ELEGANT SHOWERS 600 mm Round Bathroom Mirror with LED Lights Installation Guide
- June 16, 2024
- ELEGANT SHOWERS
Table of Contents
ELEGANT SHOWERS 600 mm Round Bathroom Mirror with LED Lights
Product Information
Specifications
- Type : IP44 Illuminated Mirrors
- Installation: Requires a qualified electrician
- Installation Area: Zone 2
- Power Supply: Must be switched off before installation, maintenance, or cleaning
- Earthed: Mirror must be earthed
- Distance from Basin: Install the mirror at least 15cm away from the basin
Product Usage Instructions
Installation Instructions
- Before starting the installation, disconnect the power supply cable at the main fuse box.
- Thoroughly check the entire space to verify that there are no hidden cables or pipes in the intended installation area.
- Mount the mirror on the wall using two fixing screws.
- Ensure that the mirror is at the correct height and level. Use a suitable marker to mark the hole positions on the wall through the fixing holes.
- Drill holes in the marked locations using the appropriate size drill bit for the wall fixing.
Cleaning Guidelines
To preserve the high-quality finish of this product, refrain from using
abrasives or solvents during the cleaning process. Use a damp cloth
exclusively for cleaning, ensuring that no water is left standing on any part
of the mirror. Promptly clean any spills that could impact the finish quality
as previously described.
Handle with Caution
Exercise care when cleaning this product. While its finish is highly
durable, it may sustain damage from abrasive cleaners and cleaning pads. Use a
mild, non-abrasive cleaning solution or polish for cleaning.
FAQ
-
Q: Can I install the mirror myself?
A: No, the mirror must be installed by a qualified electrician. -
Q: How far should the mirror be installed from the basin?
A: The mirror should be installed at least 15cm away from the basin. -
Q: Can I use abrasive cleaners to clean the mirror?
A: No, refrain from using abrasives or solvents during the cleaning process. Use a mild, non-abrasive cleaning solution or polish.
INSTALLATION INSTRUCTIONS FOR IP44 ILLUMINATED MIRRORS
Prior to installing this product, carefully follow these instructions. The luminaire must be installed by a qualified electrician in accordance with the wiring standards in force in the country where the installation takes place. These products can be safely installed in Zone 2. Refer to the lighting regulations diagram for further guidance.
Warning:
- The power supply must be switched off before installation, maintenance or cleaning. Remove the fuse or de-activate it, and make sure that it cannot be re-activated
- The mirror must be earthed
- Install the mirror at least 15cm. away from the basin
- Before drilling a hole, make sure that there is no risk of drilling through an existing non-visible cable or pipe
Installation Instructions
- Before starting the installation, disconnect the power supply cable at the main fuse box.
- Verify that there are no hidden cables or pipes in the intended installation area by thoroughly checking the entire space.
- Mount the mirror on the wall using two fixing screws.
- Ensure that the mirror is at the correct height and level. Use a suitable marker to mark the hole positions on the wall through the fixing holes.
- Drill holes in the marked locations using the appropriate size drill bit for the wall fixing. Note that for certain wall types, such as plasterboard walls, the supplied wall fixings are not recommended.
- Insert raw plugs into the holes, feed the supply through the central rubber grommet, position the back plate, and secure it using the correct fixings. Use rubber washers provided to prevent water penetration into the fitting.
- Connect the supply cable to the connector block following the wiring diagram. Ensure that the conductors are fully inserted into the terminals with no loose wire strands protruding. Tighten the screws on the terminals securely, ensuring they clamp onto the conductor and not the insulation.
- Attach the mirror to the wall.
- Always use the correct type and wattage bulb (refer to Luminaire for details).
- Switch on the power, and then test the product by touching the switch sign with a finger on the sensor below the sensor.
Cleaning Guidelines
To preserve the high-quality finish of this product, refrain from using abrasives or solvents during the cleaning process. Use a damp cloth exclusively for cleaning, ensuring that no water is left standing on any part of the mirror. Promptly clean any spills that could impact the finish quality as previously described
Handle with caution:
Exercise care when cleaning this product. While its finish is highly durable,
it may sustain damage from abrasive cleaners and cleaning pads. Use a mild,
non-abrasive cleaning solution or polish for cleaning
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>