RUPT 2BC3D BOOMZ Wireless Speaker User Manual

RUPT 2BC3D BOOMZ Wireless Speaker

What’s in the box

• Speaker with hook 1pc
• USB cable 1pc
• User manual 1pc

Key Functions

• BT button
• Rotary knob
• LED light

LED light

• Paring: blue light fast flash
• Paired: blue light on
• Tws on: Blue light slow flash
• Charging: red light on
• Fully charged: red light on

Rotary knob

• Power on/off: hold 2s
• Play/pause: one click
• Next track: 2 click
• Previous track: 3 click
• Volume+: clockwise rotation
• Volume-: counterclockwise rotation
• Answer/end call: single click
• Reject calls: hold 2s

BT button

• Paring mold: hold 2s
• Siri: 2 click
• Tws on/off: 3 click

Notes:

1. Charging with DC5V/1A adaptor or USB Cable
2. While max/minimum volume, you can hear a prompt tone

Bluetooth Connection

1. Turn on the speaker, you will hear the boot
2. After opening the phone’s Bluetooth, Click the “Boomz” to pairing

Notes:

1. If it is not paired for 15 minutes after booting, it will shut down. When low battery, you can hear the prompt tone then the speaker will power off automatically.
2. If Apple users feel that the volume is low, they can turn off this setting on the phone(Settings-Sounds & Haptics-Headphone Safety-Reduce Loud Sounds).

Specifications

Built-in Microphone

Safety Instructions

1. Keep the product away from extremely hot and cold environments, it will damage the battery and circuit.
2. Avoid liquid immersion into the product.
3. Do not disassemble the product.
4. Do not use concentrated chemical products or detergents to clean the product.
5. Use only 5V/1A power supply. Connecting the power supply voltage too high may cause serious damage.
6. Do not randomly discard or place the product near fire or high temperature to avoid the danger of explosion.

FCC

FCC statement

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

FAQs

• Q: How do I know when the speaker is fully charged?
  • A: When charging, a red light will be on. Once fully charged, the red light will turn off.
• Q: What should I do if the Bluetooth pairing fails?
  • A: Make sure the speaker is in pairing mode (blue light fast flash) and try again. You can also check if there are any other devices connected to the speaker.
• Q: Can I use this speaker for hands-free calling?
  • A: Yes, you can answer and end calls with a single click on the speaker.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>