mollie A12-FL-003-SG Tower Fan with Remote Control Instruction Manual

mollie A12-FL-003-SG Tower Fan with Remote Control Instruction Manual

PLEASE READ THESE INSTRUCTIONS BEFORE USE AND RETAIN THEM FOR FUTURE REFERENCE.

PRECAUTIONS AND SAFEGUARDS

• Use this electrical appliance as described in this manual. Any other use is not recommended by the manufacturer and could have a detrimental effect on the durability of the appliance and or the safety of the user.
• Please inspect the unit for damage after unpacking.
• To reduce the risk of electric shock, do not remove the cover. No user serviceable parts inside.
• Before you connect the appliance, ensure the voltage rating on the rating label corresponds to your mains voltage.
• Repairs should only be performed by qualified personnel. Improper repairs may place the user and/or equipment at serious risk.
• Do not operate this appliance with a damaged plug, or cord, after a malfunction, or after being dropped or damaged in any way.
• Never leave this appliance unattended whilst in use.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified people in order to avoid a hazard.
• Do not insert or allow foreign objects or metal utensils into any ventilation or exhaust openings as this may cause an electric shock, fire or damage to the appliance.
• If abnormal noise, smell, smoke or any other failure is discovered during operation, turn off the product and unplug the power plug. Then contact the service centre for repair.
• Do not remove the appliance from the mains power supply by pulling the cord, pull the plug instead.
• This appliance is not intended for the use by people (including children) with reduced physical, sensory or mental capabilities or a lack of experience or knowledge. They should be given appropriate supervision and instructions to use the equipment by a person responsible for their safety.
• Make sure that infants or elderly people are not directly exposed to the fan.
• Never leave the device within the reach of children. Close supervision is required when using this device near children.
• Do not use this device for anything other than its intended use.
• Do not immerse the product in water or any other liquid. Do not use the appliance with wet hands, on a damp floor or when the appliance itself is wet.
• Always unplug the appliance after use and before any cleaning or user maintenance.
• Ensure the equipment is not too close to heat emitting appliances or placed in direct sunlight.
• Never use harsh or abrasive cleaning fluids on the device.
• The device must not be used in potentially dangerous locations such as flammable, explosive, or wet atmospheres where petrol, flammable liquids, or other chemicals are used or stored.
• This product is designed for domestic use only. It is not intended for heavy duty, commercial or industrial use, and is not suitable for outdoors.
• Always place the device on a stable, at level surface when operating, to avoid the possibility of tipping over.
• Do not cover the appliance.
• Unroll the cord before operating. Operating with a coiled cord may cause overheating and risk of fire.
• The use of an extension cord with this appliance is not recommended.
• Make sure that the cord is placed in a way that it doesn’t pose a risk to anyone.
• Always disconnect the product from the power supply when moving it from one location to another.
• Avoid extreme degrees of temperature, either hot or cold. Place the device well away from heat sources such as radiators, or gas/electric fires.
• Always store the appliance in a dry location.
• The warnings and precautions in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator, that common sense and caution are factors, which cannot be built into this product, but must be supplied by the operator.

ASSEMBLY

1. Always unplug the device before assembling it.
   
   Note: The fan should only be used when it is assembled.

2. Connect the two base parts and place the fan body on top of them. There are 2 pillars on the fan body that need to be inserted into the 2 holes in the base.

3. Attach the fan body onto the base and secure it with the supplied 4 screws.

OPERATION

ON/OFF: Press this button on the control panel or on the remote control to turn the unit on.
The LED screen will show the room temperature. The fan will start at low speed and normal mode. Press the button again to turn the device off.

Speed: Press this button to change the speed level of the wind.
The 3 levels are low (2 bars), medium (4 bars), and high (6 bars). Each time this button is pressed, the amount of the horizontal bars will change on the LED screen indicating the current speed level.

Mode: Press this button to choose the wind setting.
Each time this button is pressed, the LED screen will indicate the current wind setting. There are 3 different wind settings: Normal, Natural (tree icon), and Sleep (sleeping smiley icon).

• Normal: A continuous wind blow, that can be used in all 3 speed settings.
• Natural: Designed to replicate natural and varying wind speeds, the speed button is disabled in this mode. The speed levels will alternate from: low, medium, high, medium, low, medium, high, medium, low, medium, high, and medium.
• Sleep: This setting was designed to use the effects of the natural wind mode to fall asleep. It will gradually decrease the speed of the fan:
  – With the low speed setting: The fan will run the same as in low speed natural wind mode.
  – With the medium speed setting: The fan will spend 30 minutes at the medium natural wind mode and then switch to low speed.
  – With the high speed setting: The fan will spend 30 minutes in the high speed setting, 30 minutes in the medium speed setting and then switch to the low speed setting.

Timer: Press this button (clock icon) to set the fan running time. The timer can be set from 1 to 12 hours. Each time the button is pressed you add another hour to the timer. The LED screen will indicate the current timer setting when you press this button. To cancel the timer just press this button until the LED screen shows 00.
OSC: Press this button to let the device oscillate horizontally. Press the button again to stop the oscillation.
Light: Press this button to turn on the light. Press the button again to turn it off

REMOTE

The remote control operates with a CR2025 (3V) Lithium battery. Direct the remote in the direction of the control panel of the fan to use it. If the remote doesn’t work, replace the battery.

CLEANING AND CARE

It is recommended to clean your fan regularly. Please follow the steps below to clean your device.
WARNING! Always turn the unit off and unplug the power cord before cleaning.

• Always remove the plug from the socket-outlet, and allow the fan to stop completely before cleaning it.
• Clean the exterior case of the fan with a soft damp cloth.
• Clean the control panel only with a dry cloth, never with water.
• Never use abrasive cleaning agents or sharp objects for cleaning.
• Make sure the unit is completely dry before plugging it back into the power supply.
• Do not allow water to drip on, or enter the fan housing.
• Use a vacuum cleaner to clean the dust from the fan blades.
• The air outlet filter can be detached to clean. Wash the filter under running water and then dry it completely. After cleaning, spin the 2 screws back to secure it in position.
• Do not attempt to remove the fan blades.
• Do not allow the motor, or other electrical components to be exposed to water.
• When storing your fan in the off-season, it is important to keep it in a safe, dry location. It is important to protect the fan from any dust. We recommend using the original box, when storing the product away.
• When the remote control is not in use for a longer time, take out the battery to prevent damage, due to battery leakage

TECHNICAL SPECIFICATION

Power Supply: 110 V, 50 Hz
General Power: 50 W
Battery for remote: CR2025 (3V) Lithium Battery

INFORMATION IN WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL AND ELECTRONIC EQUIPMENT

This mark on a product and/or accompanying documents indicates that when it is to be disposed of; it must be treated as Waste Electrical and Electronic Equipment (WEEE)
Any WEEE marked waste products must not be used with general household waste, but kept separate for the treatment, recovery and recycling of the materials used.
For proper treatment, recovery and recycling; please take all WEEE marked waste to your Local Authority Civic waste site, where it will be accepted free of charge.
If all consumers dispose of Waste Electrical and Electronic Equipment correctly, they will be helping to save valuable resources and preventing any potential negative effects upon human health and the environment, of any hazardous materials that the waste may contain.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>