SAM S POL-1-01 Polaris Sportsman Reverse Light Kit Installation Guide

August 26, 2024
SAM S

SAM S POL-1-01 Polaris Sportsman Reverse Light Kit

SAM S-POL-1-01-Polaris-Sportsman-Reverse-Light-Kit-
Product

Product Information

Specifications

Product Usage Instructions

Step 1: Remove Plastics

  1. Remove the center plastic in the cargo compartment to access the bus bar using the T-25 Torx bit.
  2. Remove the clutch side panel (two plastic rivets).

Step 2: Connect Diagnostic Connector & Power Leads

  1. Remove the diagnostic connector cover and plug the integrated connector into the reverse light wiring harness.
  2. Connect positive leads to the positive terminal of the bus bar and negative leads to the negative terminal.

Step 3: Mount Controller, Relay, & Fuse
Secure controller, relay, and fuse. Use the drilling template provided and tighten components with machine screws.

Step 4: Mount Light

  1. Attach the light to its bracket. Slide the bolt through the bracket before attaching it to the light. Attach light bracket to mounting bracket.
  2. Remove the nut on the right side and fix the left side with the provided 1-1/2 bolt.

Step 5: Route Power to Light

  1. Run wire and connector along the stock wiring harness back to the reverse light, securing with zip ties as needed.
  2. Plug in the reverse light.

Step 6: Reinstall Plastics

Operation of Reverse Lights

  • Our controllers have a manual override feature. Back-up lights can be turned on without the vehicle in reverse.
  • To turn the light off, repeat the procedure. Note that if the ignition is turned off while the vehicle is in reverse or the manual override function is enabled, the lights will remain on until the ECU enters sleep mode (approximately 30 seconds – 2 minutes).

FAQ

Q: What should I do if the lights do not turn on?
A: Check the connections and ensure proper installation following the provided instructions. Verify the power source and troubleshoot any issues with a multimeter if needed.

Read the entire manual before beginning the installation process.

Disclaimer:
Sam’s Backup Lights is not responsible for any damage due to improper installation.

Parts

SAM S-POL-1-01-Polaris-Sportsman-Reverse-Light-Kit-Fig-
\(1\)

What’s Included

Description Quantity
Wiring Harness 1
Relay 1
Bracket & Hardware 1
Mounting Bolts & Nuts 3
Light 1
Zip Ties 6

Required tools

Torx T-25 Bit

10mm Socket
Phillips Screwdriver
13/64” Drill Bit (optional)
1/2“ Deep-Well Socket
1/2“ Combination Wrench
Wire Cutter (trimming zip ties)

Installation Instruction

Step 1: Remove Plastics

  1. Remove the center plastic in the cargo compartment to access the bus bar using the T-25 Torx bit.
  2. Remove the clutch side panel (two plastic rivets).

SAM S-POL-1-01-Polaris-Sportsman-Reverse-Light-Kit-Fig-
\(2\)

Step 2: Connect Diagnostic Connector & Power Leads

  • Remove the diagnostic connector cover and plug the integrated connector into the reverse light wiring harness.
  • Connect positive leads to the positive terminal of the bus bar and negative leads to the negative terminal.

SAM S-POL-1-01-Polaris-Sportsman-Reverse-Light-Kit-Fig-
\(3\)

Step 3: Mount Controller, Relay, & Fuse
Secure controller, relay, and fuse. The suggested method is to use a drilling template and tighten components with provided machine screws.

SAM S-POL-1-01-Polaris-Sportsman-Reverse-Light-Kit-Fig-
\(4\)

Step 4: Mount Light

  1. Attach the light to its bracket. Be sure to slide the bolt through the bracket before attaching it to the light. Attach light bracket to mounting bracket.
  2. Remove the nut on the right side and fix the left side with the provided 1-1/2” bolt.SAM S-POL-1-01-Polaris-Sportsman-Reverse-Light-Kit-Fig- \(5\)

Step 5: Route Power to Light

  1. Run wire and connector along stock wiring harness back to reverse light, while zip-tying the wire as needed.
  2. Plug in the reverse light.

SAM S-POL-1-01-Polaris-Sportsman-Reverse-Light-Kit-Fig-
\(6\)

Step 6: Reinstall Plastics

SAM S-POL-1-01-Polaris-Sportsman-Reverse-Light-Kit-Fig-
\(7\)

Operation of Reverse Lights

Our controllers have been programmed with a manual override feature. Back-up lights may be turned on without the vehicle in reverse.

  • Fully Automatic When Shifted to Reverse
    1. No programming needed
  • Manual Override Function
    1. Shift the vehicle into neutral
    2. Press the reverse override button once. The reverse light will turn on and remain on.

To turn the light off repeat this procedure.

Note:
If the ignition is turned off while the vehicle is in reverse, or the manual override function is enabled, the lights will remain ON until the ECU enters sleep mode (approximately 30 seconds – 2 minutes depending on vehicle and ECU type).

Contact Information

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals