KitchenBrothers KB4065 Kettle With Temperature Control User Manual

KitchenBrothers KB4065 Kettle With Temperature Control

Product Usage Instructions

Introduction
Thank you for choosing a KitchenBrothers product! Always follow the safety instructions for safe use.

Intended Use
A kettle is solely intended for heating or boiling water. It is not meant for heating other liquids. A kettle heats water using an electric heating element. The supplier is exempt from liability for any injury or damage caused by using the product outside its intended use. Any modification to the product may affect your safety and warranty.

Product Overview
The product includes:

1. Lid with button
2. Spout
3. Water level and LED indicator
4. Base with power connection
5. Display
6. +/- button
7. On/Off button

Safety
Detailed safety instructions go here.

FAQ (Frequently Asked Questions):

• Q: What should I do if the kettle stops working suddenly?
  A: If the kettle stops working unexpectedly, check the power source and ensure it is properly connected. If the issue persists, contact our customer service for further assistance.

• Q: Can I heat beverages other than water in the kettle?
  A: No, the kettle is designed specifically for heating water and should not be used for heating other liquids to avoid damage to the product.

FOREWORD

About this document
This manual contains all the information for correct, efficient and safe use of the product. Make sure you have fully read and understood the instructions in this manual before installing or using the product. Keep this manual for future use.

Original Instructions
This manual was originally written in Dutch. All other languages are translations of the original Dutch manual.

Service and warranty
If you need service or information regarding your product, please contact our customer service at service@kitchenbrothers.nl.
We provide a 2-year warranty on our products. Customer must be able to show proof of purchase when claiming warranty. Product defects must be reported to us within 2 years from the date of purchase. Please note that the warranty does not apply: for damage caused by improper use or repair; for parts subject to wear and tear; for defects known to the customer at the time of purchase; for defects caused by the customer’s own fault, for damage caused by third parties.

INTRODUCTION

Thank you for choosing a KitchenBrothers product! Please always follow the instructions for safe usage.

Intended use
A kettle is intended only for heating or boiling water. It is not intended for heating other liquids. A kettle heats water using an electric heating element.
The supplier is released from liability for any injury or damage caused by using the product beyond its intended use. Any modification of the product may affect your safety and warranty.

Product Overview

1. Lid with knob
2. Pour spout
3. Water level and LED indicator
4. Base with power connection
5. Display
6. +/- button
7. On/Off button

Product specifications

*Recommended

Other features

• Choice of 7 adjustable temperatures.
• Keep Warm feature with memory.
• Smart LED lighting with temperature indicator.
• Removable limescale filter.
• Concealed heating element: easy to descale.

Contents of package
When receiving your shipment, make sure that the contents are consistent with the packing list. Notify your distributor of any missing items. If the equipment appears to be damaged, file a claim immediately with the carrier and notify your distributor at once, giving a detailed description of any damage. Save the damaged parts and packing container to substantiate your claim.
KitchenBrothers Kettle with temperature control – 1.7 l – Stainless steel – Model KB4065 – EAN 8721055561309
KitchenBrothers Kettle with temperature control – 1.7 l – Black – Model KB4066 – EAN 8721055561316

Included accessories

• 1x User manual

SAFETY

Warning! Please ensure that the packaging is kept out of the reach of children! Risk of suffocation!

Before use, read the manual and safety information carefully. The supplier is not responsible for failure to follow the safety information on the use and handling of the product or damage to property or personal injury.
Always observe the following precautions when using ‘the Kettle with temperature control’, hereinafter referred to as ‘the product’.

General

• If this is your first time using the product, it is important to read the manual and instructions carefully.
• If the product is malfunctioning, dropped or damaged, do not use the product and consult our customer service.
• Before each use, check the parts and accessories for any damage or wear (cracks/breakage) that may adversely affect performance and, if so, replace them with original or manufacturer-recommended parts and accessories.
• Do not use accessories not offered by the supplier. They may pose a danger to the user and damage the product.
• Use the product only for the purposes indicated in this manual.
• Do not disassemble, repair or restore the product. Doing so may cause damage to the product. For your own safety, these parts should only be replaced by authorized service personnel. Always send the product to a service center for repairs to prevent damage and personal injury.
• Be aware of the risks and consequences associated with improper use of the product. Misuse of the product may result in personal injury and damage to the product.
• Before first use, remove all packaging material and any stickers.
• The outside of the product may become hot when the product is in use. So be alert when touching the outside!
• The product is only suitable for indoor use. Do not use the product outdoors. This may result in damage to the product.
• The product is intended for domestic and commercial use such as; in staff kitchens; in retail stores; in offices and other work environments; by customers in hotels, motels and other residential environments; in bed & breakfast environments; on farms.
• Due to residual heat, the heating element remains hot after use. Do not touch the hot surface. Doing so may result in personal injury.

Persons

• If burns occur, immediately run lukewarm water over the affected body part. Do not stop to remove clothing and seek medical attention quickly.
• The product should not be used by children under 8 years of age. Use of the product is permitted only when a supervisor is present and responsible for the safety of the user.
• The product may be used by children 8 years of age and older, provided that they are properly supervised and instructed in the safe use of the product and understand its potential dangers.
• The product may be used by people with physical or mental disabilities, provided that they are properly instructed and informed on the safe use of the product and understand its potential hazards.
• Keep the product and cord out of the reach of children and pets.
• To avoid electric shock, do not allow pets or small children to chew on the power cord.
• Do not allow children to play with the product. Use and store the product out of the reach of children.

Use

• Always place the product on a stable, firm and level surface.
• The product becomes hot when it is on. Do not use the product if you are sensitive to heat. Do not touch the hot parts of the product. Use only the handle or knob.
• Wait for the product to cool down before cleaning it.
• Do not cover the product when it is on. Never place pillows or blankets on or against the product. This may cause a fire hazard, electric shock, personal injury or damage to the product.
• Unplug the product when it is not on: when it is empty, when filling water, when not in use, or when moving or cleaning the product.
• Connecting and disconnecting the power circuit should be done with dry hands on a dry surface when the product is turned off.
• Hot steam comes out of the product when the water is boiling or has just boiled. Avoid any contact with this hot steam, you could get burned.
• Do not use the product if the water tank is empty. This may cause damage to the heating elements.
• The product is only suitable for heating water. Never use the product to heat other liquids (such as coffee, tea or alcohol).
• Make sure that the water in the product is always between the minimum and maximum lines. If there is less water in it, the heating element may overheat. If there is more water in it, hot water will spray over the edge.
• Be very careful when moving the product so that no hot water splashes out. Always hold the product by the handle.
• Residual water in the product will not be drinkable the next day. Do not leave water in the product to avoid scaling.
• Make sure the display and buttons do not get wet.

Electronics

• The product should only be connected to a grounded 220-240V outlet.

• If the power fails during use, turn off the product immediately and unplug the product.

• If the surface of the product is cracked, turn off the product to avoid electric shock.

• Check both power cord and plug regularly for signs of damage or wear, and
  if there is any, do not use the product and have the power cord and/or plug replaced or repaired by authorized service personnel.

• Do not immerse the product, power cord or plug in water. If water does get inside or on the product, turn the product off immediately and contact our customer service department.

• Use and store the product so that the cables cannot be damaged.

• To avoid electric shock, do not use the product if you suspect the power cord or plug is damaged. A damaged power cord or plug should be repaired or replaced by a professional (an authorized distributor).

• Do not unplug the product by pulling the power cord. This may cause fire or electric shock.

• If black smoke comes out of the product, unplug the product immediately. Wait until the smoke is gone before removing the contents of the product and contact our customer service department.

• Do not leave the cable(s) hanging over the edge of a table or countertop.

• Do not place the cable(s) on hot surfaces or near oil.

• Do not tuck the cable(s) under rugs or blankets. Never lay the cable(s) in a walkway.

• Do not move the product by pulling the cord or twist the cord.

• Before connecting the product, make sure that the mains voltage indicated on the rating plate matches that of your mains supply.

• Make sure that you do not trip over the cable(s) and that the cable(s) are not kinked, twisted, or stuck.

• Do not leave the product unattended when in use. If you are not using the product for a long time, turn the product off and unplug it.

• Do not move the product when it is on. Always turn the product off before moving or cleaning it.

• Turn the product off and unplug the product when not in use or cleaning. Let the product cool down completely before cleaning or storing the product.

INSTRUCTIONS FOR USE

Before first use
Before using the product for the first time, clean it thoroughly (see also Chapter 5):

1. Clean the exterior with a damp cloth.
2. Boil water (see chapter 3.2).
3. Throw away the boiled water without drinking it.
4. Rinse the inside of the product with fresh water.
5. The product is now ready for use.

Heating water at 100°C

1. Plug the base into a grounded outlet.
2. Remove the product from the base.
3. Press the button to open the lid.
4. Fill the product with drinking water between the MIN line and the MAX line.
5. Close the lid and put the product back on the base.
6. “ON” appears on the display. Then the current water temperature is displayed.
7. Press the on/off button to boil the water directly to 100°C.
8. The display shows “100°C” and the water is immediately heated to 100 degrees. During heating, the display shows the current temperature.
9. The product automatically turns off when the water has boiled. The light turns off. You can also interrupt heating the water at any time by pressing the on/off button.
10. You can now pour the water carefully in an container suitable for hot liquids.
11. Unplug the product after use. Do not leave water in the product to prevent scaling.

ATTENTION!

• Burn hazard from hot steam and hot water. Be very careful when moving the product so that hot water does not splash out. Always hold the product by the handle.
• Always close the lid before turning on the product. If the lid is open, the product will not work properly and there is a risk of injury.

Temperature selection

• To select a different temperature, first follow steps 1 to 6 from chapter 3.2.
• Then press the +/- button to select the desired temperature (40/50/60/70/80/90/100°C). Only then press the on/off button.
• The selected temperature flashes 3x on the display. After that, the display shows the current water temperature during heating.

LED indicator
During heating, the color of the LED changes to indicate the temperature:

Keep Warm function
The Keep Warm function keeps the boiled water at the desired temperature for up to 2 hours and reheats it in between. This function has a memory: If you remove the product from the base to pour water and then put it back on the base, the Keep Warm function remains active.

1. Follow steps 1 to 6 from chapter 3.2.
2. Use the +/- button to select the desired temperature (40/50/60/70/80/90/100°C).
3. When the desired temperature appears on the display, do not release the button. Press and hold the “+/-” button until the Keep Warm symbol becomes visible (see illustration).
4. Then press the on/off button.
5. If the water is not yet at the selected temperature, it will be heated first.
6. Then the water in the product is automatically kept warm at the selected temperature for up to 2 hours. To do this, the water is reheated periodically.
7. To turn the Keep Warm function off again, press and hold the +/- button again for a moment.

Overheating protection
The product is equipped with an automatic shutdown to prevent overheating of the heating elements. In the event of overheating, the heating elements will automatically shut off. If this happens, let the product cool down for about 20 minutes before using it again.
To prevent overheating:

• Descale the product regularly (see chapter 5).
• Only turn on the product when enough water is in it (between the MIN line and the MAX line).

TROUBLESHOOTING

If the following problems occur while using the product, refer to the table below to find a solution. If the problems cannot be solved using these options, please contact our customer service.

device is plugged into a suitable and working electrical outlet.
Make sure the product makes good contact with the base by turning it slightly.
The product is connected correctly but

the water is not heated.

| The overheating protection is on.| The product has been left on with too little water. Empty the product and let it cool for at least 20 minutes. Then fill the product with at least 0.5 liters of cold water.
There is too much lime on the heating elements. Descale the product (see chapter 5).
The light does not come on.| The lamp or the lamp cable is damaged.| Contact customer service.
---|---|---
Water runs down the outside of the product or water accumulates under the base.| There is too much water in the product.| Unplug the product. Completely dry the product. Never fill the product above the MAX line.
Water has been spilled when filling or moving the product.| Unplug the product. Dry the product completely. Keep the product straight when filled with water.
The product is leaking.| Unplug the product. Dry the product completely. Check the product for leaks. If it leaks, stop using the product and contact customer service.
The base becomes unexpectedly hot during use.| The power connector in the center of the base or the pins on the bottom of the kettle are damaged.| Unplug the product from the power outlet. Check the power

connector and pins for discoloration or deformation. Stop using the product if the pins are not smooth and clean. Do not attempt to clean or repair and contact customer service.

The power cord is damaged.| Contact an authorized service center for replacement.

MAINTENANCE AND CLEANING

ATTENTION!

• Never immerse the product in water.
• Make sure that the power points in the center of the base and in the bottom of the product always remain dry.

Cleaning the product

1. Unplug the product from the power outlet.
2. Remove the product from the base and let it cool down.
3. Open the lid and rinse the inside with tap water.
4. If necessary, descale the product (see section 5.3).
5. Wipe the base and power cord with a slightly damp cloth. Always ensure that the plug remains completely dry.
6. Wipe the outside of the kettle with a damp cloth.
7. Dry all parts thoroughly with a dry cloth. Then allow the parts of the product to dry naturally for about 30 minutes.

Cleaning the filter

1. Grasp the top of the filter and pull it upwards.
2. Clean the filter with clean water.
3. Dry the filter thoroughly before replacing it.

Descaling
Depending on your water hardness, the product should be cleaned regularly. If the product is not descaled regularly, the temperature control will not work as well, which can lead to energy loss and overheating of the heating element. Therefore, it is important to descale the product at least twice a year.

1. Fill the product with 0.5 liter of vinegar and add water to the MAX line.
2. Turn on the product and bring the mixture to a boil.
3. Then let it soak overnight.
4. The next morning, discard the mixture and rinse the inside with clear tap water.
5. Fill the product to the MAX line with water and let the water boil.
6. Discard the water to remove traces of lime and vinegar.
7. Rinse the inside well with clean water.

**STORAGE

**

Store the product in a clean and dry place. Do not store the product in extreme high or extreme low temperatures.

DISPOSAL AND RECYCLE
Think about the environment and contribute to a cleaner living environment! You can contact your local council for all information on disposal options for discarded products.

Disposal
At the end of its life, do not dispose of the product with normal household waste, but hand it in at a government-designated collection point for recycling.

Dispose of the packaging and accessories in accordance with the environmental regulations in force in your local council. Pay attention to the symbols on the different packaging materials and – if necessary – dispose of them separately. The packaging materials are marked with letters and numbers: 1-7: plastic, 20-22: paper and cardboard, 80-98 composite materials.

Electric appliance
The symbol shown here with the crossed-out garbage can indicates that this product is subject to European Directive (EU) 2012/19/EU. This directive states that at the end of its service life, you must not dispose of this product with normal household waste, but hand it in at a government-designated collection point for recycling.

SYMBOLS

The following warnings and symbols are used in this manual, on the packaging and on the product (where applicable).

CE DECLARATION OF CONFORMITY
This product complies with all requirements and regulations according to 2014/35/EU, Directive 2014/30/EU and Directive 2009/125/EC.

The complete EU Declaration of Conformity is available at the supplier.

DISCLAIMER
Changes reserved; specifications are subject to change without stating grounds for doing so.

User manual – Translation of the original manual
Made in China

©LifeGoods B.V.
Wisselweg 33, 1314 CB Almere (NL)
www.kitchenbrothers.nl
service@kitchenbrothers.nl

References

• KitchenBrothers - Keukenartikelen voor gemak en plezier

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>