WORKHORSE WHCC-1M1UNV210P-75L Constant Current LED Driver Owner’s Manual

: August 17, 2024
: WORKHORSE

Table of Contents

WORKHORSE WHCC-1M1UNV210P-75L Constant Current LED Driver
Product Information
Product Usage Instructions:
General Specifications
Charts
Warranty
Programming
Mechanical Drawing
Packaging
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WORKHORSE WHCC-1M1UNV210P-75L Constant Current LED Driver

Product Information

Specifications

Model: WHCC-1M1UNV210P-75L
IP Rating: IP66 E342838
Input Voltage: 100~277VAC, 50/60Hz
Dimming: Bi-Level Dimming using 0-10V
Type: Constant Current LED Driver
Output Voltage: 28-56VDC
Programmable Current: 350mA-2100mA
Programmable Min. Dim Level: 0-10V dimmable from 100%-10%
Suitability: Dry and Damp locations
Other Features: Flicker-Free (0.92)

Product Usage Instructions:

Installation

Ensure power is switched off before installation.
Connect the input wires to the power supply following the provided wiring diagram.
Connect the output wires to the LED fixture ensuring correct polarity.
Secure all connections properly before restoring power.

Dimming Settings:
The driver supports bi-level dimming using a 0-10V signal. Adjust the dimming level as per your preference within the range of 100%-10% by adjusting the programming settings.

Maintenance
Regularly inspect the driver for any signs of damage or wear. Clean the unit gently if required, ensuring it is disconnected frompower during maintenance.

Safety Precautions

Do not expose the driver to water or moisture beyond its IP66 rating.
Avoid overloading the driver beyond the specified current limits.
If in doubt, consult a qualified electrician for installation and troubleshooting.

FAQ

Q: Can this LED driver be used in outdoor applications?
A: Yes, this LED driver is suitable for dry and damp locations and has an IP66 rating, making it suitable for outdoor use.
Q: What is the flicker-free feature mentioned in the product description?
A: The flicker-free feature indicates that the LED driver provides stable and consistent power output, reducing any flickering effects in the connected LED fixtures.

WHCC-1M1UNV210P-75L

Constant Current LED Driver

100~277VAC, 50/60Hz
Output Voltage: 28-56VDC
Programmable Current: 350mA-2100mA
Flicker -Free (<4%)
Bi-Level Dimming using 0-10V
Prog. Min. Dim Level
0-10V dimmable from 100%-10%
Input Surge Line-Neutral 6KV, Line & Neutral-Ground 10KV
IP66 , Type HL
Suitable for Dry and Damp location

General Specifications

Charts

Part Number Matrix

Grounding
Driver must be grounded by means of the Driver case.

Over temperature protection
The Fulham Workhorse LED drivers is protected against thermal overload. If the temperature limit is exceeded, the output current is reduced.

LED load
Fulham Workhorse LED drivers are designed to drive passive LEDs, -COB’s and -LED assemblies .Proper function is not guaranteed when (LED)loads with active components are used.

Short-circuit protection
In case of a short circuit the LED driver switches to protection mode. After the removal of the short-circuit the LED driver will recover automatically.

No-load Operation

In no-load operation the output voltage will not exceed the specified open circuit output voltage.
It’s not recommended to use this product for a long time without load.

Hot Swapping
This driver does not support hot swapping of the LEDs.

Remote Mounting
Up to 50ft(3657.6mm) with 18AWG(0.823mm²). Contact Fulham for higher remote distance.

Service life/Lifetime
Failure Rate Info based upon MTBF modeling: 90% survivals at end of life @ <=Tc lifetime rating.

Warranty

Reference Fulham’s limited Warranty: https://cdn.fulham.com/PDFs/Limited- Warranty.pdf

Programming

TPSB-100 Programming Controller
Please consult the user manual for instructions on using the TPSB-100 SmartSet Programming Controller.

Programming Instructions

To program use the Fulham TPSB-100 SmartSet controller; connect the programming forks in to the appropriately labeled programming connections located on the LED driver.
Program the driver output current between 350mA-2100mA (Note: set current represents total current of one channel).
Current programming and more function setting can be done through SmartSet PC Software.

Mechanical Drawing

Overall Dimensions

Wiring Diagram

Product Image:

Packaging

Master Carton

OUTER DIMENSION

L| W| H
14.37”(365mm)| 10.24”(260mm)| 4.72”(120mm)
Net
Weight| Gross
Weight| QUANTITY
12.35lbs.

(5.6 kg)

| 13.56lbs.
(6.15 kg)| 10pcs.

Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 Tel.: 1-323-779-2980 Fax.: 1-323-754-9060. order@fulham.com www.fulham.com Specifications subject to change without notice.