RUPT 2BC3D Echodeep Wireless Headphones User Manual

RUPT 2BC3D Echodeep Wireless Headphones

Specifications

• Product Type: Wireless Headphones
• Dimensions: 18519085mm
• Weight: 227g
• Driver: 40mm
• Audio Playtime: Approx 20 hours (@50-60% Volume)
• Bluetooth Version: V5.3
• Rated Power: 64 40mW
• Power Supply: Built-in 3.7V 300mAh Lithium Battery
• Charging Time: Approx 2.5 hours (USB C)
• Frequency Response Range: 100-20KHZ
• Input Power: DC 5V/1A
• Microphone: Built-in

Product Usage Instructions
Turn On the Headphones
Turn on the headphone by pressing the power button until you hear the boot sound.s.

FAQ
Q: How should I charge the headphones?
A: Charge the headphones using a DC5V/1A adaptor or USB cable.

What’s in the box

Key functions

Button Function

NOTE:Press gestures and touching the correct area will offer you a fluent experience

• Click + area(refer to product Diagram) to Volume up.

• Click – area(refer to product Diagram) to Volume down.

• Click the Previous track area to change the channel, and long press to fast-back.
  Click the Play area to play/pause, and long press to power on/off Double click for voice assistant

• Click to answer when an incoming call and click to end it. Hold 2s to reject the call.

• Click the next track area to change the channel, and long press to fast-forward.

Troubleshooting

• No power
  • Recharge your wireless Bluetooth headphones using the Type-C cable.
• Music is not playing over Bluetooth
  • Make sure your Bluetooth device has an A2DP profile. Check if both devices are paired and connected over Bluetooth. Restart the headphones to reconnect your Bluetooth device.
• Bluetooth device will not reconnect with the headphone
  • Navigate to your Bluetooth settings menu on your Bluetooth device, tap “Echodeep”, and select “Forget” .
  • Now follow the steps to pair your device again. Or, press & hold the power button on the headphones (while powered on) to disconnect the headphones from any connected devices. Then follow the steps to reconnect your device.

Charge It

• On the right earcup, carefully plug the Type-C cable into Type-C charging port. and connect the other end of the cable to either a computer USB port or to a USB-compatible car or wall charger.
• A solid red LED light will appear to indicate when the headphone is charging.
• When charging is complete, the LED light will turn Blue.
• Charging time is approximately 2 hours.

LED display

Paring: blue light fast flash Paired: blue light off Charging: red light on Fully charged: Blue light on

Notes :

1. Charging with DC5V/1A adaptor or USB Cable
2. While max/minimum volume,you can hear a prompt tone

Bluetooth Connection

1. Turn on the headphones, you will hear the boot
2. After open the phone’s Bluetooth, Click the “Echodeep” to pairing

Notes

1. If it is not paired for 5 minutes after booting, it will shut dowm. When low battery,you can hear the prompt tone then the headphone will power off automatically
2. If Apple users feel that the volume is low, you can turn off this setting on the phone(Settings-Sounds & Haptics-Headphone Safety-Reduce Loud Sounds)

Specificaons

Safety Instructions

1. Keep the product away from extremely hot and cold environments, it will damage the battery and circuit.
2. Avoid liquid immersion into the product.
3. Do not disassemble the product.
4.  Do not use concentrated chemical products or detergents to clean the product.
5.  Use only 5V/1A power supply. Connecting the power supply voltage too high may cause serious damage.
6. Do not randomly discard or place the product near fire or high temperature to avoid the danger of explosion.

FCC statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>