4″ (19mm) to install new moisture sensing discs. If the discs are welded, the welds will need to ground off for disc removal.
2. If your baler is not equipped with bale shaping pads you will need to drill a hole in the chamber directly behind and above the starting roll (Figure 1).
3. The mounting hole will be 3/4″ (19mm) in diameter. Use a plastic pad (006-4641F) and place it into the baler to use as a template. The bottom edge of the pad will be placed 1” (25mm) up from starting roll and 2” (51mm) from the back of the bale chamber. (Figure 1)
4. Depending on the baler the bolt may need to be trimmed for proper fit.
5. Tighten all of the hardware to 50 ft/lbs (68 N/m).
6. Make sure that the plastic pad protects all metal surfaces of the disc from touching the baler.
7. Run the moisture wire harness (006-4640G2) from the pump plate area to each disc and secure
8. Apply silicone over nuts and washers.

Installation of Bale Sensor

• The bale rate timer sensor is used to determine when the baler door is open. With this information, the system can change the tons/hour automatically (see Operating Instructions, Automatic Mode).
• Locate the sensor (006-7400) and the sensor bracket (001-4648RB). On the right side of the baler find a location 1”– 6” down from the hinge to mount the bracket. Check for clearance with hydraulic cylinders before mounting the bracket. The bracket should be mounted to the front side of the hinge point, with the sensor aligned over the back door.
• Mark and drill two 1/4” (7mm) holes and install the bracket using two 5/16” x1/4” self-tapping bolts.
• Install the sensor into the bracket and leave 1/4″ (7mm) of clearance between the end of the sensor and the door.
• The harness will need to be routed towards the Processor. Secure with cable ties and take care to avoid pinch points. The harness extension (006-7400EXT) may need to be used.

Additional parts and harness extensions have been included to allow you to easily disconnect the baler unit from the power unit, use as needed.

Installation of iPad Integration Control

• Locate a safe location in the cab of the tractor to place the iPad Integration Control (030-6672C). The recommended location is securely fastened out of the operator’s way in a location that is close enough to reach with the iPad cord.

• Connect the Power / Communication harness (006-6650TM(E)) to the bottom of the receiver.

• To operate the applicator, plug the iPad cord into the communication port indicated by:

iPad Integration Control Light Signals

• Green Slow Blink – Power is supplied to the applicator system and the unit is going through its startup process. This will take approximately 25-35 seconds.
• Green Double Blink – Indicating the iPad module recognizes the iPad but the app is not open or connected.
• Green Solid Light – The module is connected to the app and is ready to operate.
• Recommended to use the Lightning to USB-A cable included with the applicator kit (006-6672USBC) or the Optional USBC to USB-A cable (006-6672USBX). Use of plug adapters is not supported.
• Hay App version must be at least 2.7.1 (or higher) to operate with the iPad Integration Module (030-6672C)

Made for Apple iPad badge

Use of the Made for Apple iPad badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with an Apple product may affect wireless performance.

Wiring Diagram

1. Connect the power harness (006-3650T) to the tractor battery (12 volt) using the red wire with fuse to the positive side and the black wire to the negative.
   • The power harness must be connected to the battery! The unit will draw more amps than convenience outlets can handle. Any modifications of the power harness will void the system warranty. CONTACT HARVEST TEC BEFORE MODIFICATIONS.
   • This unit will not function on positive ground tractors.
   • If the unit loses power while operating it will not keep track of accumulated pounds of product used.
2. The power harness on the tractor (006-3650T) will run from the tractor battery to the hitch. The power harness on the baler (006-3650B1) will connect to the tractor power harness (006-3650T) at the hitch.
3. Connect the keyed power wire (006-5650K) to a keyed power source on the tractor. The keyed power wire must connect to a keyed source or the unit will not power up correctly.
4. Attached the iPad Integration Control (030-6672C) to the tractor power harness (006-3650T).
5. Attach the End of Bale (EOB) connection on the controller to the End of Baler Sensor (006-7400).
6. Attach the Solenoid (V1) (Delphi connector) connection on the controller to the wire from the solenoid (002-2203F). Note: If the solenoid is connected to a V2-DSM (not used) connection, the solenoid will not work.
7. Attach the Flowmeter (FLOW) connection on the controller to the flowmeter (006-4729A).
   • Attach the spade connectors on the FLOW harness to the Pump (007-4120DE).

System wiring diagram

Pin Outs
Power Tractor Harness 006-3650T at Hitch

• Pin 1 Red +12V Power to BLE
• Pin 2 Red +12V Power to THS
• Pin 3 Orange Keyed Power
• Pin 4 Not Used
• Pin 5 Green HT Can Low
• Pin 6 Yellow HT Can Hi
• Pin 7 Not Used
• Pin 8 Black Ground from BLE
• Pin 9 Black Ground from THS
• Pin 10 Not Used

Power Baler Harness 006-3650B1 at Hitch

• Pin 1 Red +12V Power to BLE
• Pin 2 Red +12V Power to THS
• Pin 3 Orange Keyed Power
• Pin 4 Not Used
• Pin 5 Green HT Can Low
• Pin 6 Yellow HT Can Hi
• Pin 7 Not Used
• Pin 8 Black Ground from BLE
• Pin 9 Black Ground from THS
• Pin 10 Not Used

iPad Integration Control / BLE Receiver on Tractor Harness 006-3650T

• Pin 1 Red +12V Power for BLE
• Pin 2 Black Ground for BLE
• Pin 3 Yellow HT Can Low
• Pin 4 Not Used
• Pin 5 Green HT Can Hi
• Pin 6 Not Used
• Pin 7 Not Used

End of Bale Sensor at 300 Controller Harness

• Pin 1 Brown Sensor Power
• Pin 2 Blue Sensor Ground
• Pin 3 N/A
• Pin 4 Black Signal from Sensor

Flow Meter at 300 Controller Harness

• Pin 1 White +5-12V Power
• Pin 2 Brown Ground
• Pin 3 Green Signal
• Pin 4 Not Used

End of Row Sensor at 300 Controller Harness

• Pin 1 Red/White +12V Power
• Pin 2 Black/White Ground
• Pin 3 Yellow Signal
• Pin 4 N/A

Moisture Sensor connection at 300 Controller Harness

• Pin 1 Not Used
• Pin 2 Not Used
• Pin 3 Not Used
• Pin 4 Not Used
• Pin 5 Not Used
• Pin 6 Not Used
• Pin 7 Not Used
• Pin 8 Blue Signal for Sensor 1
• Pin 9 Blue Signal for Sensor 2

Pump connection at 300 Controller Harness

• Pin 1 Red Power to Pump
• Pin 2 Black Ground to Pump

Solenoid Connection at 300 Controller Harness

• Pin A Black Solenoid Pause
• Pin B White Solenoid Ground

V2-DSM Connection at 300 Controller Harness

• Pin A Black Solenoid Pause
• Pin B White Solenoid Ground

Model 335Z Base Kit

Ref| Description| Part #| Qty| Ref| Description| Part #| Qty
---|---|---|---|---|---|---|---
1| 50 Gallon Tank| 005-9203SQ| 1| 7| Side Rail Plate| 001-4703ZR-E| 4
2| Tank Cap, Gasket, & Breather| P05-9022HBG| 1| 8| Front Mount Support| 001-4703ZR-D2| 1
3| Tank Saddle| 001-4703X| 1| 9| Front Mount Crossmember| 001-4703ZR-D1| 1
4| Tank Strap| 001-4402| 2| 10| Long Side Rail| 001-4703ZR-C| 2
5| Tank Saddle Support| 001-4703ZE-G| 2| 11| Mid-Mount| 001-4703ZR-B| 1
6| Short Side Rail| 001-4703ZR-F| 2| 12| Rear Mount| 001-4703ZR-A| 1
 |  |  |  | NP| Hex Plug| 003-F34| 1
 |  |  |  |  | Complete Kit| 030-0445Z-TK|

Model 335Z Base Kit (continued)

Ref| Description| Part #| Qty| Ref| Description| Part #| Qty
---|---|---|---|---|---|---|---
1| 50 Gallon Tank| 005-9203SQ| 1| 7| Side Rail Plate| 001-4703ZR-E| 4
2| Tank Cap, Gasket, & Breather| P05-9022HBG| 1| 8| Front Mount Support| 001-4703ZR-D2| 1
3| Tank Saddle| 001-4703X| 1| 9| Front Mount Crossmember| 001-4703ZR-D1| 1
4| Tank Strap| 001-4402| 2| 10| Long Side Rail| 001-4703ZR-C| 2
5| Tank Saddle Support| 001-4703ZE-G| 2| 11| Mid-Mount| 001-4703ZR-B| 1
6| Short Side Rail| 001-4703ZR-F| 2| 12| Rear Mount| 001-4703ZR-A| 1
 |  |  |  | NP| Hex Plug| 003-F34| 1
 |  |  |  |  | Complete Kit| 030-0445Z-TK|

Parts Breakdown for Pump Assembly

Part#| Description| Qty| Part#| Description| Qty
---|---|---|---|---|---
003-EL3812| 3/8”MPT X 1/2″HB Elbow| 1| 003-M1212| 1/2″ Union| 2
007-4120DE| 300 Series Pump| 1| 002-4315-100| 1/2″ Line Strainer-100 Mesh| 1
003-M3838| 3/8” x 3/8” Union| 1| 003-SE12| 1/2″ Street Elbow| 1
003-SE38| 3/8” Street Elbow| 1| 002-2212| 1/2″ Ball Valve| 1
002-4566F| 3/8” Check Valve| 1| 003-EL1212| 1/2″MPT x 1/2″HB| 1
003-RB3814PB| RB 3/8” x 1/4” Reducer| 1| 001-4648XL| 300 Pump Support| 1
006-4729A| Flow Meter – Block Style| 1| 001-4648X| Pump Plate Mount| 1
003-RB1214PB| RB 1/2″ x 1/4″ Reducer| 1| 003-A1212| Not Pictured|
003-M1212F| 1/2″ Coupler| 1| 003-A3812| Not Pictured|
 |  |  | Pump Assembly PMP-3636P (001-4647 Not Included)

Completed Assembly

Note: Due to alternative baler designs, elbow 003-EL3812 can be replaced by straight fitting 003-A3812. As well as elbow 003-EL1212 can be replaced by straight fitting 003-A1212. Both straight fittings are included.

300 Solenoid Packages

Solenoid Package A

Ref| Description| Part #| Qty| Ref| Description| Part #| Qty
---|---|---|---|---|---|---|---
1| Solenoid Harness (5’)| 006-3650-S2| 1| 6| 1/4″ Female Disconnect| 004-1207H| 2
2| #6 Hose Clamp| 003-9003| 1| 7| Solenoid| 002-2203F| 1
3| 1/4″ x 1/2″ Straight Fitting| 003-A1412| 1| 8| Solenoid Valve Body| 004-1207VF| 1
4| 1/4″ Female Connector| 004-1207G| 1| 9| 1/4″ x 1/4″ Straight Fitting| 003-A1414| 1
5| Rubber Washer| 004-1207W| 2| 10| Mini Hose Clamp| 003-9002| 1
 |  |  |  |  | Complete Assembly| SOL-3SP-A|

Moisture Sensors

Ref| Description| Part #| Qty| Ref| Description| Part #| Qty
---|---|---|---|---|---|---|---
1| Plastic Pad| 006-4641F| 2| 4| Plastic Isolator| 006-4641I| 2
2| Moisture Disc| 006-4641H| 2| 5| 1/2X4 1/2” Carriage Bolt| Hardware| 2
3| Plastic Bushing| 006-4641G| 2| 6| Moisture Cable| 006-4640G2| 1
 |  |  |  | Moisture Pad Assembly (Ref 1-5)| 030-4643| 2
 |  |  |  | Complete Assembly (Ref 1-6)| MSH-RB-A|

Control Box and Wiring Harnesses

End of Bale Sensor Kit A

Parts Bag Packages

Hoses

(Tank to Solenoid)

| 002-9001| 15ft

12

| 3/4″ Hose (Drain/Fill Line)|

002-9002

|

6ft

13| 1/4″ Hose| 002-9016| 6ft
 | (Solenoid to Tips)|  |

335Z Spray Shield

Ref| Description| Part #| Qty| Ref| Description| Part #| Qty
---|---|---|---|---|---|---|---
1| U bolt| 001-4714UBS| 4| 10| Nozzle Body| 004-4722| 2
2| Hose clamp| 003-9002| 2| 11| Tip Strainer| 004-1203-100| 2
3| 1/4″ x 1/4″ Fitting| 003-A1414| 5| 12| Tip – White| 004-XR11008VS| 2
4| 1/4″ Sq Tee| 003-TT14SQ| 1| 13| Tip – Red| 004-XR11004VS| 2
5| 1/4″ St Elbow| 003-SE14F| 1| 14| Nozzle Cap| 004-4723| 2
6| Oetiker Clamp| 003-9008| 4| NP| 477 Jiffy Clip| 008-9014| 2
7| Nozzle Holder| 001-4714J| 2|  |  |
8| Hose| 002-9016| 3ft|  | * Tip color subject to change|
9| 1/4″ x 1/4″ Fitting| 003-A1414F| 2|  |  |
 |  |  |  | Spray Shield Only| 030-4714J-SO|

Optional iPad Display Kit

Ref| Description| Part #| Qty|  |
---|---|---|---|---|---
1| iPad Mini 4 (Refurbished)| 006-4670IP| 1| Complete iPad Mini Kit| 030-4670DK
2| Suction Cup Mount| 001-2012SCM| 1| (Includes 1-5 and Comm. Cable)
3| Ram Mount| 001-2012H| 1|  |
4| Spring Load Cradle| 001-2012SLC| 1| Mounting Kit Only| 030-2014MK
5| iPad Mini 4 Case| 001-2012C4| 1| (Includes all parts except iPad Mini 4)
NP| Lightning Comm. Cable| 006-6672USBC| 1|
6| Power Harness| 006-4723P| 1|
NP| 4 amp Fuse| Hardware| 1|
7| Female Spade Connector| Hardware| 2|
8| Eye Loop Connector| Hardware| 2|
9| iPad Mini Charger 12V| 001-2012P| 1|

12V Power Harness Installation Instructions (included with Mounting Kit Only)

1. Identify 12V power source for wires to connect.
2. Eye loops are installed on the harness if wiring directly to the battery is desired.
3. Test for key power source if preferred to have power to the USB shut off with the key.
4. Once the power source is identified, cut wires to the desired length if needed for key power connection.
5. Harness comes with quick connectors the white and black wires.
6. Remove the round locking plastic nut from USB plug before connecting the wires. Black (+) White (-).
7. The wires will then be hooked to the designated terminals on the bottom of the USB plug
8. Drill a 1 1/8” hole in the preferred mounting location. Be sure to clean any sharp edges after drilling.
9. Feed the wires through the mounting hole.
10. If using the round plastic nut to secure plug in place, slide the nut back over the wiring before connecting the wires to a powered source.
11. Connect the wires to the identified power source if easier to do so before tightening the plug into place.
12. Tighten plug using either the round plastic nut or mounting plate and two screws, both options supplied.
13. Once connected, hook a USB charging cord into the plug and connect a mobile device/tablet to ensure the plug is operating as you wish (key power working properly if necessary).

NOTE: This plug is not designed to charge two iPads. System damage could occur if this is attempted. The system will charge a mobile phone and iPad simultaneously without a problem.
iPad mini is a trademark of Apple Inc., registered in the U.S. and other countries.

Warranty

Harvest Tec LLC. Warranty and Liability Agreement

Harvest Tec, LLC. will repair or replace components that are found to be defective within 12 months from the date of manufacture. Under no circumstances does this warranty cover any components which in the opinion of Harvest Tec, LLC. have been subjected to negligent use, misuse, alteration, accident, or if repairs have been made with parts other than those manufactured and obtainable from Harvest Tec, LLC. Our obligation under this warranty is limited to repairing or replacing free of charge to the original purchaser any part that in our judgment shows evidence of defective or improper workmanship, provided the part is returned to Harvest Tec, LLC. within 30 days of the failure. If it is determined that a non-Harvest Tec branded hay preservative has been used inside the Harvest Tec applicator system where the failure occurred, then Harvest Tec reserves the right to deny the warranty request at their discretion. Parts must be returned through the selling dealer and distributor, and transportation charges prepaid. This warranty shall not be interpreted to render Harvest Tec, LLC. liable for injury or damages of any kind, direct, consequential, or contingent, to persons or property. Furthermore, this warranty does not extend to loss of crop, losses caused by delays or any expense prospective profits or for any other reason. Harvest Tec, LLC. shall not be liable for any recovery greater in amount than the cost or repair of defects in workmanship. There are no warranties, either expressed or implied, of merchantability or fitness for a particular purpose intended or fitness for any other reason. This warranty cannot guarantee that existing conditions beyond the control of Harvest Tec, LLC. will not affect our ability to obtain materials or manufacture necessary replacement parts. Harvest Tec, LLC. reserves the right to make design changes, improve design, or change specifications, at any time without any contingent obligation to purchasers of machines and parts previously sold.

CONTACT

HARVEST TEC, LLC.

• P.O. BOX 63
• 2821 HARVEY STREET
• HUDSON, WI 54016 USA
• PHONE: 715-386-9100
• FAX: 715-381-1792
• Email: info@harvesttec.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>