SAM S CAN Series Defender Reverse Light Kit Installation Guide

SAM S CAN Series Defender Reverse Light Kit

Product Information

Specifications

• Product Name: CAN-AM Defender Reverse Light Kit
• Included Components:
  • Wiring Harness – 1
  • Jumper Wire – 1
  • Relay – 1
  • Zip Ties – 8
  • Controller – 2
  • Mounting Screws
• Required Tools:
  • 13mm Socket & Ratchet
  • 13mm Wrench
  • Philips Screwdriver
  • Flat Head Screwdriver
  • Torx T-40
  • 1/16 and 5/16 Drill Bit
  • Wire Cutter (for trimming zip ties)

Frequently Asked Questions

Q: What should I do if I encounter issues with connecting wires?

A: If you face difficulties with wire connections, refer back to the manual and ensure each step is followed accurately. If problems persist, contact our support team at support@samsbackuplights.com for assistance.

Q: Can I install this reverse light kit on a different vehicle model?

A: The CAN-AM Defender Reverse Light Kit is specifically designed for use with CAN-AM Defender models. Installing it on other vehicles may require modifications and could void any warranties.

CAN-AM Defender Reverse Light Kit

Included

Required Tools

13mm Socket & Ratchet

13mm Wrench
Philips Screwdriver
Flat Head Screwdriver
Torx T-40
1/16” and 5/16” Drill Bit
Wire Cutter (trimming zip ties)

Read entire manual before beginning the installation process.

Disclaimer: Sam’s Backup Lights is not responsible for any damage due to improper installation.

INSTALLATION INSTRUCTION

Step 1: Secure and Plug-in Controller

1. Remove diagnostic connector and plug connector into controller.
2. Secure controller with provided mounting screws; if necessary, drill 1/16” pilot hole.
3. Connect bullet connector to the factory solid white wire under the hood.
   Note: If preexisting wires are not available or already in use refer to step 2b

Step 2a: Routing Wires Under Dash & Floor

1. Under the center of the dash, 4 factory wires will be visible.
2. Plug the 4-inch blue wire into the solid white wire, and then into the solid blue wire.
3. Remove the Floorboard by removing the three push rivets and pulling up.
4. Connect the Light Blue wire coming out of the relay to the Solid Blue wire under the previously removed floorboard.

Step 2b: Routing Wires Under Dash & Floor

1. Plug the jumper wire provided in the kit into the Light Blue wire from the controller.
2. Route the jumper wire through the firewall. Remove the winch-control outlet to gain access – there is a rubber seal that runs across the frame, sealing the cab.
3. Connect the jumper wire to the Light Blue wire coming out of the relay.

Step 3: Assemble Connector

This step applies to enclosed cab kits only.

1. Assemble the connector by pushing the red wire into the hole marked 1 and the black into hole 2. Push the wires in until they click into place and lock into the connector.
2. Push the green wedge lock in until it clicks.
3. Plug the connector into the light and secure the wire using zip ties.

Step 4: Route LED Light Harness

1. Remove the plastic cover near the lower door hinge.
2. Run wires (ring terminal and relay terminal ends) from inside the cab down the inside of rear passenger pillar; retrieve wires from the hole right below the lower door hinge.
3. Route wire up to the battery.

Step 5: Attach Power Leads and Relay

1. Attach black ring terminal to negative battery terminal.
2. Plug remaining red relay terminal into relay housing; insert relay into housing. Push in until it clicks.
3. Attach red ring terminal to positive battery terminal.
4. Secure fuse and relay using zip ties.

Auxiliary Output Option #1

1. Under the hood, Plug in yellow bullet connector from the control box into the factory green & white wire.
2. Plug the yellow 4-inch wire into blue & brown wire and Green & White wire under the dash.
3. Plug in the yellow 25-inch wire off the relay into the blue & brown wire under the floorboard.
4. Secure relay & fuse under seat.
5. Connect the red wire to the positive side on the battery. Add in wire from the connector off the relay to the 12v accessory.

Auxiliary Output Option #2 Front Light Bar Power

Factory Can-Am Diagnostic Connector

The Orange wire from Sam’s Controller needs to match the Orange/Green wire on the factory Can-Am diagnostic connector

Operation of Reverse Lights
Sam’s Backup Lights are automatic. NO switches or programming required. When the vehicle is shifted into reverse, the lights will automatically come on. The controller has been programmed with a manual override feature, so back-up lights can be turned on without the vehicle needing to be shifted into reverse.

Fully Automatic When Shifted to Reverse
No programming needed

Manual Override Function

1. Shift the vehicle into Neutral
2. Press and hold the brake pedal for up to 2 seconds. The reverse light will automatically turn on and stay on.

• To turn the light off repeat this procedure.

Operation of Auxiliary Output Option

Manual Override Function
Auxiliary output is turned ON by pressing the TRIP button two times within 1 second while in Park, Neutral, High, or Low gear
*To turn the accessory off repeat this procedure.

Note: If the ignition is turned off while the vehicle is in reverse, or the manual override function is enabled, the lights will remain ON until the ECU enters sleep mode (approximately 30 secs to 2 minutes depending on vehicle and ECU type).

Sam’s Backup Lights
www.samsbackuplights.com

CAN-AM Defender Reverse Light
support@samsbackuplights.com

References

• Sam's Backup Lights

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>